Page History

...

1. Download the 

   Spacevars
   0 product

   artifacts install-ev.sh and ev-fullpkg.tar.xz to the /opt directory of your system.

   Info
   title Note
   For these artifacts, log in to Salesforce and open an additional browser for the Ribbon Global Software Center (GSC). In the Downloads section, search for the name and version of the required software. Reach out to  Ribbon Support for more information.

   
   

2. Enable read-write-execute permissions for the copied files using the command given below:

   Code Block
   chmod +x install-ev.sh

   
   

3. Validate installation media readiness using the command given below:

   Code Block
   pwd && ls -alh

   
   As depicted in the example screenshot, confirm the two files exhibit approximately the same size and permissions. 

4. Execute the following command to start installation process:

   Code Block
   ./install-ev.sh

   The installation continues by installing Docker Compose, Docker and

   Spacevars
   0 product

   . The GUI_IP, EV_IP, and EV_IP6 values should be set so that

   Spacevars
   0 product

    works properly.  Respond to any prompts that arise, especially the GUI_IP, EV_IP, and EV_IP6 prompt which is critical to the installation. GUI_IP, EV_IP, and EV_IP6 values must be set so that

   Spacevars
   0 product

    works properly.

   • GUI_IP - The host name or address that the users can use to access 

     Spacevars
     0 product

      from the browser's address bar.
     

     Info
     title Note
     GUI_IP must be the same as either EV_IP or EV_IP6.

     
     

   • EV_IP - The host name or IPv4 address for the managed devices to contact 

     Spacevars
     0 product

     .

   • EV_IP6 - The host name or IPv6 address for managed devices to contact 

     Spacevars
     0 product

     .
     

     Info
     title Note
     The EV_IP6 address is not set by default. If you want to access  Spacevars 0 product  using IPv6 modify the current settings and provide the EV_IP6 address.

     
     

   The installation creates a log file of all actions for historical review/troubleshooting. The resultant filename is in the format of $MM-DD-YYYY-ev-install.log 

   You are prompted to enter information related to your networking configuration. Read this section carefully and enter the appropriate values applicable to your environment.
   Once installation completes, the console screen displays the message “ 

   Spacevars
   0 product

   Installation/Upgrade Completed ”. A directory named scc-build is created.

5. To check whether the containers started successfully, use the following command:

   Code Block
   docker ps --format "table  {{.ID}}\t{{.Image}}\t{{.Status}}\t{{.Names}}"

   Tip
   title Tip
   Make sure that the STATUS is healthy. If there are unhealthy statuses, run the following command and check the Health section of the output: Code Block docker inspect $container_name For example: Code Block docker inspect scc

   
   

6. Once the installation completes, optionally run a basic sanity check using the command given below:s

   Code Block
   cd /opt/scc-build ; ./ev_check.sh post-install

7. For initial SCC configuration, register your 

   Spacevars
   0 product

   server by accessing it through the web interface at its IP address and entering the registration information that you received in your email. If the registration information is not available, reach out to Ribbon Support.

   Info
   title Note
   Refer to Manually Configure ZTP when upgrading from Spacevars 0 product  15.2.0 or 15.2.1.

   

8. Enter the 

   Spacevars
   0 product

    admin registration details, and then click NEXT.
   
9. Enter the Tenant Admin registration details, and then click NEXT.
   
10. Click APPLY to complete the registration.
    
11. Click LOGIN to navigate to the login screen.
    
12. Enter the credentials and click SIGN IN to log in to 

    Spacevars
    0 product

    .
    

...