Page History

Panel

In this section:

Table of Contents

maxLevel	2
minLevel	2

Info

icon	false

BCI

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes bci 
	bciInterworkEncountered <disable | enable> 
	bciIsdnAddess <disable | enable>

Command Parameters

Caption

0	Table
1	BCI Parameters

...

Parameter Description

bci

Use this object to configure Backward Call Indicator (BCI) for Egress IP attributes.

bciInterworkEncountered – Enable flag to indicate that ISUP is interworking with a network which is not capable of providing as many services as ISUP does. ISUP networks will therefore not employ certain features they otherwise normally would, including potentially the use of ISDN cause codes in failure conditions .
- disable (default)
- enable
bciIsdnAddess – Enable flag to enable ISDN Address in the BCI parameter of backward SS7 messages (e.g. ACM or ANM).
- disable (default)
- enable

Domain Name

Use this object to specify use of domain names.

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes domainName 
	useIpSignalingPeerDomainInRequestUri <disable | enable>
	useSipDomainInPAIHeader <disable | enable>
	useSipDomainNameInFromField <disable | enable> 
		preserveIngressFromDomainName <disable | enable> 
		useLowerCaseDomainNames <disable | enable> 
	useSipDomainNameInRequestUri <disable | enable> 
		preserveIngressRUriDomainName <disable | enable> 
		useLowerCaseDomainNames <disable | enable> 
	useZoneLevelDomainNameInContact <disable | enable>

...

	useZoneLevelDomainNameInPathHdr <disable | enable>

Command Parameters

Caption

0	Table
1	Domain Name Parameters
3	Domain Name Parameters

...

Parameter

Description

useIpSignalingPeerDomainInRequestUri

Enable this flag to use IP Signaling Peer Domain in Request URI.

disable (default)
enable

...

Spacevars

0	product

...

useSipDomainInPAIHeader

Enable this flag to set the value of the host port of the

...

PAI URI equivalent to the value of the SIP domain name configured on the ingress trunk group of the Policy Exchange Server (PSX).

disable (default)
enable

useSipDomainNameInFromField

By default, the

Spacevars

0	product

uses its IP address as the host-port of the FROM URI in the outgoing INVITE message. Enable flag to use the originating gateway information returned in the policy response as the host-port of the FROM URI in the outgoing INVITE message.

disable (default)
enable

When useSipDomainNameInFromField is enabled, the following

...

flags are available:

preserveIngressFromDomainName – If a SIP domain is configured for the ingress trunk group and this flag is enabled, the default gateway associated with that SIP domain will be the originating gateway. Otherwise, the originating gateway will be the default gateway associated with the SIP domain associated with the Softswitch entity.
- disable (default)
- enable

useLowerCaseDomainNames – Set flag to allow lower case domain name.
- disable (default)
- enable

...

NOTE: The above two flags only apply when a

...

Domain Name is configured for this zone (

...

refer to Zone - CLI

...

).

useSipDomainNameInRequestUri

Use this flag to indicate how to treat SIP Domain name in outgoing SIP INVITE.

disable

...

– The
Spacevars
0 product
includes the IP address in the host-port portion of the Request-URI in outgoing SIP INVITE messages.
enable – The
Spacevars
0 product
includes the trunk group domain associated with egress trunk group as destination domain name in outgoing SIP INVITE messages.

When useSipDomainNameInRequestUri is enabled, the following parameters are available:

preserveIngressRUriDomainName – Preserve Ingress R-URI Domain Name Flag. When enabled, the ERE/
Spacevars
0 product
uses domain name received in the Request-URI as destination domain name in outgoing SIP INVITE messages. Normally, outgoing SIP INVITE messages contain the trunk group domain assigned to egress trunk group.
- disable (default)
- enable
useLowerCaseDomainNames – Set flag to allow lower case domain names.
- disable (default)
- enable

useZoneLevelDomainNameInContact

Enable this flag to use Zone level domain name in the Contact header.

disable (default)
enable

useZoneLevelDomainNameInPathHdr

Enable this flag to send the Domain Name configured at the Zone level in the Path Header of the outgoing REGISTER message.

disable (default)
enable

Flags

Use this object to set egress IP attribute flags.

