Page History

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access System > Node-Level Settings. The Node-Level Settings page is displayed.
3. Configure the NTP and DNS Servers with network-specific data.
4. Leave all other parameters as default.

5. Click Apply.
   

   Caption0Table1

   
   

   TLS Configuration - Example Values

   Parameter	Example Value
   Host Name	aepsite6
   Domain Name	SonusMS01.com
   Use NTP	Yes
   NTP Server	Specifies the FQDN, IPv4, or IPv6 address of the NTP server. If the host name is supplied, the SBC uses the DNS to connect to the NTP server.
   Use Primary DNS	Yes
   Primary Server IP	XXX.XXX.XX.XXX

   Caption0Figure1

   
   

   Node-level Settings - Example

   Image Modified

   
   

Configure Logical Interface

...

1. In the WebUI, click the Settings tab.
2. In the left navigation pane, go to Node Interfaces > Logical Interfaces.
3. Configure the parameters as shown below (example values are shown in the table; configure as per your network requirements). For details on field descriptions, refer to Configuring and Modifying Logical Interfaces.
4. Leave all other parameters as default.

5. Click Apply.
   

   Pagebreak

   Caption0Table
   1

   
   Logical Interfaces Configuration - Example Values

   Parameter	Example Value
   Alias	To Microsoft Phone 5
   Description	Interface to Interconnect with Microsoft Phone System
   Admin Interface	Enable
   IP Assign Method	Static
   Primary Address	<Public IP of your SBC> (in the example 192.168.211.80)
   Primary Netmask	<Mask of Public Interface of your SBC> (in the example 255.255.255.0)

   Caption0Figure1

   
   

   Logical Interfaces - Example

   Image Modified

   
   

Create Profiles

For interconnecting with Microsoft System Direct Routing, the following profiles are required:

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access SIP > SIP Profiles.
3. Click Add at the top of left corner and add a new SIP profile.
4. Configure the parameters as shown below (example values are shown in the table; configure as per your network requirements). For details on field descriptions, refer to Creating and Modifying SIP Profiles.
5. Leave all other parameters as default.

6. Click OK.

   Caption0Table

   
   

   1

   
   SIP Profile Configuration - Example Values

   Parameter	Example Value
   Description	Teams Direct Routing Profile
   FQDN in From Header	SBC Edge FQDN
   FQDN In Contact Header	SBC

   FQDN

   FQDN NOTE: For Microsoft Teams, the Signaling Group facing the Teams server must be configured as SBC Edge FQDN or Static (if there is more than one signaling group connected to Teams Direct Routing). The FQDN in Contact Header should be the same FQDN used in Office 365 Tenant Online Gateway. If the IP Address of the SBC is configured in the Contact Header instead of the FQDN of the SBC, a Forbidden message is received. NOTE: If you set this field to Static and you expect the port number of the Contact header in the outbound SIP messages, you must configure the Static Host FQDN/IP field with the Listen Port number of the SIP signaling group.

   Origin Field Username

   <FQDN of SBC> (in the example aepsite6.SonusMS01.com)

   Pagebreak

   Caption0Figure1
   
   SIP Profile - Example

   Image Modified

   
   

Create Analog Device Profile

...

1. In the WebUI, click the Settings tab.
2. In the left navigation pane, go to CAS > CAS Signaling Profiles.
3. From the Create CAS Profile drop down box, select FXS Profile.
4. Configure the parameters as shown below. Leave the default values for all other parameters.

5. Click OK.

   caption1

   
   

   0Table

   
   

   Analog Profile Entries - Example Values

   Parameter	Value
   Description	Analog Device
   Loop Start Type	Specifies the loop start method. This field is country-specific, and may need to be adjusted for your country.
   Disconnect Tone Generation	Specifies whether or not a disconnect tone is generated when a call is disconnected from the far end. This field is country-specific, and may need to be adjusted for your country.

   Caption0Figure

   
   

   1Analog

   Analog Device Profile - Example

   Image Modified

   
   

Create SDES-SRTP Profile

The SDES-SRTP Profile defines the encryption mechanism used between the SBC and the Microsoft Teams Direct Routing interface; the Crypto Suite specifies the algorithm used to negotiate with a peer device.

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access Media > SDES-SRTP.
3. Click Add at the top left corner and add a new SDES-SRTP Profile.
4. Configure the parameters as shown below. For details on field descriptions, refer to Creating and Modifying SIP Profiles.

5. Leave all other parameters as default.

   Caption0Table1

   
   
   Media Crypto Profile Configuration - Example Values

   Parameter	Example Value
   Description	Teams Direct Routing SRTP
   Operation Option	Required
   Crypto Suite	AES_CM_128_HMAC_SHA1_80

   Caption0Figure
   1

   
   

   Media Crypto Profile - Example

   Image Modified
   
   

Anchor
MediaList MediaList

Create Media List

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access Media > Media List.
3. Click Add at the top left corner and add a new Media List.
4. Configure parameters as shown below. For details on field descriptions, refer to Creating and Modifying Media Lists.

