Add_workflow_for_techpubs |
---|
AUTH1 | UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} |
---|
JIRAIDAUTH | CHORSYM-74225527 |
---|
REV5 | UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} |
---|
REV6 | UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'} |
---|
REV3 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cc7d083d, userName='null'} |
---|
REV1 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cc7d083d, userName='null'} |
---|
|
The Logical Interfaces section configures IP addresses (both IPv4 and IPv6) for the Ethernet ports and VLANs. Detailed description of the IP addresses for each of the
platforms is given below. To configure the physical layer settings and VLANs for the Ethernet ports, go to
Ports.
About Logical Interfaces -
...
SBC 1000The
supports three system created logical interfaces (known as
Ethernet 1 IP, Ethernet 2 IP, and
Ethernet 3 IP) used to hold the IP addresses of the Ethernet ports 1, 2, and 3 respectively. In addition to the system created logical interfaces, the
also supports user created VLAN logical interfaces. VLAN logical interfaces are created each time a VLAN is added to the system. See
About Logical Interfaces - VLAN Interfaces.
...
Info |
---|
Typical Skype for Business deployment where all three Ethernet ports are used: - Ethernet Port 1 to LAN
- Ethernet Port 2 to WAN network 1 (primary)
- Ethernet Port 3 to WAN network 2 (backup)
|
About Logical Interfaces -
...
SBC 2000The
supports five system created logical interfaces (known as
Administrative IP,
Ethernet 1 IP,
Ethernet 2 IP,
Ethernet 3 IP, and
Ethernet 4 IP) used to hold the IP addresses of the Admin port and each of the four Ethernet ports (see
SBC 2000 Front Panel). In addition to the system created logical interfaces, the
Sonus SBC 2000 also supports user-created VLAN logical interfaces. VLAN logical interfaces are created each time a VLAN is added to the system, and are further described in the
About Logical Interfaces - VLAN Interfaces.
...
When delivered from the factory, Ethernet 1 IP is enabled with DHCP by default, and an IPv4 IP address is acquired via a connected DHCP server. This IP address is used for performing Initial Setup on the
. See
Running Initial Setup more information. The default IP address for the logical interface named
Ethernet 2 IP is 192.168.129.2. After initial configuration, you may configure this logical interface using Settings or Tasks tabs in the WebUI.
About Logical Interfaces -
SBC SWe LiteThe
supports five system created logical interfaces (known as
Administrative IP,
Ethernet 1 IP,
Ethernet 2 IP,
Ethernet 3 IP, and
Ethernet 4 IP). In addition to the system created logical interfaces, the
Sonus SBC SWe supports user-created VLAN logical sub-interfaces.
...
Warning |
---|
The Administrative IP interface should only be used for Running Initial Setup and disconnected when not in use (especially to avoid conflicts with your network). This interface cannot be used for VOIP media or protocols, as well as all management related functionality from the web browser. |
Ethernet IP
The
system has four logical interfaces. In most deployments, one of these logical interfaces (typically
Ethernet 1 IP) is assigned an IP address used for transporting all the VOIP media packets (e.g., RTP, SRTP) and all protocol packets (e.g., SIP, RTCP, TLS). DNS servers of the customer's network should map the
system hostname to this IP address. The hostname or these IP addresses may be used by UC-enabling systems such as SIP-phones, IP-PBX and Microsoft Lync Servers and for accessing the
WebUI.
In the default software, Ethernet 1 IP is enabled and an IPv4 IP address is acquired via a connected DHCP server. This IP address is used for performing Initial Setup on the
. See
Running Initial Setup for more information. The default IP address for the logical interface named
Ethernet 2 IP is 192.168.129.2. After initial configuration, you may configure this logical interface using Settings or Tasks tabs in the WebUI.
...
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | IPv6 to IPv4 Example |
---|
|
|
|
IPv6 to IPv6 - Example
In this example, both the LAN and the WAN use IPv6. The SBC is responsible for serving as a back-to-back user agent between the two call legs. The DNS server and NTP server are both on the WAN.
Panel |
---|
|
Caption |
---|
0 | Figure |
---|
1 | IPv6 to IPv6 Example |
---|
| Image Modified |
|
IPv4 to IPv6 - Example
...
Excerpt |
---|
Info |
---|
The example below is shown for SBC 2000. |
- In the WebUI, click the Settings tab.
In the left navigation pane, go to Node Interfaces > Logical Interfaces (Networking Interfaces > Logical Interfaces. for SWe Lite) Panel |
---|
| Caption |
---|
0 | Figure |
---|
1 | Logical Interfaces - SBC 2000 Example |
---|
| Image Modified |
|
|
To view an interface's properties:
...
If the logical interface is part of a redundant ethernet Ethernet pair, several of the options on the secondary logical interface will become read-only.
Caption |
---|
0 | Figure |
---|
1 | Logical Interfaces |
---|
|
Image Removed