Page History

Reinstalling the

OS

Installing OS

1. Launch the host remote console through the BMC. Refer to Launching the Remote Console from the BMC.

2. Select Media in the JViewer and click Virtual Media Wizard.

   Caption
   0 Figure 1 Virtual Media Wizard

   
   

3. The Virtual Media screen appears. Select ISO Image from the CD/DVD Media1 section of the screen.

   Caption
   0 Figure 1 Virtual Media Screen

   
   

4. Click Browse. From the Open dialog, browse to and select the connexip-os_<version>_amd64.iso file and click Open.

   Caption
   0 Figure 1 Open Dialog Screen
   Image Modified

   
   

5. Click Connect CD/DVD. A message Device redirected in Read Only Mode appears on the screen. Click OK to continue. This mounts the ISO image from your local desktop or laptop.

   Caption
   0 Figure 1 Mounting Virtual CD/DVD
   Image Modified

   
   

6. Click Close.

7. Reboot the system from JViewer by executing the following command:
   # reboot

8. to exit the window.
9. Minimize the JViewer window.

10. On the SBC BMC GUI, navigate to Remote Control > Server Power Control. The Power Control and Status window is displayed.
    Observe that the "Host is currently on" message is in the window.

    Caption
    0 Figure 1 Server Power Control Window
    Image Added

    
    

11. Select the Power Off Server-Orderly Shutdown option and click Perform Action. This action brings the SBC host down.

    Caption
    0 Figure 1 Server Power Control - Off Option
    Image Added

    
    

12. Once the SBC host is down, from the same location, select Power On Server and click Perform Action. This action powers on and reboots the SBC host. 

    Caption
    0 Figure 1 Server Power Control - On
    Image Added

    
    Once the BMC is up and running, access the JViewer window.

    
    

13. Press <DEL> or <F2> immediately, when the splash screen appears After few minutes, the splash screen appears. Press <Del> or <Esc> key immediately to enter into BIOS configuration screen.

    Caption
    0 Figure 1 BIOS Splash Screen

    The BIOS setup utility screen displaysis displayed.

14. Use the right arrow key to navigate to the Save & Exit menu.

    Caption
    0 Figure 1 BIOS Setup Utility

    
    

15. Select AMI Virtual CDROM0 1.00 from the Save & Exit menu to boot from the virtual CD drive. This instructs the server to boot from the redirected ConnexIP OS ISO image.

    Caption
    0 Figure 1 Booting from Virtual CD Drive
    Image Modified

    
    

16. Select Install and press <Enter> to start the installation.

    Caption
    0 Figure 1 Sonus ConnexIP Installer Boot Menu
    Image Removed

    Select American English and press <Enter>.

    Caption
    0 Figure 1 Keymap Menu
    Image Modified

    
    

17. The automated installation process starts. This process takes approximately 30 to 40 minutes.

    Caption
    0 Figure 1 Partitions Formatting Screen

    
    

    Caption
    0 Figure 1 Installing the Base System

    
    

    Caption
    0 Figure 1 Selecting and Installing Software

    
    

    Caption
    0 Figure 1 Copying SBC Package

    
    

    Caption
    0 Figure 1 Running Post Install

    
    Once the installation is complete, the disk partition upgrade starts. At this stage, DO NOT power off the system.

    Caption
    0 Figure 1 Disk Partitioning

    
    Once the system reboots, the ConnexIP login screen appears on the screen.

    Caption
    0 Figure 1 ConnexIP Login Screen
    Image Modified

    This concludes the ConnexIP OS Installationinstallation/Rere-installation process.

18. Close the JViewer window.

Continue to install the desired SBC Application application build. Refer to Installing SBC Application to know more.