Versions Compared

Old Version 7

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909df, userName='null'}
JIRAIDAUTHSBX-132431
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909df, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909df, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5b09f6, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5b09f6, userName='null'}


Panel

In this section:

Table of Contents
maxLevel4



Info
iconfalse

Related articles:

Children Display



This setting is disabled by default. The options are:
Excerpt

Include Page
_SBC_does_not_support_Lync_Skype
_SBC_does_not_support_Lync_Skype

Use the NAT Traversal window to configure NAT traversal settings for SIP trunk groups. This section describes the various parameters associated with network-hosted NAT/NAPT traversal for SIP endpoints.

To View and Edit NAT Traversal Parameters

On the SBC main screen, go to Configuration > System Provisioning > Category: Trunk Provisioning > Trunk Group > SIP Trunk Group > Services > NAT Traversal. The NAT Traversal window displays.

Use the drop-down lists to select the desired Address Context, Zone and SIP Trunk Group. The Edit NAT Traversal window displays.



Use Reference the following parameters table to configure when configuring the NAT traversal settings for the trunk group, and then click Save.

The values are: inter-working Webrtc , WRTC .Ice Lync – This is used when inter-working with a Microsoft Lync 2010 or 2013 client.For MS Lync ICE (Ice Lync setting), keep-alive messages are sent only to the RTP port.Specifies the keep alive timer in full-ICE and MS-Lync ICE. The value ranges from 0 to 60 seconds and the default value is 15 secondsNoteThe Ice Keepalive Timer appears only when the Ice Support flag is set to  Full or Ice Lync.IceUse this flag to specify if SBC initiates the TCP connection for ICE Lync Passive ) – The SBC waits for the peer to initiate the TCP connection. Use this option when working directly with Lync endpoints.
  • Active –  Use this option for the SBC to initiate the TCP connection when connected to internal-facing trunk groups where the peer is not behind the NAT. Also, use this option when working with certain Unified Communication (UC) servers such as Acano which expect the peer to initiate the TCP connection. This is only supported when there are no NATs between the SBC and the UC server.

    • Parameter

    Length/Range

    Description

    Signaling NAT

    N/A

    Indicates whether or not NAT/NAPT support is required for signaling. 

    • Disabled (default)
    • Enabled

    Include Page
    _No_NAT_for_IPv6
    _No_NAT_for_IPv6

    Media NAT

    N/A

    Specifies whether or not NAT/NAPT support is required for media. 

    • Disabled (default)
    • Enabled
    Info
    titleNote

    Do not configure Media NAT and Ice Support flags on the same trunk group.

    Include Page
    _No_NAT_for_IPv6
    _No_NAT_for_IPv6

    Learn NAT For Rtp Only

    N/A

    Enable flag to learn media NAT from the first RTP packet only. If disabled, media NAT is learned from any first packet received. For egress trunk groups, this flag is applicable only if Dynamic LRBT flag is disabled. If Dynamic LRBT is enabled, NAPT learning occurs on arrival of RTP packet until the call is connected, at which point Learn NAT For Rtp Only applies applies even for egress Trunk Groups. The options are: 

    • Disabled (default) 

    • Enabled

    Info
    titleNote

    The action of this flag does not apply to ICE NAT traversal.


    Ice Support

    N/A

    This parameter indicates the type of Interactive Connectivity Establishment (ICE) method used for STUN packet check.

    • Ice Webrtc – Use this setting when

    • interworking with

    • WebRTC Gateways

    • ; for example, with the Ribbon

    • WebRTC Gateway or in situations when the SBC is presented with an ICE SDP from a WebRTC-enabled endpoint.

    Info
    titleNote

    When configured for this mode, the SBC acts as a generic ICE-Lite agent

    .

    • Ice Full – This is used when inter-working with a full ICE client which requires a STUN connectivity check to be generated by the SBC in response to its own STUN connectivity check
    Info
    titleNote
    • .

    Include Page
    _ICE_note
    _ICE_note

    Info
    titleNote

    The parameter, Learn NAT For Rtp Only, does not apply to ICE and should not be enabled for a Trunk Group with ICE Support enabled.


    Warning

    The SBC's ICE support capability is not supported for GW-GW call scenarios.

    Refer to SDP Support for a detailed description on Ice Support

    		Ice Keepalive Timer

    .

    Info
    title

    Ice Trickle

    N/A


    Multiexcerpt
    MultiExcerptNameTrickle ICE definition

    Trickle ICE is a mechanism that allows ICE agents to shorten session establishment delays by making the candidate gathering and connectivity checking phases of ICE non-blocking and by issuing them in parallel. This allows starting the call setup procedure to the SBC before all candidates have been gathered by the user agent so that additional candidates can be sent to the SBC in subsequent INFO and/or offer and answer messages.

    Use this flag to enable Trickle ICE support for this trunk group.

    • Disabled (default)
    • Enabled
    Include Page
    _Trickle_Ice_Warning
    _Trickle_Ice_Warning

    TCP Keepalive Timer

    15-65535

    This NAT TCP keep-alive timer sets the registration refresh rate (in seconds) for SIP over TCP.

    (default = 240).

    UDP Keepalive Timer

    15-65535

    This NAT UDP keep-alive timer sets the registration refresh rate (in seconds) for SIP over UDP.

    (default = 60).

    Outbound TCP Keepalive Timer

    0-32767

    The Specifies the NAT outbound keepalive timer (in seconds) for SIP over TCP . The value ranges from 0 to 32767 and the default value is 240.for SIP outbound-supported UAs (RFC 5626).

    (default = 240) 

    Outbound UDP Keepalive Timer

    0-32767

    The Specifies the NAT outbound keepalive timer (in seconds) for SIP over UDP . The value ranges from 0 to 32767and the default value is 60.for SIP outbound-supported UAs (RFC 5626).

    (default = 60) 

    Secure Media NAT Prefix

    		0-32

    Use this parameter to match up to 'N' bits of the network IPv4 address obtained from signaling. If set to "0", feature is disabled, and no match of network IP address will occur

    .  The value ranges from 0 to 32 and the default value is 0.    		Ice TCP Role

    .

    (default

    = 0)

    Info
    titleNote

    Ice TCP Role appears only when the Ice Support flag is set to Ice Full or Ice Lync.

    		Disable Media NAT If Same Media And Sig IP

    N/A

    Enable this flag to disable Media NAT if Media and Signaling IP addresses are identical.

     

    • Disabled (default)
    • Enabled