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes flags
	addLoopBackRouteHeader <disable | enable>
	bgcfTargetSchemeTransparency <disable | enable>
	convertInactiveToSendrecv <disable | enable> 
	disable2806Compliance <disable | enable> 
	disableOptionalRegisterParameters <disable | enable>
	ignoreSdpAfterOfferAnswerCompleted <disable | enable>
	includeEnumParameters <disable | enable>
	map3xxContactUrlToRouteHeader <disable | enable>
	map181Or182MessageTo183 <disable | enable> 
	mapContractorNumberInPSigInfoHeader <disable | enable>
	monitorRtpOnEgressUpdate <disable | enable>
    qosBasedRouting <disable | enable> 
	sameCallIdForRequiredAuthorization <disable | enable>
	suppressUnregister <disable | enable>
	transitPAIFromUnregisteredPeer <disable | enable>
	ttcIsupMapping <disable | enable> 
	useCalledPartyInRequestUri <disable | enable> 
	useColonInSdpMediaTypeParameter <disable | enable> 
	validateIsubAddress <disable | enable>

Command Parameters

Caption

0	Table
1	Flags Parameters
3	Flags Parameters

...

Parameter Description

addLoopBackRouteHeader

Enable flag to add the SBC URI as the second top-most Route header in the INVITE towards EATF.

disable (default)
enable

bgcfTargetSchemeTransparency

Enable flag to preserve the scheme used by the SIP INVITE Request-URI when the INVITE is routed by the

Spacevars

0	product

, acting as a BGCF supporting Tel-URL. When disabled, the SBC changes the scheme used by the Request-URI parameter to SIP in the egress INVITE message.

disable (default)
enable

convertInactiveToSendrecv

Enable flag to control the a-line in the SDP of an egress SIP INVITE message by converting a=inactive to a=sendrecv. When disabled, the

Spacevars

0	product

continues to use a=inactive, when appropriate, in the egress INVITE message.

disable (default)
enable

disable2806Compliance

If enabled, the 2806 Compliance Code is disabled and no phone context or user=phone parameters are signaled in egress messages.

disable (default)
enable

disableOptionalRegisterParameters

Enable flag to prevent

Spacevars

0	product

from sending the DTG (Destination Trunk Group) parameter in the Contact header of egress REGISTER messages.

disable (default)
enable

ignoreSdpAfterOfferAnswerCompleted

Enable flag to allow the SBC to ignore the new SDP at the egress leg in subsequent 1xx-rel or final 200 OK messages after the Offer Answer for the initial Invite dialog was completed by an earlier 1xx-rel (and does not trigger a new offer or answer).

disable (default)
enable

includeEnumParameters

Use this flag to specify how to handle ENUM parameters in outgoing INVITE.

disabled (default) – SBC drops ENUM parameters received from ENUM server.
enabled – SBC sends ENUM parameters in the outgoing INVITE

map3xxContactUrlToRouteHeader

When map3xxContactUrlToRouteHeader flag is enabled, SBX adds 3XX contact header as second route header in the outgoing INVITE message.

This flag is enabled on a IBCF TG because when a call is routed by ECSCF to IBCF, the 3xx contact URI need to be added as second route header for subsequent routing to IP-PSAP.

disable (default)
enable

map181Or182MessageTo183

Enable flag to allow

Spacevars

0	product

to map 181 or 182 response messages to 183. When disabled, the SBC handles 1xx response messages normally.

disable (default)
enable

mapContractorNumberInPSigInfoHeader

Enable flag to map the Contractor Number parameter into the outgoing SIP P-Sig-Info header. The P-Sig-Info header is a customer-specific SIP header used to convey ISUP information in SIP messages.

disable (default)
enable

monitorRtpOnEgressUpdate

This flag is used to decide whether to start tone and monitor RTP or not.

disable (default)
enable

qosBasedRouting

Enable flag to allow QoS-based routing.

disable (default)
enable

sameCallIdForRequiredAuthorization

...

Enable this flag to support sending an INVITE with credentials on receiving a 401 (Unauthorized) or 407 (Proxy Authentication Required) response to initial INVITE with the same call ID as in the original INVITE.

disable (default)
enable

...

