Parameter Name | Required | Service Affecting | Data Type | Default Value | Possible Values | Description |
---|
customAdminState | Yes | Yes | Enum | 1 | Possible values: - 0 - cmCustomDisabled
- 1 - cmCustomEnabled
- 2 - cmCustomDrain
| Enable or Disable this signaling group or set to Drain mode. |
---|
ApplyToPortName | Yes | Yes | string | none | 128 - Max Length | Specifies which physical T1/E1 Port this signaling group is for. |
---|
Description | No | No | string | none | 64 - Max Length | Describes the Signaling Group so that it is easily identifiable when selected for a Call Route Table |
---|
IsdnSgSwitchVariant | Yes | Yes | Enum | 3 | Possible values: - 0 - isvATT4ESS
- 1 - isvATT5ESS
- 2 - isvDMS100
- 3 - isvNI2
- 4 - isvETSI
- 5 - isvQSIG
- 6 - isvINET1500
| Specifies the ISDN variant for this signaling group |
---|
IsdnSgSideOrientation | Yes | Yes | Enum | 0 | Possible values: - 0 - isoUser
- 1 - isoNetwork
- 2 - isoNone
| Specifies the ISDN user/network side for this signaling group |
---|
IsdnSgOverlapRxMode | Yes | Yes | Enum | 0 | Possible values: - 0 - iorDisable
- 1 - iorEnable
| Specifies if overlap receiving is enabled on the signaling group. Only valid for Euro ISDN (ETSI) and QSIG Switch Variants. |
---|
IsdnSgOverlapTxMode | Yes | Yes | Enum | 0 | Possible values: - 0 - iosDisable
- 1 - iosEnable
| Specifies if overlap sending is enabled on the signaling group. Only valid for Euro ISDN (ETSI) and QSIG Switch Variants. |
---|
IsdnSgIndicatedChannel | Yes | Yes | Enum | 1 | Possible values: - 0 - iicPreferred
- 1 - iicExclusive
| Specifies the setting of the Indicated Channel field for the Channel Identification IE in the SETUP message sent to the far end for this signaling group. |
---|
IsdnServiceMessageCapability | Yes | Yes | Enum | 1 | Possible values: - 0 - iscDisable
- 1 - iscEnable
| Specifies if service messaging is used on the signaling group. Only valid for ATT 4ESS, ATT 5ESS, NI2 and INS NET 1500 Switch Variants. |
---|
IsdnStopFarEndT310UponTryingFromSip | Yes | Yes | Enum | 0 | Possible values: - 0 - isfDisable
- 1 - isfEnable
| Specifies if a Q.931 PROGRESS message is sent to the far-end so that it does not timeout (T310) while SIP response is pending from the SIP leg, causing the call to release. This setting typically enabled only for testing scenarios and should not used in a production system. |
---|
IsdnAllowCallingNameDisplayToSwitch | Yes | Yes | Enum | 0 | Possible values: - 0 - iacDisable
- 1 - iacEnable
| Specifies if the Q.931 SETUP message is sent to the far-end should include the DISPLAY Information Element (IE). If this option is enabled, the DISPLAY IE is populated for NI2 or Euro-ISDN switch types, otherwise the DISPLAY IE is not populated for these switch types. Info |
---|
This setting is available when ISDN Side is set to User and Switch Variant is either NI2 or Euro-ISDN. |
Info |
---|
In general, the DISPLAY IE is populated according to ISDN communication standards. The NI2 and Euro-ISDN specifications state that the DISPLAY IE _should not_ be populated. This option allows you to override that configuration for your environment. |
|
---|
IsdnSgHuntMethod | Yes | Yes | Enum | 4 | Possible values: - 0 - sghmStandard
- 1 - sghmReverseStandard
- 2 - sghmRoundRobin
- 3 - sghmLeastIdle
- 4 - sghmMostIdle
- 5 - sghmOwnNumber
| Method that Call Control uses to allocate ISDN channels. This is only valid for Outbound or Bidirectional Direction settings. - Standard - This option assigns the first available low numbered channel.
- Reverse Standard - This option assigns the last available high numbered channel.
- Round Robin - This option assigns channels based on next available from low numbered to high numbered.
- Least Idle - This option chooses channels based on the least idle channel.
- Most Idle - This option chooses channels based on the most idle channel.
|
---|
IsdnSgDirection | Yes | Yes | Enum | 2 | Possible values: - 0 - sgdirInbound
- 1 - sgdirOutbound
- 2 - sgdirBidirectional
| Indicates the direction of calls supported - Inbound - Support only incoming calls from ISDN endpoints.
- Outbound - Support only outgoing call to ISDN endpoints.
- Bidirectional - Support both incoming or outgoing calls to ISDN endpoints.
|
---|
IsdnSgRingbackPlayPolicy | Yes | Yes | Enum | 0 | Possible values: - 0 - sgrbpAuto
- 1 - sgrbpAlways
- 2 - sgrbpNever
- 3 - sgrbpAutoOnAlertProgress
- 4 - sgrbpAlwaysOnAlertProgress
| Specifies when to generate local ring back - Auto on Alert - Depends if inband audio is available when processing Alert
- Always on Alert - always generate inband ringback when processing Alert
- Auto on Alert/Progress - Depends if inband audio is available when processing Alert or Progress
- Always on Alert/Progress - always generate inband ringback when processing Alert or Progress
- Never - never generate inband ringback
|
---|
ToneTableNumber | Yes | Yes | int | 0 | Possible values: - 0 - Minimum
- 65534 - Maximum
| Specifies the Tone Table to use on this signaling group. This option is only available for Inbound and Bidirectional. |
---|
ActionsetTableNumber | No | No | int | 0 | Possible values: - 0 - Minimum
- 65534 - Maximum
| Specifies the Action Set Table to use on this signaling group. This option is only available for Inbound and Bidirectional. |
---|
RouteTableNumber | Yes | Yes | int | 1 | Possible values: - 1 - Minimum
- 65534 - Maximum
| Specifies the Call Route Table to use on the signaling group to route calls with. This option is only available for Inbound and Bidirectional. |
---|
NoChannelAvailableId | No | No | int | 34 | Possible values: | In case of "No Channel/Circuit available" release cause code, CCC is going to map this to the value configured against this entry in the signaling group. This cause code will be sent to the relevant protocol module. |
---|
TimerSanitySetup | No | No | int | 255000 | Possible values: - 180000 - Minimum
- 750000 - Maximum
| Specifies the sanity timer for setup message, in milliseconds. A Call that has not received a response from the peer switch will be released after this time. This is for all call types. The duration of this timer should be equal to or greater than the T301 timer. |
---|
IsdnSgTimerT301 | Yes | Yes | int | 180 | Possible values: |
---|