Page History
| Panel | ||||||
|---|---|---|---|---|---|---|
| ||||||
Additional section:
|
| Add_workflow_for_techpubs | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|
|
| Panel | ||||
|---|---|---|---|---|
In this section:
|
| Info | ||
|---|---|---|
| ||
Related articles:
|
| Include Page | ||||
|---|---|---|---|---|
|
Use the Zone window to create and work with zones. A zone is used to group a set of objects
...
in a particular customer environment.
...
A zone can also be referenced by a SIP or H.323 trunk
...
group.
| Include Page | ||||
|---|---|---|---|---|
|
To View the Zone List
On the SBC main screen, go to Configuration > System Provisioning > Category: Base Provisioning > Zone
...
or
Configuration > System Provisioning > Category: SIP Carrier Peering > Zone or
All > Address Context > Zone
The Zone window opens. By default all zones are listed. Select an Address Context to list only the zones in that address context
| Caption | ||||
|---|---|---|---|---|
| ||||
The Zone can be checked for each Address Context or for all the Address Contexts created. Use the drop-down box to select the desired Address Context.
| Caption | ||||
|---|---|---|---|---|
| ||||
To Edit Zone
...
.
| Caption | |||
|---|---|---|---|
|
...
The Edit Selected Zone window is displayed below.
| Caption | ||||
|---|---|---|---|---|
| ||||
...
| |
To Create a Zone
To create a new
...
zone:
Click New Zone
...
.
...
| Caption | ||||
|---|---|---|---|---|
| ||||
The Create New Zone window
...
opens.
Caption 0 Figure 1 Create New Zone
...
Window
...
...
- Use the following table to configure the zone and then click Save.
| Caption | ||||
|---|---|---|---|---|
| ||||
|
|
|---|---|
Name | Specifies the name of the zone. Must be 1 |
...
to 23 characters. The |
...
name must be unique across all address contexts. |
ID |
...
specifies a unique numeric ID for this zone. The value ranges from 1 to 4096. |
...
The ID must be unique across all address contexts. | |
| Disable Zone Level Loop Detection |
|
...
|
...
|
...
|
DNS Group |
...
Select the name of the default DNS server group |
...
for the zone. |
| Remote Device Type |
...
Select the type of device facing this Zone. The options are:
|
...
|
...
|
...
| |
| Domain Name | Specifies the name of the fully qualified domain name for this Zone. The |
...
| name must be 1 to 63 characters. | |
| SIP Register Relay | Enable this option flag to relay REGISTER messages using the routes from a PSX. Options are:
|
| Dialog Transparency |
...
Specifies if dialog transparency is enabled for SIP messages processed in |
...
the zone. If enabled, SBC sends "Call-ID", "From" tag, and "To" tag transparently in the outgoing message.
|
...
|
...
|
...
|
...
|
...
|
...
| |||
| Retarget Support | Use this option to either disable load balancing or use the system-level load balancing settings for this zone.
| ||
| Advance Peer Control | Use this option to control whether the Mode, Action and Block Direction configuration is active in IP peers within the zone. Refer to System Provisioning - IP Peer for information on these options. Options are:
| ||
| Flexible Policy Adapter Profile | Use this Zone/Trunk Group parameter to associate a |
...
SIP Adapter Profile configured for flexible policy (Profile Type=Flexible |
...
Policy) with a particular Zone/Trunk Group. If a Flexible Policy Adapter Profile is provisioned both at the trunk group and zone levels, the trunk group’s profile takes precedence. If an Input Adapter Profile is configured, it is applied first to manipulate the PDU and then the Flexible Policy Adapter Profile rules are applied on the manipulated PDU.
|
...
|
...
| |||
| SIP Header For Anonymous Call |
To Delete Zone
To delete any of the created Zone, click the radio button next to the specific Zone which you want to delete.
| Caption | ||||
|---|---|---|---|---|
| ||||
...
Set this parameter to Remote Party ID to allow the SBC to pick the SIP header for calls from surrogate registered endpoints when the username in the From header is received as anonymous.
|
To Edit a Zone
To edit a zone:
- Click the radio button adjacent to the zone you want to edit. The Edit Selected Zone window opens.
- Make the required changes and click Save.
To Delete a Zone
To delete a zone:
- Click the radio button adjacent to the zone you want to delete.
- Click the delete icon (X) at the end of the
...
- row.
- Confirm the deletion when prompted.
Zone Commands
The zone commands are available from both system-level and configure modes. These command allows you to perform system-level commands against a particular zone, such as recovering blacklisted endpoints and resetting statistics counts on all signaling ports.
When a zone is selected from the Zone List window, the Zone Commands window appears at the bottom of the Zone window.
Select a command from the Commands drop-down list:
| Caption | ||||
|---|---|---|---|---|
| ||||
| Caption | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| ||||||||||||
|
| Pagebreak |
|---|
| Caption | ||||
|---|---|---|---|---|
| ||||
Click OK to remove the specific Zone from the list.
...
Overview
Content Tools