NOTE: To view and configure this flag, you must first enable both 'authCodeHeaders' transparency flag and 'statusCode4xx6xx' relay flag. Refer to Transparency Flags - CLI and Relay Flags - CLI for additional details.

suppressUnregister

Enable flag to prevent

Spacevars

0	product

from sending an unregister message (Register=0) to the registrar upon expiration of a SIP UA registration. When disabled, the

Spacevars

0	product

generates unregister messages on the egress leg if the UA does not refresh the registration on time.

disable (default)
enable

transitPAIFromUnregisteredPeer

Enable flag to transparently pass the received PAI to the INVITE

...

if the default PUI procedure cannot add a PAI header.

disable (default)
enable

...

NOTE: To use this flag, you must enable the enableDefaultPUIProcedures flag and disable the '

...

privacy transparency' flag (See

...

Privacy section below).

ttcIsupMapping

When enabled, and when the IP protocol type of the IP signaling profile entry is SIP or SIP-I, the application that receives the

Spacevars

0	product

policy response (which can be either the SIP signaling gateway application on the

Spacevars

0	product

or the SIP core proxy on the

Spacevars

0	product

) applies the mapping necessary for TTC-ISUP signaling.

disable (default)
enable

useCalledPartyInRequestUri

When enabled, the

Spacevars

0	product

copies the username selected for the "To" header to the Request URI instead of the registered username. When disabled, the

Spacevars

0	product

includes the registered username in the Request URI. This flag is used when interoperating with IP-PBXs that require the real end station number in the Request URI in order to do proper routing of calls terminating on them.

disable (default)
enable

useColonInSdpMediaTypeParameter

When enabled, a colon (:) is used as the separator between the SDP Media Type parameter key and value. When disabled, an equal sign (=) is used as the separator between the SDP Media Type parameter key and value.

disable (default)
enable

validateIsubAddress

When enabled, the

Spacevars

0	product

validates ISUB digits for called and calling parties. When isabled, the

Spacevars

0	product

will not validate ISUB digits.

ISUB

Use this object to configure ISDN Calling Party Subaddress (ISUB) parameters:

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes isub 
	allowNsapIsub <disable | enable> 
	allowUserSpecifiedIsub <disable | enable> 
	includeCalledPartyIsub <disable | enable> 
	includeCallingPartyIsub <disable | enable>

Command Parameters

Caption

0	Table
1	ISUB Parameters
3	ISUB Parameters

...

Parameter	Description
`allowNsapIsub`	Enable to allow NSAP ISUB parameter. `disable` (default) `enable`
`allowUserSpecifiedIsub`	Allow user-specified ISUB. `disable` (default) `enable`
`includeCalledPartyIsub`	Include called party ISUB. `disable` (default) `enable`
`includeCallingPartyIsub`	Include calling party ISUB. `disable` (default) `enable`

Media QOS KPI Profile

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes mediaQosKpiProfile <profile_name>

Command Parameter

Caption

0	Table
1	Media QOS KPI Profile Parameter
3	Media QOS KPI Profile Parameters

...

Parameter	Description
`mediaQosKpiProfile`	The Media QoS KPI (Key Performance Indicator) Profile name.

Number Globalization Profile

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes numberGlobalizationProfile <profile_name>

Command Parameters

Caption

0	Table
1	Number Globalization Profile Parameter
3	Number Globalization Profile Parameter

...

Parameter	Description
`numberGlobalizationProfile`	The Number Globalize Profile name. This profile converts numbers to SIP global number format.

Number Portability Attributes

Number portability attributes configuration.

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes numberPortabilityAttributes 
	disableRn <disable | enable> 
	npdiOptions <doNotIncludeNpdi | includeNpdi | includeNpdiYes>

Command Parameters

Caption

0	Table
1	Number Portability Attributes Parameters
3	Number Portability Attributes Parameters

...

Parameter Description

disableRn

Enable flag to prevent the

Spacevars

0	product

and ERE SIP proxy/redirector from sending the SIP rn parameter in the egress INVITE message when an LNP translated number is present. When the flag is disabled, the

Spacevars

0	product

and ERE SIP proxy/redirector send "rn=NNNN" in the userinfo portion of the Request URI, where "NNNN" is the LNP translated number.

disable (default)
enable

npdiOptions

Use the following options to specify whether the

Spacevars

0	product

and ERE SIP proxy/redirector send the SIP NPDI parameter in the egress INVITE message when LNP translation is performed by ERE call processing or the preceding switch.

doNotIncludeNpdi – Do not send the NPDI parameter.
includeNpdi – Send "npdi" in the userinfo portion of the Request URI.
includeNpdiYes – (default) Send "npdi=yes" in the userinfo portion of the Request URI.

