Page History

Name

Specifies the name of the

Indicates the system name assigned by user.

Note: If a system name is not assigned, this field displays the default system name.

Identifies whether the instances are managed manually or through the EMS.

For SBC SWe cloud deployments, two modes are supported:

• Centralized (default) - Is the traditional HA/redundancy model (1:1 scenario) where one active instance is backed up by one standby instance. In Centralized mode, the

  Spacevars
  0 product

  configuration is synchronized between active and standby

  Spacevars
  0 product

  s.
• Distributed - Is supported in

  Spacevars
  0 product

  SWe Cloud deployments where up to N active

  Spacevars
  0 product

  instances are backed up by a single standby instance (N:1). In this mode, each node is configured separately, and the configuration on active and standby instances is not synchronized. The instances in such deployments also have homogeneous configuration. In Distributed mode the lifecycle of the instances (instance spin-off, initial configuration,  delta configuration, and instance termination) is managed by the EMS and Configurator.

Location

Specifies the physical location of the

Contact

Specifies the contact information

for the

Local Authentication Enabled

Specifies

whether user information stored locally can be used for authentication.

External Authentication Enabled

Specifies

whether user information stored on

a remote RADIUS server can be used for authentication.

Util Monitor Stats Interval

Specifies the time interval for system resource monitoring statistics. The value ranges from 5 to 60 minutes and the default value is 15 minutes.

Note:  

Util Monitors Stats Num of Past Interval

Specifies the number of past intervals of data that is saved by the system resource monitoring statistics.

Audit Log State

Specifies the state of the management audit log. The options are:

• Disabled
• Enabled (default)


Dsp Mismatch Action

Specifies the action to take for

when the following DSP

mismatch conditions occur:

1. Mismatch in DSP card installation across any/all slot locations: Cards must match by slot location. For any mismatched slot, the DSP capacity is not used

1. when Preserve Redundancy is configured (and calls on the card

1. dry up if calls were already in place when the mismatch occurred), or the card is left unprotected when

1. Preserve Capacity is configured.
2. Mismatch in DSP card type within a

1. slot location: Card installations must match by type – DSP25 (higher capacity) or DSP20 (lower capacity). Same rules as above apply.

The options are:

• Preserve Redundancy (default): The

• active node automatically triggers a graceful dry-up in an attempt to align the DSP hardware capabilities. Once the dry-up process completes, the

• active node

  Spacevars
  0 product

  uses the protected, matching DSP capacity to preserve redundancy.

Note: During the dry-up period, active calls using the higher

capacity DSPs are not protected in the event that a switchover occurs before the dry-up process completes.

• Preserve Capacity: The Active

  Spacevars
  0 product

  continues to use the extra DSP capacity, as needed, assuming appropriate session licenses are in place; partial redundancy is in effect.

Note: If a switchover occurs, calls using the higher capacity DSPs on

the active are not protected during switchover (

partial redundancy).

Cli Set Warning Support

Specifies whether or not to enable warning prompts configured for the Set commands

. The options are:

• Disabled
• Enabled (default)

• False (default)

• True

If set to True and the SSH keys are populated, SSH users can log into the server without the need to enter their passwords.

• False (default)
• True

Re Key Confd Encryption Key

Use this command to regenerate encryption keys used by the system configuration database

.

Note: Sonus recommends backing up current encrypted parameters in plaintext, if possible.  Sonus further recommends performing a full configuration backup immediately after this activity has successfully completed.

Use this command as an admin user of a system (hardware server/SWe Cloud instance) to re-enable an OS account for a specific user. The CLI equivalent of this action command is request system admin <system name> reenableOsAccount userName <user name>.

For more information, refer to the Configure Accounts sub-section of the page Users and Application Management - Application Management.

Use this command to remove an instance from a Redundancy Group.

Note: This action command is applicable only for SBC SWe Cloud deployments.

Remove Saved Config

Use this command to remove a saved configuration file from the system.

• File Name – Specify filename of configuration to remove from the system.

Use this action command to configure the

the Current Value option for the other setting.

• Bond Monitoring – Select the bond monitoring type for GRHA mode.

• • Current Value 

• • Direct-connect

• • Network-connect

• Leader Election – Select the leader election algorithm type to use for GRHA mode.

• • Current Value 

• • Enhanced

• • Standard

Refer to the following pages:

• Redundancy for feature details.

• Show Table System or Show Status System for statistics details

• Enabling SBC Core Geographical Redundancy HA Mode best practice for configuration details.

Use this command to verify that the

or that the policy databases on the active and standby servers are in sync. Because these commands take a few seconds to execute,

do not

run these commands

repeatedly.

• Active And Standby Policy – Check if policy databases on the active and standby servers are in sync.

• Active Config And Active Policy – Check if the policy and configuration databases on the active server are in sync.

• All – Perform both of the above checks.

Zeroize Persistent Keys

Use this control to securely erase all persistent CSPs from the system. The