5. Leave all other parameters as default.

   Caption0Table1

   
   
   Media List Configuration - Example Values

   Parameter	Example Value
   Description	Teams Direct Routing Media List
   Media Profiles List	In the Media Profiles List field, click Add/Edit. G711a and G711u are the default Media Profiles. G711a G711u NOTE: See Microsoft documentation for the list of codecs supported by Microsoft.
   SDES-SRTP Profile	Teams Direct Routing SRTP. This profile was created in the previous step.

   Caption0
   Figure

   
   

   1

   Media List - Example

   Image Modified

   
   

Configure a SIP Server Table

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access SIP > SIP Server Tables
   
3. Click Add at the top left corner and add a new SIP Server Table.
4. For Description, enter Teams Direct Routing Server.
   

5. Click OK.

   Caption0Figure1

   Create SIP Server Table

   Image Modified

   
   

Configure Entries in the Teams Direct Routing Server

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access SIP > SIP Server Tables.
3. Select the name of the table created in the previous step.
4. From the Create SIP Server drop down list, select IP/FQDN.

5. Repeat this configuration for two additional SIP Server entries, using the field entries below. For details on field descriptions, refer to Creating and Modifying Entries in SIP Server Tables.
   

   Caption0Table1SIP Server 1

   
   

   SIP Server 1 Table - Example Values

   Parameter	Value
   Priority	1
   Host	sip.pstnhub.microsoft.com
   Port	5061
   Protocol	TLS
   TLS Profile	Teams Direct Routing TLS
   Monitor	SIP Options

   Pagebreak

   Caption0Figure1
   
   SIP Server 1 - Example Values

   Image Modified

   Caption0Table

   1
   

   SIP Server 2 Table - Example Values

   Parameter	Value
   Priority	2
   Host	sip2.pstnhub.microsoft.com
   Port	5061
   Protocol	TLS
   TLS Profile	Teams Direct Routing TLS
   Monitor	SIP Options

   Caption0Figure1

   
   

   SIP Server 2 - Example Values

    

   Image Modified

   Pagebreak

   Caption01
   Table

   
   

   SIP Server 3 Table - Example Values

   Parameter	Value
   Priority	3
   Host	sip3.pstnhub.microsoft.com
   Port	5061
   Protocol	TLS
   TLS Profile	Microsoft Phone System
   Monitor	SIP Options

   Caption0Figure1

   
   SIP Server 3 - Example Values

   Image Modified

   
   

Create Transformation Tables and Entries

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access Call Routing > Transformation
   
3. Click Add at the top left corner to add a new Transformation Table.
4. For Description, enter From Microsoft Teams to Analog Device
   

5. Click OK.

   Caption
   0 Figure 1 Create Transformation Table
   Image Removed

   Image Added

6. In the left navigation panelIn the left navigation panel, select the new table:  Transformation > From Microsoft Teams to Analog Device
   
7. Click Create.
8. Configure the parameters as shown below. Leave the default values for all other parameters.

9. Click OK.

   Caption0Table1

   
   
   Transformation Entries - Example Values

   Parameter	Value
   Description	Extract Analog Device Extension Number
   Match Type	Optional (Match One)
   Input Field	Type: Called Address/Number Value: .*3(\d{3})
   Output Field	Type: Called Address Number Value: \1

   Pagebreak

   caption1
   0Figure

   
   

   Transformation Entry - Example

   Image Modified

   
     Caption0Figure

   1
   

   Transformation Table - Entry Added

   Image Modified

   
   

Calls From Analog Device to Microsoft Teams

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access Call Routing> Transformation
   
3. Click Add at the top left corner to add a new Transformation Table.
4. For Description, enter From Analog Device to Microsoft Teams
   

5. Click OK.

   Caption0Figure1Create Transformation Table

   Image Modified

6. In the left navigation panel, select the new table:  Transformation > From Analog Device to Microsoft Teams
   
7. Click Create.
8. Configure the parameters as shown below. Leave the default values for all other parameters.

9. Click OK.

   caption1

   
   

   0Table

   
   

   Transformation Entries - Example Values

   Parameter	Value
   Description	Convert to Teams Client Number
   Match Type	Optional (Match One)
   Input Field	Type: Called Address/NumberValue: (.*)
   Output Field	Type: Called Address NumberValue: \1

   Caption0Figure1Transformation

   
   

   Transformation Table Entry

   Image Modified

   Caption0Figure1

   
   

   Transformation Table - Entry Added

   Image Modified

   
   

Create Signaling Groups

Signaling groups allow telephony channels to be grouped together for the purposes of routing and shared configuration. In the case of SIP, they specify protocol settings and link to server, media and mapping tables. For Teams Direct Routing, you configure the Signaling Group to designate routing information for calls between SBC Edge and the Microsoft Phone System. Two Signaling Groups are required:

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access Signaling Groups
   
3. From the Create Signaling Group drop down box, select SIP Signaling Group.
4. Configure the parameters as shown below. Leave the default values for all other parameters.