P-Charge Info

Use this parameter to configure egress P-Charge-Info header in INVITE message behavior.

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes pChargeInfo
	includeNOA <disable | enable>
	includeNPI <disable | enable>
	pChargeInfoTransparency <disable | enable>
	pChargeInfoType <headerParameter | uriParameter | userParameter>

Command Parameters

Caption

0	Table
1	P-Charge Info Parameters
3	P-Charge Info Parameters

...

Parameter	Description
`includeNOA`	Enable flag to include Nature of Address Indicator in egress P-Charge-Info header in INVITE message. `disable` (default) `enable`
`includeNPI`	Enable flag to include Number Plan Indicator in egress P-Charge-Info header in INVITE message. `disable` `enable` (default)
`pChargeInfoTransparency`	Enable flag to transparently pass egress P-Charge-Info header in INVITE message. `disable` (default) `enable`
`pChargeInfoType`	The format types for which NPI/NOA are encoded in P-Charge-Info header. Options include: `headerParameter` – NPI and NOA are sent in header parameter format. For example, P-Charge-Info: <sip:123456@10.54.69.140>;npi=ISDN;noa=3 `uriParameter` (default) – NPI and NOA are sent in uri parameter format. For example, P-Charge-Info: sip:123456@10.54.69.144;npi=ISDN;noa=3 `userParameter` – NPI and NOA are sent in user info parameter format. For example, P-Charge-Info: <sip:12345;npi=ISDN;noa=3@10.54.69.144>

Phone Context Parameter Length

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes phoneContextParameterLength (0-31)

Command Parameter

Caption

0	Table
1	Phone Context Parameter Length Parameters
3	Phone Context Parameter Length Parameters

...

Parameter Length/Range Description

phoneContextParameterLength

0-31

Use this attribute to specify the length of phone-context parameter sent in RURI and To headers of the egress message (default = 0).

When a value greater than "0" is configured, and the called number is globalized using the existing globalization profile, the PSX sends the configured value in a policy response to the

Spacevars

0	product

. The

Spacevars

0	product

uses this configured value to insert phone-context parameter of received length in RURI and To headers.

Anchor
Privacy
Privacy
Privacy

Use this object to specify Privacy parameters.

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes privacy
	anonymizeHostIpPortion <disable | enable>
	flags 
		includeEmbeddedPAIheaderInRedirectedInvite <disable | enable> 
		includePrivacy <disable | enable> 
		msLyncPrivacySupport <disable | enable> 
		privacyRequiredByProxy <disable | enable> 
	privacyInformation 
			<pAssertedId | pPreferredId | remotePartyId> 
	transparency <disable | enable>

Command Parameters

Caption

0	Table
1	Privacy Parameters
3	Privacy Parameters

...

Parameter	Description

...

Privacy flags:

...

disable (default)
enable

anonymizeHostIpPortion

When the flag is set to enable, the

Spacevars

0	product

...

anonymizes the incoming host IP portion of the private headers (P-AID, P-PID, RPID) by replacing it with the IP address of the

Spacevars

0	product

...

Spacevars

0	product

...

before sending it to the egress leg of a call.

disable (default)
enable

Note: This flag is available for configuration only when the transparency flag (below) is enabled. For more information on Privacy Transparency of Egress IP Attributes, see Privacy section.

This feature supports in-dialog messages only, plus the following message types:

