Page History

Include Page
SBXDOC101:_SBC 5100 5200 UnsupportedSBXDOC101: _SBC 5100 5200 Unsupported

SBC 5000 Series Hardware Platforms

Ribbon

Spacevars
0 series

is available in four different platforms. The 

Spacevars
0 series

platforms are similar as they use the same types of components, but different models provide different hardware and capacity capabilities. All SBC 5000 hardware platforms support the Ribbon SBC application software.

• SBC 5100 Platform—Small to medium session count deployments. The capacities make this product particularly well suited for medium enterprises and small to medium service providers.SBC 5110 Platform—This is a modular form SBC that targets small and medium count deployments. This SBC model allows you to field install digital signal processor (DSP) cards as their network expands.SBC 5200 Platform—Medium to large session count deployments. The capacities make this product particularly well suited for large enterprises and medium to large service providers.
• SBC 5210 Platform—This is a modular form SBC that targets medium to large session count deployments. This SBC model allows you to field install digital signal processor (DSP) cards as their network expands.
• SBC 5400 Platform—The

  Spacevars
  0 model5

   hardware platform comes equipped with four media ports and is available in three models based on the media port configuration. You must purchase the appropriate model based on their interface and capacity requirements. The media ports are enabled on the chassis depending upon the network interface license installed. For SBC 5400 Hardware information, refer to Installing SBC 5000 Series Hardware.

Hardware Specifications

SBC 5100

Caption
0 Figure 1 SBC 5100 Front View
Image Removed

Caption0Figure1

SBC

5100 Rear View

Image Removed

Caption

0	Table
1	5100 Specifications

Front PanelRear PanelExpansion StorageMemory Power Option

• Status Indicators Front Panel LEDs
• Single USB V2.0 interface

• Two 10/100 Management Ports
• Two Media Ports
• Two High Availability Ports
• Single Field Service port with RJ45 connector
• Locator LED
• Alarm port with DB15 connector
• Single serial craft DB9 port

DSP expansion card
(SPS100 / SPS100DB) 

80 GB (minimum), 120 GB, or 128 GB Solid State Disk (SSD)

12 GB RAM  AC and DC 

SBC 5110

Caption
0 Figure 1 SBC 5110 Front View

Caption
0 Figure 1 SBC 5110 Rear View

Caption
0 Table 1 5110 Specifications

3

Caption
0	Figure
1	SBC 5200 Front View
Front Panel Rear Panel Expansion (Modular)  Storage Memory  Power Option Status Indicators Front Panel LEDs Single USB V2.0 interface Two 10/100 Management Ports Two Media Ports Two High Availability Ports Single Field Service port with RJ45 connector Locator LED Alarm port with DB15 connector Single serial craft DB9 port Up to four DSP 25 cards, or one DSP 20 card 80 GB (minimum), 120 GB, or 128 GB Solid State Disk (SSD)  24 GB RAM   AC and DC

SBC 5200

SBC

5200 Front View

Image Removed

Caption
0 Figure 1 SBC 5200 Rear View
Image Removed

Caption

0	Table
1	5200 Specifications

SBC 5210

Caption
0 Figure 1 SBC 5210 Front View

Caption
0 Figure 1 SBC 5210 Rear View

Caption
0 Table 1 5210 Specifications
Front Panel Rear Panel Expansion (Modular)  Storage Memory  Power Option Status Indicators Front Panel LEDs Single USB V2.0 interface Two 10/100 Management Ports Four Media Ports Two High Availability Ports Single Field Service port with RJ45 connector Locator LED Alarm port with DB15 connector Single serial craft DB9 port Up to four DSP 25 cards, or one DSP 20 card 256 GB (minimum)  or 300 GB Solid State Disk (SSD) 24 GB RAM   AC and DC

Note
Note: The HA mode can support mix SSD capacity. The show table system hardDiskStatus may show different SSD sizes. The shipped SSD size is determined based on availability.

Chassis

The Ribbon 

Spacevars
0 series

 2U rack-mounted chassis can be front or center mounted in standard 19” or 23" wide racks.

The SBC 5100/5200 chassis accommodates following modules:

Motherboard

Optional DSP base card

Up to two optional DSP expansion cards (SPS100 / SPS100DB)

The SBC 5110/5210 chassis accommodates following modules:

• Motherboard
• Up to four DSP 25 modules or one DSP 20 modules

Note
The chassis must be installed in adherence with the environmental specifications and power source requirements listed in Post Installation Checklist.

Front Panel

The 

Spacevars
0 series

chassis includes a front panel on which the various input/output ports and LEDs are located.

 The SBC 5000 Series Hardware Platform Specifications#Front  The Front Bezel and LEDs of SBC 5100/ 5110 Series figure shows the front panel LEDs with and without Bezel mounted on the front panel of SBC 5100/ 5110. AnchorFP-5100FP-5100

Caption

0	Figure
1	Front Bezel and LEDs of SBC 5100/5110 Series
3	Front Bezel and LEDs of SBC 5100/5110 Series

Image Modified

Image Modified

The SBC 5000 Series Hardware Platform Specifications#Front The Front Bezel and LEDs of SBC 5200/ 5210 Series figure shows the front panel LEDs with and without Bezel mounted on the front panel of SBC 5200/ 5210. AnchorFP-5200FP-5200

Caption

0	Figure
1	Front Bezel and LEDs of SBC 5200/5210 Series
3	Front Bezel and LEDs of SBC 5200/5210 Series

Image Modified

Image Modified

The SBC 5000 Series Hardware Platform Specifications#Front Front panel LEDs Description table lists the front panel LEDs on the

Spacevars
0 series

. The default state of all LEDs are during a reset.

Caption0Table1Front panel LEDs Description3Front panel LEDs Description

Network Ports and Connection

The 

Spacevars
0 series

chassis comprises the following external input and output ports:

• Alarm contacts are provided on the outside of the chassis via a single shielded male DB15 connector.
• A standard USB connector on the front of the chassis.
• Front and rear jacks for standard ESD straps.
• Cable management.

Note
The SBC 5000 system The  Spacevars 0 series supports USB 2.0.

Rear Panel

The following figures list the rear panel LEDs on the the 

Spacevars
0 product

 

Spacevars
0 model4

 and

Spacevars
0 seriesmodel2

. The default state of all LEDs is during a reset. The rear panel layout and LEDs are as depicted in the SBC 5000 Series Hardware Platform Specifications#Rear Rear Panel LEDs for SBC 5200 Series figure:

Caption0

Figure1Rear Panel LEDs for SBC 5200 Series

SBC 5110

Image Modified

Caption

0Figure1Rear Panel LEDs for

SBC 5210

Series

Image Modified

Caption
0 Figure 1 Rear Panel LEDs for SBC 5100 Series
Image Removed

Caption
0 Figure 1 Rear Panel LEDs for SBC 5110 Series
Image Removed

The SBC 5000 Series Hardware Platform Specifications#Rear Panel The Rear Panel Description table lists the Ethernet port LEDs. Each of the Management ports, Media ports, HA ports, and FSP port support the following LEDs.

Caption

0Table1

Rear Panel Description

3Rear Panel Description A single alarm port is present in SBC 5100 platform.
This

Warning
Ribbon-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.

Note
CAT6 cabling may be required in environments where there is unusually high Electro-Magnetic interference (EMI) from power lines, manufacturing equipment, or certain types of lighting.
Caption
0	Table
1	Ethernet Port LEDs Description
3

Ethernet Port LEDs Description

pagebreak