Page History

 

This section provides information on connecting media (packet) ports, HA ports, management ports, serial port and alarms ports, and installing SFPs.

Installing SFPs

Warning
SonusRibbon-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.

1 Gb SFP Transceivers

The following 1 Gb SFP transceivers are compatible with 

Spacevars
0 model5

in all Management, Media , and HA ports:

Caption
0 Table 1 1 Gb SFP Transceivers 3 1 Gb SFP Transceivers

 

10 Gb SFP Transceivers

Optionally, Pkt0 and Pkt1 (Media 0 and Media 2) can be used as a single 10 Gb port 10Gb ports using one of the in the table below, with the remaining MEDIA ports empty.

Pagebreak

Caption
0 Table 1 10 Gb SFP Transceivers 3 10 Gb SFP Transceivers

 

SFP transceivers must be installed in the Media and HA (if configured for HA) ports of each 

Spacevars
0 model5

server before making the fiber/copper connections.

• Insert the SFP Gigabit Ethernet LC or SFP Gigabit Ethernet copper RJ-45 transceivers into 

  Spacevars
  0 model5

  media ports 0-3, as needed.
• Insert the SFP Gigabit Ethernet LC or SFP Gigabit Ethernet copper RJ-45 transceivers into Management ports 0-3.Insert the SFP Gigabit Ethernet LC or SFP Gigabit Ethernet copper RJ-45 transceivers into HA ports 0-1, as needed.

Note
The router(s) connected to the Media ports MUST support Gigabit speeds. Otherwise, the Gigabit Media ports will not be able to communicate with the router(s).

Follow these steps to install SFPs for the first time:

1. Attach an Electrostatic Discharge (ESD) wrist strap (provided in the 

   Spacevars
   0 model5

   kit) using the ESD grounding point on the rear panel of the chassis (see refer to Connecting ESD Wrist Strap). 
2. Insert the SonusRibbon-approved SFP transceiver into the desired socket and ensure that the proper orientation when inserting, and you will hear a "click" sound when the SFP is latched correctly.
3. Connect/reconnect the fiber optic and/or CAT 5 cables, as appropriate, to media and HA ports.
4. Verify LEDs above the part are flashing that indicates link status and data activity.
5. Verify port functionality using the CLI show status system commands, once the SBC application software is installed and the system is up and running (for details, see show status system from the 5.0.x documentation).

   1. Verify management and packet port functionality:

      Code Block
      language none
      > show status system ethernetPort

      
      

   2. Verify HA port functionality:

      Code Block
      language none
      > show status system highAvailabilityPort

      
      

Note
If an unsupported SFP module is inserted, an error message similar to the following displays: PNPS: pkt1 SFP detected not supported by SonusRibbon! Turning pkt1 off! PNPS: Replace pkt1 SFP with an approved Sonus Ribbon part to ensure NEBS. Replace the SFP modules to resolve issue.

Note
SFP Dust Plugs from the accessory kit may optionally be installed in any un-populated depopulated SFP socket.

Connecting Serial Port

For connecting a serial cable to the serial port to communicate with a host PC, refer to the serial port connection image.

Caption
0 Figure 1 SBC Serial Port Connection

The following table lists the serial port settings for the host PC.

Caption
0 Table 1 Host PC Serial Port Settings
Serial Port Settings Value Baud 38400 Data bits 8 Stop bits 1 Parity None Flow Control None

The DB9 serial cable pin-out is shown below.

Caption
0 Figure 1 Serial Cable DB9-F to DB9-M Pin-out
Image Modified

Caption
0 Table 1 Pin and Signal Type
Pin Signal Type 1 DCD 2 RXD 3 TXD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI

Caption
0 Figure 1 Null Modem Serial Cable
Image Modified

Connecting Management Port

To establish the Management port connections, connect the CAT5e cable to the Mgmt0, Mgmt1, Mgmt2, and Mgmt3 ports. The CAT5e cable may be connected to a switch, router, LAN or WAN as per the customer requirements.

Info
title Note
The SBC 5400 management ports are permanent. The management ports use standard RJ-45 copper Ethernet connectors and are standard 10/100/1000 Mb ports.

 

Tip
title Tip
For connecting the switch ports to the management ports, Ribbon recommends the following: Enable the autonegotiation (or "autoneg") for both the connecting ports, to allow them to choose common transmission parameters, such as speed, duplex mode, and flow control. Set the advertised link modes to the following: 100 Mb Full Duplex, for SBC on hardware platforms. 1000 Mb Full Duplex, for SBC SWe.

Connecting High Availability Ports

The physical connection between two 

Spacevars
0 model5

systems consists of a pair of GIG-E cables (Use the Single mode or Multi mode fiber optic CAT5e cable (NON-CROSSOVER TYPE ONLY), directly connected between each HA ports.

The HA connections provides both box-Level and port-level redundancy system. The HA pair system consists of four management ports; two ports each per system. When a switchover occurs, the logical management address follows the currently active server. For the Media ports, the MAC and IP addresses float (are replicated from active to standby on switchover).

Caption
0 Figure 1 Management and HA Port Connections for SBC 5400
Image Modified

Note
If using fiber SFPs for HA connections, both ends of an HA connection must use the same type. Connecting a single mode SFP to a multi-mode will not work.

Connecting Alarm Ports

Note
The Alarm port is not supported by the  Spacevars 0 model5 application software in this release.

The 

Spacevars
0 model5

Alarm ports allow you to sense (Alarm In) and issue (Alarm Out) external signal. The Alarm Port utilizes a HD15 pin connector and supports 4 output alarms and 2 input alarms. You must create the remainder of the cable, wiring the appropriate sensor or alarm leads to the screw terminator on the connector.

Caption
0 Figure 1 SBC 5400 Series Alarm Ports

The following table lists the Alarm port pin details and their descriptions.

Caption
0 Table 1 Alarm Port Pin-outs
Pin Description 1 Minor Reset 2 Minor Reset Return 3 Major Reset 4 Major Reset Return 5 Critical Alarm Normally Open 6 Critical Alarm Normally Closed 7 Critical Alarm Return 8 Minor Alarm Return 9 Minor Alarm Normally Open 10 Minor Alarm Normally Closed 11 Major Alarm Normally Open 12 Major Alarm Normally Closed 13 Major Alarm Return 14 Power Alarm Normally Open 15 Power Alarm Return

Alarm Out Ports

Each Alarm Out port is a dry relay contact. Each contact will withstand up to 60 volts DC maximum when open, and will carry up to 1 ampere DC maximum when closed.

The following table lists the pin out for the Alarm Out port.

Caption
0 Table 1 Alarm Out Port Pin-outs
Pin Signal Power Out or Reset Condition 1 Alarm Out 1 Closed 2 Alarm Out 1 Return

3	Alarm Out 2	Open
4	Alarm Out 2 Return

 

5	Alarm Out 3	Open
6	Alarm Out 3 Return

 

7	Alarm Out 4	Open
8	Alarm Out 4 Return