INVITE
BYE
OPTIONS
SUBSCRIBE
NOTIFY
UPDATE
PUBLISH
MESSAGE

flags

Privacy flags:

includeEmbeddedPaiHeaderInRedirectedInvite – Enable this flag to include the embedded PAI header in the redirected Invite message.
- disable (default)
- enable
includePrivacy – Use this flag to specify whether the SBC includes privacy information in outgoing SIP INVITE messages.
- disable – The
  Spacevars
  0 product
  does not include a P-Preferred-Identity header or a P-Asserted-Identity header, an Anonymous identifier in the SIP From field, or a Privacy header that contains a Critical token in outgoing SIP INVITE messages, and the
  Spacevars
  0 product
  will not include a P-Asserted-Identity header or a Privacy header that contains a Critical token in outgoing SIP INVITE messages.
- enable (default) – The
  Spacevars
  0 product
  includes either a P-Preferred- Identity header or a P-Asserted-Identity header (provisioned in Privacy Information above) in outgoing SIP INVITE messages. The
  Spacevars
  0 product
  will include a P-Asserted-Identity header in outgoing SIP INVITE messages. The
  Spacevars
  0 product
  will also insert an Anonymous identifier in the SIP From field and the
  Spacevars
  0 product
  will include a Privacy header that contains a Critical token.
msLyncPrivacySupport – Backward compatibility for the Caller Privacy feature. The Caller privacy feature only works if this flag is enabled.
- disable (default)
- enable
privacyRequiredByProxy – Enable flag to indicate that privacy service is mandated for any calls to the SIP trunk (proxy). In this case, the
Spacevars
0 product
includes a Proxy-Require header with a privacy value, and a critical token in the Privacy header of the INVITE message. The privacy service must be applied by the proxy or the call is rejected. If disabled, the
Spacevars
0 product
does not include a Proxy-Require header with privacy value. The proxy accepts the call even if it cannot provide privacy service.
- disable (default)
- enable

privacyInformation

Use this object to specify which of the following headers the

Spacevars

0	product

uses when sending privacy information in outgoing SIP INVITE messages:

pAssertedId – Used among trusted SIP entities (typically intermediaries) to carry the identity of the caller as it was verified by authentication.
pPreferredId – Used by a User Agent (UA) to carry the identity the caller wishes to be used, and sent to a trusted proxy to be inserted in the P-Asserted-Identity field.
remotePartyId – Used among trusted SIP entities (typically intermediaries) to carry the identity of the caller as it was verified by authentication. This header is specified in an earlier RFC that continues to be supported.

transparency

Enable flag to allow ingress Privacy information to pass through unchanged.

disable (default)
enable

Redirect

Use this object to configure Redirect parameters.

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes redirect 
	contactHandling <mergeReceivedContacts | purgeExistingContacts> 
	flags 
		forceRequeryForRedirection <disable | enable>
		honorEmbeddedHeadersin3xx <disable | enable>
		relayUnusedContactParams <disable | enable>
		skipCrankbackProfileAndAlwaysCrankback <disable | enable> 
	mode <acceptRedirection | allowSingleRedirectAttempt | rejectRedirection>

Command Parameters

Caption

0	Table
1	Redirect Parameters
3	Redirect Parameters

Parameter Description

contactHandling

Select one of the following to control processing of contacts received in SIP Redirects:

mergeReceivedContacts – Contacts received in Redirects are ordered by q-value and inserted at the head of the list of untried contacts.
purgeExistingContacts – Contacts received in Redirects are ordered by q-value and replace untried contacts.

flags

Redirect flags:

forceRequeryForRedirection – (applies to Invite requests only) Use flag to re-query ERE with contact information received in a 3xx response for redirection-type scenarios.
- disable (default)
- enable
honorEmbeddedHeadersin3xx –Enable flag to allow the processing of embedded headers in 3xx Contact headers for the trunk group that received the 3xx. disable (default) enable
relayUnusedContactParams – When enabled, Contact parameters received in 3xx responses that are not consumed/processed locally by the SBC (see NOTE below) can now be passed through to the R-URI of subsequent INVITE request.
- disable (default)
- enable
skipCrankbackProfileAndAlwaysCrankback – Enable this flag to force any 4xx–6xx SIP response code to cause crankback so the next potential contact or 3xx response is tried. If disabled, only the response codes specified in default SBC crankback profile cause the call to crank back.disable (default) enable

mode

Use this object to control SIP redirection:

acceptRedirection (default)– Multiple redirections are allowed.
allowSingleRedirectAttempt – Only a single Redirect is allowed per route. Additional Redirects cause crankback to be performed.
rejectRedirection – If a Redirect is received, crank back is performed.

...

Info

...

title

...

Note

Parameters consumed/processed locally by the

...

Spacevars

0	product

and excluded from relayUnusedContactParams command include:

dtg
tgrp
trunk-context
cic
npdi
npi
rn
bgid
bgt
user
phone-context

...

