Versions Compared

Old Version 7

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Panel

In this section:

Table of Contents
maxLevel2

 

You can Use the Radius Server window to configure up to three RADIUS servers, per SBC, to which you want to submit requests to authenticate SBC users. When more than one RADIUS server is configured and RADIUS authentication is attempted, the server configured with the lowest numeric priority value is tried first. If fallback is configured, the server with the next lowest numeric priority value is tried next. SBC allows a configurable number of retries and time-outs before retry.

Include Page
Radius_auth_users
Radius_auth_users

To View the List

of Radius Servers

of RADIUS Servers

On the SBC main screen, go to Administration > Users and Application Management > Radius Authentication> Radius Server. The Radius Server window is displayed.

Caption
0Figure
1Radius Server Window
 

To Create a

Radius Server

RADIUS Server

Info
iconfalse
titleNote

You can configure up to three RADIUS servers per SBC. The New Radius Server option is not available once three servers are configured.

To create a new RADIUS server configuration:

  1.  Click New Radius Server. The Create New Radius Server window is displayed.

    Caption
    0Figure
    1Create New Radius Server Window
     
  2. Use the following table to specify configuration for a RADIUS server, then click Save.
Caption
0Table
1RADIUS Server Paramters
 
ParameterDescription
Server NameThe name for the RADIUS server (up to 23 characters).
Priority When configuring multiple RADIUS servers, use this attribute to specify the order to attempt RADIUS authentication. The RADIUS server with the lowest numeric priority value is contacted first.
StateOperational state of the RADIUS server. Options are
  • Disabled (default)
  • Enabled
Radius Server IP

The IPv4 address of the RADIUS server. The default value is 0.0.0.0.

Info
iconfalse
titleNote

IPv6 configuration for RADIUS servers is not supported at this time.

Radius Server PortThe RADIUS server port to which the SBC sends requests. Range: 1-65535. The default value is 1812.
Radius Nas IPThe IPv4 address of the SBC to send in the ACCESS_REQUEST message. The default value is 0.0.0.0.
Radius Shared SecretThe shared secret used to encrypt the data exchanged between the SBC and the RADIUS server. Range: 6-128 characters.
Mgmt Interface Group

The Management Interface Group to use to connect to the RADIUS server.

Info
iconfalse
titleNote

In an SBC HA configuration, four management IP addresses must be listed:

  • mgt0 and mgt1 IP addresses of the Active CE
  • mgt0 and mgt1 IP addresses of and Standby CE
Authentication MethodThe type of authentication to use.
  • Pap – Password Authentication Protocol. The password is sent in the RADIUS request, encoded with the shared secret. (default)
  • PeapmschapV2 – Protected EAP/ Microsoft Challenge Handshake Authentication Protocol. The password is sent using the Extensible Authentication Protocol over TLS and authenticated using the Microsoft Challenge Handshake Authentication Protocol.

To Copy a

Radius Server

RADIUS Server

Info
iconfalse
titleNote

You can configure up to three RADIUS servers per SBC. The Copy Radius Server option is not available once three servers are configured.

To copy the configuration of an existing RADIUS server and modify it to create a new configuration: 

  1. Click the radio button adjacent to its name.
  2. Click Copy Radius Server. The Copy Radius Server window opens showing the values of the configuration you are copying. 
  3. Make changes to the fields as needed and click Save.

To Delete a

Radius Server

RADIUS Server

To delete a RADIUS server configuration:

  1. Click the radio button adjacent to the name of the RADIUS server configuration you want to delete.
  2. Click the Delete icon (X) at the right end of the row.
  3. Confirm the deletion when prompted.

Pagebreak