Parameter | Description |
|---|
Name
| Specifies the name of the Gateway Trunk Group. |
State
| The administrative state of the gateway trunk group: |
Mode
| The operational mode of the gateway trunk group: Out of Service In Service
|
Action
| The action when putting this gateway trunk group out Of Service. This object controls whether calls are forced off or allowed to dry up upon a mode out-of-service. Select any one of the option: Dryup (default)Force Undefined
|
Dryup Timeout
| Dry up timeout (in minutes) when this gateway trunk group is out Of Service with dry up action. Enter a value in the range of 0-1440. Default is 5 minutes. |
Acc MC1Percent
| The percentage of calls to continue to send to a remote congested gateway (in MC1). Enter value in range of 0-100 percent. Default is 90 percent. |
ACC MC2Percent
| The percentage of calls to continue to send to a remote congested gateway (in MC2). Enter value in range of 0-100 percent. Default is 70 percent. |
ACC Timer
| Specifies the automatic congestion control timer. Enter value in range of 0-10. Default is 0. |
Parent Shared CAC Limits Pool Name | Name of an existing Shared CAC Limits Pool that you assign as the parent of the Gateway Trunk Group.
|
Packet Outage |
Minimum Duration
| This is the outage (in milliseconds) on a call for that call to be counted as part of the packet outage detection algorithm. Enter value in range of 0-65535 in milliseconds. Default is 6000 milliseconds. |
Calls
| The number of calls with outages required within the current interval to declare a packet outage event. Enter value in range of 0-65535. Default is 1000. |
Bandwidth Limit Reduction
| The amount to reduce the bandwidth limit (as a percentage of the configured limit) when a packet outage is detected. Enter value in range of 0-100 percent. Default is
50 percent. |
Detection State
| Used to enable automatic bandwidth reduction when a packet outage is detected. Select any one of the option: Disabled (default)
Enabled
|
Detection Interval
| The size of the packet outage detection interval in minutes. Enter value in range of 5- 1440 minutes. Default is 15 minutes. |
| Call Reservation |
Inbound
| The percent of channels reserved for inbound calls in IP gateway trunk groups. Must be 0-100, in increments of 5. Default is 0. |
State
| The administrative state of the packet outage: Disabled (default) Enabled
|
Priority Call
| The number of priority call resources (circuits or IP calls) to be reserved for this trunk group. Must be 0-100, default is 1. |
Incoming Call
| The number of incoming call resources (circuits or IP calls) to be reserved for this trunk group. Must be 0-128, default is 1. |
Outgoing Call
| The percentage of outgoing call resources (circuits or IP calls) to be reserved for this trunk group. This percentage is applied to the total number of circuits less the circuits reserved for incoming calls less the circuits reserved for priority calls. Must be 0-100, default is 10%. |
| SILC |
State
| The Administrative state of the SILC traffic control. Select any one of the option: Disabled (default)Enabled
|
MC1Percent
| The percentage of calls to accept when the machine congestion level is 1. Enter value in range of 0-100 percent. Default is 75. |
MC2Percent
| The percentage of calls to accept when the machine congestion level is 2. Enter value in range of 0-100 percent. Default is 25. |
| CAC | |
Call Limit | Total number of concurrent calls (0-2147483647, or unlimited), either ingress or egress, that are allowed (default=Unlimited). |
Bandwidth Limit | The total media bandwidth limit (0-2147483647, or unlimited), in Kbits/sec (default=Unlimited). |
Emergency Oversubscription | The percentage (0-1000) of resource oversubscription allowed for emergency calls (default=10). |
Hpc Oversubscription | This parameter specifies the amount of resource over-subscription as a percentage (0-100), that is allowed for HPC. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC are allowed up to the configured percentage value (default=10). |
| Egress | |
Call Limit | Total number of concurrent calls (0-2147483647, or unlimited), either ingress or egress, that are allowed on egress (default=Unlimited). |
Emergency Oversubscription | The percentage (0-1000) of resource oversubscription allowed for emergency calls (default=10). |
Hpc Oversubscription | This parameter specifies the amount of resource over-subscription as a percentage (0-100), that is allowed for HPC. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC are allowed up to the configured percentage value (default=10). |
Call Rate Max | Maximum (SBC 5000: 1-450, or unlimited; SBC 7000: 1-1350, or unlimited) sustained egress call rate allowed in calls per second. Note: You can set both Call Burst Max and Call Rate Max as "unlimited"; however, if you assign a value to one parameter, the other must also be assigned a value. |
Call Burst Max | Maximum (SBC 5000: 1-900, or unlimited; SBC 7000: 1-2700, or unlimited) allowed burst size (above the allowed sustained rate) for ingress call attempts, in calls per second (default=unlimited). |
| Ingress | |
Call Limit | Total number of concurrent calls (0-2147483647, or unlimited), either ingress or egress, that are allowed on ingress (default=Unlimited). |
Emergency Oversubscription | The percentage (0-1000) of resource oversubscription allowed for emergency calls (default=10). |
Hpc Oversubscription | This parameter specifies the amount of resource over-subscription as a percentage (0-100), that is allowed for HPC. When the baseline call limit and bandwidth limit are reached, normal calls are not admitted, but additional HPC are allowed up to the configured percentage value (default=10). |
Call Rate Max | Maximum (SBC 5000: 1-450, or unlimited; SBC 7000: 1-1350, or unlimited) sustained ingress call rate allowed in calls per second. Note: You can set both Call Burst Max and Call Rate Max as "unlimited"; however, if you assign a value to one parameter, the other must also be assigned a value. |
Call Burst Max | Maximum (SBC 5000: 1-900, or unlimited; SBC 7000: 1-2700, or unlimited) allowed burst size (above the allowed sustained rate) for ingress call attempts, in calls per second (default=unlimited). |
| Media |
Media IP Interface Group Name
| Interface group to be used for media. |
Source Address Filtering
| If enabled, filter out incoming media packets which do not match the expected source IP address and UDP port. |
Direct Media Allowed
| Specifies whether to enable the direct-media path so that media flows directly between endpoints in the same direct-media group or not. The options are: Disabled (default) Enabled
|