Back to Top

Signaling QOS KPI Profile

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes signalingQosKpiProfile <profile_name>

Command Parameter

Caption

0	Table
1	Signaling QOS KPI Profile Parameters
3	Signaling QOS KPI Profile Parameter

...

Parameter	Description
`signalingQosKpiProfile <profile name>`	The Signaling QoS KPI (Key Performance Indicator) Profile name.

SIP Cause Mapping

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <IPSP name> egressIpAttributes sipCauseMapping 
	sipToInternalCauseMappingProfileName <sipToInternalProfile_Name>
	internalToSipCauseMappingProfileName <internalToSIPProfile_Name>

Command Parameters

Caption

0	Table
1	SIP Cause Mapping Parameters
3	SIP Cause Mapping Parameters Parameters

...

Parameter

Description

sipCauseMapping

Use this object in a SBC ERE configuration to create Internal-to-SIP and SIP-to-Internal SIP Cause Mapping Profile names for this IP Signaling Profile.

internalToSipCauseMappingProfileName– The name of the Internal-to-SIP cause mapping profile.
sipToInternalCauseMappingProfileName – The name of the SIP-to-Internal cause mapping

...

profile.

Info

To create a profile to map CPC and SIP, refer to CPC to SIP Cause Map Profile - CLI and SIP CPC Cause Code Mapping Profiles - CLI.

To associated these profiles with Ingress/Egress trunk groups, refer to

...

SIP Trunk Group - Signaling - CLI.

For configuration examples and external PSX considerations,

...

refer to Configuring SIP Cause Code Mapping.

...

SIP Headers and Parameters

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes sipHeadersAndParameters 
	callForwarding 
		dataMapping <diversion | none | pkHeader> 
		diversionHeaderTransparency <disable | enable> 
		diversionHistoryInfoInterworking <disable | enable>
		historyInformation 
			includeHistoryInformation <disable | enable>
				causeParameterInRFC4458 <disable | enable> 
				reasonWithCauseValueAsPerRFC4244 <disable | enable>
 	destinationTrunkGroupOptions <includeDtg | includeNone | includeTgrpWithDomainName | includeTgrpWithIpAddress>
	flags 
		endToEndAck <disable | enable>
		includeCic <disable | enable> 
		includeCpcInformation <disable | enable> 
		includeNpi <disable | enable> 
		includeOlip <disable | enable> 
		includePKAdn <disable | enable> 
		includePstnParameters <disable | enable> 
		includeQvalue <disable | enable> 	
		skipCSeqCheckInEarlyDialog <disable | enable> 
		transparencyForDestinationTrunkGroupParameter <disable | enable>
	generateCallIdUsing <doNotUseIngressCallId | useIngressCallIdByAddingStaticString | useIngressCallIdByPrepending>
	includeChargeInformation <includeNone | includePChargeInfo> 
	originatingTrunkGroupOptions <includeNone | includeOtg | includeTgrpWithDomainName | includeTgrpWithIpAddress>
   	sessionExpiresRefresher

...

<notSend | uac | uas>
    sipToHeaderMapping <calledNumber | gapDialedNumber | none | originalCalledNumberOcn>

Command Parameters

Div

class	pdf6pttext

Caption

0	Table
1	sipHeadersAndParameters Parameters
3	sipHeadersAndParameters

...

Parameter

Description

callForwarding

This parameter is used to control the call forwarding data mapping method in egress SIP signaling.

dataMapping – Use this parameter to define how to map the diversion or redirecting data. Options are:
- none – No Diversion information is egressed.
- diversion – Diversion information is sent out as SIP Diversion Header.
- pkHeaders – Diversion information is sent out as proprietary PK Headers.
diversionHeaderTransparency – When enabled, the ingress Diversion header is passed through unchanged. Call forwarding data mapping transparency applies to Diversion header only
- disable (default)
- enable
diversionHistoryInfoInterworking – Enable flag to allow interworking between Diversion and History-Info header as per RFC 6044. The
Spacevars
0 product
supports up to 12 History-Info entries and 10 Diversion entries. When this flag is disabled, only the first and last entries are maintained when History-Info or diversion transparency is disabled.
- disable (default)
- enable

...