5. Click OK.

   Caption0Table

   
   

   1

   
   Signaling Group Configuration - Example Values

   Parameter	Value
   Description	Microsoft Teams
   SIP Profile	Teams Direct Routing Profile
   Media List ID	Team Direct Routing List
   Signaling Media/Private IP	Ethernet 1 (example, choose the interface which faces Microsoft Teams Direct Routing)
   Listen Port	5061 TLS
   Federated IP/FQDN	sip-all.pstnhub.microsoft.com
   SIP server table	Teams Direct Routing Server
   Load Balancing	Priority: Register All
   SIP Profile	Microsoft Phone System (from previous step)
   Call Routing Table	Default Routing Table
   Outbound NAT Traversal*	Static NAT
   NAT Public IP*	IP Address (Only required if “Static NAT” is selected)
   Static NAT Inbound	Disabled (this field should not be configured for Non-Media Bypass Teams deployment)

   *Outbound NAT Traversal and the NAT Public IP is required when the SBC is behind a NAT (the public IP address of the NAT device is required when the SBC has a Private IP).
   

   Pagebreak

   Caption0Figure1
   
   Signaling Group - Example

   Image Modified

   
   

   
   

Calls from Analog Device to Microsoft Teams

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access Signaling Groups
   
3. From the Create Signaling Group drop down box, select CAS Signaling Group.
4. Configure the parameters as shown below. Leave the default values for all other parameters.

5. Click OK.

   Caption0

   
   

   Table1

   
   Signaling Group Configuration - Example Values

   Parameter	Value
   Description	Analog Device
   CAS Signaling Profile	Select (FXS) Analog Device
   Caller ID Type	Country-specific
   Assigned Channels	Assign CAS channels.
   Call Routing Table	Default Routing Table

   Caption0Figure1

   
   Signaling Group - Example

   Image Modified

Create Call Routing Tables

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access Call Routing Table.
   

3. Click Add at the top left corner and add a new Call Routing Table.

   Caption
   0 Figure 1 Create Call Routing Table
   Image Removed

   Image Added

4. Configure the Description as From Configure the Description as From Microsoft Teams and click OK.
5. From the left navigation pane, click on the Call Routing > Call Routing table.
   
6. Select From Microsoft Teams (the entry you just created).
7. Click Add.
8. Configure the parameters as shown below. Leave all other parameters as default.

9. Click OK.

   Caption0Table1

   
   
   Call Routing Table Configuration - Example

   Parameter	Value
   Description	From Microsoft Teams to Analog Device
   Number/Name Transformation Table	From Microsoft Teams to Analog (select Transformation Table you created above)
   Destination Signaling Groups	From Microsoft Teams

   Pagebreak

   Caption0Figure1

   
   

   Call Routing Table - Example

   Image Modified

   
   

From Analog Device to Microsoft Teams

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access Call Routing Table.
   

3. Click Add at the top of  left corner and add a new Call Routing Table.

   Caption0

   Figure1Create Call Routing Table

   Image Modified

4. Configure the Description as Microsoft Phone system and click OK.
5. From the left navigation pane, click on the Call Routing > Call Routing table.
   
6. Select From Analog Device (the entry you just created).
7. Click Add.
8. Configure the parameters as shown below. Leave all other parameters as default.

9. Click OK.
   

   Caption0Table1

   
   

   Call Routing Table Configuration - Example

   Parameter	Value
   Description	From Analog Device to Microsoft Teams
   Number/Name Transformation Table	From Analog Device to Microsoft Teams (select Transformation Table you created above)
   Destination Signaling Groups	From Analog Device

   
   Caption0Figure
   1

   
   Call Routing Table - Example

   Image Modified

   
   

Update Signaling Groups for Call Route

...

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access Signaling Groups > Teams Direct Routing.
3. From the Call Routing Drop down list, select From Microsoft Teams.

4. Click OK.
   

   Caption0Figure1Select Call Routing Table - Teams Direct Routing

   
   

   Image Modified

   
   

Associate Call Route to Signaling Group for Calls from an Analog Device to Teams

1. In the WebUI, click the Settings tab.
2. In the left navigation page, access Signaling Groups > From Analog Device.
   
3. From the Call Routing Drop down list, select From Analog Device.
   

4. Click OK.

   Caption0Figure1Select Call Routing Table - From SIP Trunk

   
   

   Image Modified