Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Panel

In this section:

Table of Contents
maxLevel3

 

Include Page
Not_for_SWe
Not_for_SWe

Overview

This best practice document helps a user deploy and execute the Lync 2013 SBA on products that shipped from

Spacevars
0company
with the SBC 1000/2000 5.0.0 and later releases

Warning

The Lync 2013 SBA application is supported on Windows Server 2008R2 and Windows Server 2012R2 operating system. If your device does not have a license for Windows Server 2008R2, a license purchase and download will be necessary to activate and execute the Lync 2013 SBA. If a license is acquired, see Attach License Label for attaching the label on the unit. 

Note

The ASM downgraded to Lync 2013 SBA cannot be updated with a pre-6.1 ASM image, due to an incompatible driver.

Hide If
special@anonymous
matchallany
groupconfluence-users
Div
stylebackground:#EEE;border-radius:8px;display:inline-block;padding-top:3px !important;padding-bottom:3px !important;padding-left:15px !important;padding-right:15px !important;

 Please Log in to view Notes and Limitations.

Show If
special@anonymous
matchallany
groupconfluence-users

See Notes and Limitations for additional details.

Required Information

Before you begin, ensure you have the following information:

  • A SBC WebUI Credential.

Preparing the SBC and SBA

1. Upgrade the SBC and SbcComms

The firmware on the SBC as well as the firmware on the ASM (SbcComms) must be at version 5.0.2. See Upgrading or Downgrading the SBC 1000-2000 for the upgrade procedure.

2. Confirm Windows Server 2008R2 License

Confirm that your ASM is licensed for 'Windows Server 2008R2', which is a prerequisite to run Lync 2013 SBA.

To Confirm Windows Server License:

  1. Access the WebUI.
     
  2. Click the tab System.

  3. Click the tab Overview, then scroll into the ASM System Details panel.

  4. Confirm that 'Windows Server 2008R2' appears in Windows Factory License or Windows Applied Additional License.


Case 1: Your Windows factory license is 'Windows Server 2008R2'

Your license allows you to use Lync 2013 SBA already; no further licenses are required.

Panel
borderStylenone
Caption
0Figure
1 If Factory License Is Windows Server 2008R2


 

 

 

Case 2: Your Windows factory license is 'Windows Server 2012R2'

You will need to purchase and install the Windows Server 2008R2 operating system license if you want to run Lync 2013 on Windows Server 2008R2. See Working with Licenses.

 

Note

You will also need need to acquire a license to operate the Lync 2013 SBA on your ASM. See Working with Licenses. If a license is acquired, see Attach License Label for attaching the label on the unit. 

Panel
borderStylenone
Caption
0Figure
1If Factory License Is Windows Server 2012R2

 

 

3. Confirm Availability of the Lync 2013 SBA image on Windows Server 2008R2

Confirm that your ASM already has the Lync 2013 SBA image on Windows Server 2008R2 available on the hard drive.

 To Confirm Lync 2013 SBA Availability on Windows Server 2008R2:

  1. Access the WebUI.

  2. Click the tab Tasks.

  3. Under Application Solution Module, click Reinitialize.

  4. Confirm that one of the choices in the drop down menu is Lync 2013 SBA on Windows Server 2008R2.
Panel
borderStylenone
Caption
0Figure
1Confirm Availability of Lync 2013 SBA on Windows Server 2008R2


If the Lync 2013 SBA is not listed in the drop down menu, follow the instructions on Updating the ASM Recovery Partition.

Pagebreak