- NOTE: This flag is only visible when either Diversion or History-Info header is selected as the egress call forwarding header. Diversion and History-Info Transparency configuration controls are ignored when it is enabled. This parameter has precedence over the others.

historyInformation includeHistoryInformation – Use this parameter to specify how to treat call forwarding history information. Enable this flag to include History-Info in INVITE egress message.
- disable (default)
- enable
- causeParameterInRFC4458 – Enable this flag to include the History-Info cause value in egress message as per RFC 4458 recommendation. When the flag is enabled, the output is similar to the following example:
  History-Info: <sip:1234567890@P1.interwork.com?Privacy=none>;index=1, <sip: last_diverting_target;cause=408>;index=1.1
  - disable (default)
  - enable
- reasonWithCauseValueAsPerRFC4244 – Enable this flag to include History-Info cause value with Reason Header as per RFC 4244 recommendation. When the flag is enabled, the output is similar to the following example:
  History-Info: <sip:1234567890@P1.interwork.com?Privacy=none>;index=1, <sip: last_diverting_target?Reason=SIP%3Bcause%3D408>;index=1.1
  - disable (default)
  - enable

destinationTrunkGroupOptions

Use this parameter to specify destination trunk group options.

includeDtg – Include the destination trunk group parameter in SIP headers sent over associated trunk group.
includeNone (default) – Do not include any trunk group information.
includeTgrpWithDomainName – Include trunk group with domain name.
includeTgrpWithIpAddress – Include the destination trunk group, and include the trunk context as domain name.

flags

Use this object to configure the SIP Headers and Parameters flags.

endToEndAck – Enable flag to send the ACK towards egress for the initial invite after receiving it from the ingress (remote) entity. The application retransmits the 200 OK towards the ingress side based on the configuration, and terminates the call if no ACK is received for the corresponding 200 OK.
- disable (default)
- enable
includeCic – If enabled, the
Spacevars
0 product
includes the Carrier Identification Code in a cic= parameter in outgoing INVITE messages.
- disable (default)

...

- enabl
includeCpcInformation – If enabled, the
Spacevars
0 product
includes the Calling Party Category (CPC) parameter value in the From header of outgoing SIP INVITE messages.The CPC parameter characterizes the station used to originate a call, such as ordinary, priority, data, test, operator, pay phone, prison, hotel or unknown.
- disable (default)
- enable

includeNpi – If enabled, the
Spacevars
0 product
includes the Numbering Plan Indicator in a npi= parameter in outgoing INVITE messages.
- disable (default)
- enable
includeOlip – If enabled, the
Spacevars
0 product
includes the Originating Line Information Parameter in a oli= parameter in outgoing INVITE messages.
- disable (default)
- enable
includePKAdn – When enabled, the
Spacevars
0 product
includes the P-K-Adn header in egress SIP messages. When disabled, the
Spacevars
0 product
does not include the P-K-Adn header. The P-K-Adn header is a customer-specific SIP header used for ISUP-to-SIP interworking and contains the Translation Source Number (TSN) used in Number to SIP URL translation via the Number Username Translation screen (Generic variant only).
- disable (default)
- enable
includePstnParameters – If enabled, the
Spacevars
0 product
includes a set of specific PSTN parameters in a pstn-params= entry in outgoing INVITE messages. The PSTN parameters currently included in pstn-params are Screening Indicator, ISDN Indicator, and Transmission Medium Requirement (TMR).
- disable (default)
- enable
includeQvalue – If enabled, the ERE SIP proxy/redirector includes the qvalue parameter (for example, q=0.9) in the Contact header of outgoing 3xx messages.
- disable (default)
- enable
skipCSeqCheckInEarlyDialog – When enabled, the
Spacevars
0 product
accepts multiple SIP requests in which the CSeq number in a later request is of a lesser value than the CSeq number received in earlier requests.
- disable (default)
- enable
transparencyForDestinationTrunkGroupParameter – When enabled, if ERE receives both tgrp parameter and trunk-context in an ingress INVITE Request-URI, ERE as proxy transparently passes the tgrp parameter and trunk-context in the egress INVITE Request-URI. Values selected for the "Destination Trunk Group Option" are ignored.
- disable (default)
- enable

generateCallIdUsing

Use this parameter to control ingress and egress Call-ID behavior.

doNotUseIngressCallId – Generates egress Call-ID independent of ingress Call-ID.
useIngressCallIdByAddingStaticString – Generates egress Call-ID using ingress Call-ID and a static string (egressCallIdStaticString) configured in the SIP trunk group.
Egress Call-ID is the aggregate of ingress Call-ID and static string.
useIngressCallIdByPrepending – Generates egress Call-ID using ingress Call-ID and locally generated string. Egress Call-ID is the aggregate of ingress Call-ID and locally generated string.

includeChargeInformation

Select the includePChargeInfo option to map charge information in a call setup message (i.e., the charge number parameter of an IAM) to egress P-Charge-Info header in INVITE message. If the ERE returns billing information in a policy response, the

Spacevars

0	product

ensures that the egress P-Charge-Info header in INVITE message is populated with the indicated data. If the

Spacevars

0	product

receives a SIP INVITE message for a call destined to the PSTN, the

Spacevars

0	product

populates the charge number parameter of the outgoing IAM based on the egress P-Charge-Info header in INVITE message.

includeNone (default)
includePChargeInfo

originatingTrunkGroupOptions

Use this parameter to specify originating trunk group options.

includeNone (default) – Do

...

not include any trunk group information. `includeOtg` – Include the originating trunk group parameter in SIP headers sent over the associated trunk group. `includeTgrpWithDomainName` – Include the originating trunk group, and include the trunk context as domain name. `includeTgrpWithIpAddress` – Include the originating trunk group, and include the trunk context as IP address
`sessionExpiresRefresher`	Controls whether the refresher parameter

...

is sent in the Session-Expires header and is enabled when the Customized Session Timer Behavior flag is selected. Options include:

notSend (default) – The Session-Expires refresher parameter is not sent in the initial outgoing INVITE message, re-INVITE message, and UPDATE message.
Uac – When selected, the parameter refresher uac (User-Agent Client) is sent in the Session-Expires header.
Uas – When selected, the parameter refresher uas (User-Agent Server) is sent in the Session-Expires header.

...

sipToHeaderMapping

This parameter indicates which number is mapped and returned in the outgoing SIP To header. Options include:

calledNumber – The TO header is mapped using the called number.
gapDialedNumber – The TO header is mapped using the Generic Address Parameter from mime, if applicable.
none (default) – The TO header user part is mapped from the Original Called Number, if present. Otherwise, it is mapped from the Called Number. The Original Called Number may be taken from the Diversion or the History-Info header, if present, in a SIP Invite.
originalCalledNumberOcn – The TO header is mapped using the redirecting original Called number OCN parameter. This is filled from the SIP Invite using the Diversion or the History-Info header, if present.

...

Back to Top

Transport

Command Syntax

Code Block

language	none

% set profiles signaling ipSignalingProfile <SIP profile name> egressIpAttributes transport type1...type4 
	none
	sctp
	tcp
	tlsOverTcp
	udp

Command Parameters

Caption

0	Table
1	Transport Parameters

Parameter

Length/Range

Description

transport

N/A

Use this object to set up to four transport parameter types:

type1
type2
type3
type4

Each transport type above can be set to any one of the following transport protocols:

none (default)
sctp
tcp
tlsOverTcp
udp

...

Pagebreak

...

Space shortcuts

Page tree

Page History

Versions Compared

Old Version 7

New Version Current

Key

BCI

Command Syntax

Command Parameters

Domain Name

Command Syntax

Command Parameters

Flags

Command Syntax

Command Parameters

ISUB

Command Syntax

Command Parameters

Media QOS KPI Profile

Command Syntax

Command Parameter

Number Globalization Profile

Command Syntax

Command Parameters

Number Portability Attributes

Command Syntax

Command Parameters

P-Charge Info

Command Syntax

Command Parameters

Phone Context Parameter Length

Command Syntax

Command Parameter

AnchorPrivacyPrivacyPrivacy

Command Syntax

Command Parameters

Redirect

Command Syntax

Command Parameters

Signaling QOS KPI Profile

Command Syntax

Command Parameter

SIP Cause Mapping

Command Parameters

SIP Headers and Parameters

Command Syntax

Command Parameters

Transport

Command Syntax

Command Parameters

Anchor
Privacy
Privacy
Privacy