...
| borderColor | green |
|---|
| bgColor | transparent |
|---|
| borderWidth | 2 |
|---|
Back to Table of Contents
Back to Installing SBC SWe on Virtual Platforms
| Add_workflow_for_techpubs |
|---|
| AUTH2 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909df, userName='null'} |
|---|
| AUTH1 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c85b00e8, userName='null'} |
|---|
| REV5 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ccbb08c9, userName='null'} |
|---|
| REV6 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5a09e7, userName='null'} |
|---|
| REV3 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cef30cd0, userName='null'} |
|---|
| REV1 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cc4107ae, userName='null'} |
|---|
| REV2 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cba10618, userName='null'} |
|---|
|
...
This section describes
hardware and software requirements and recommendations.To install and configure
, make sure the Virtual Machine (VM) host meets the following recommended hardware, server platform and software requirements...
.
| Warning |
|---|
|
The recommended hardware and software settings are intended to ensure optimum stability and performance. If the recommended settings are not used, system may not behave as expected. |
SBC SWe for KVM Hypervisor – Server Hardware Requirements
| Multiexcerpt |
|---|
| MultiExcerptName | SBC SWe for KVM Hypervisor – Server Hardware Requirements |
|---|
|
...
The following table lists the server hardware requirements |
...
. | Caption |
|---|
| 0 | Table |
|---|
| 1 | KVM Hypervisor Server Hardware Requirements |
|---|
| |
|
...
| Configuration | Requirement |
|---|
| Processor | Intel Xeon processors (Nehalem micro-architecture or above) |
|
...
with 6 cores and above (processors should support hyper threading). |
|
Westmere (or newer) processors are recommended for better SRTP performance. These processors have the AES-NI instruction set for performing cryptographic operations in hardware. |
| | RAM | Minimum 24 GB | | Hard Disk | Minimum 500 GB | | Network Interface Cards (NICs) | Minimum 4 NICs. |
|
...
| Info |
|---|
| Make sure NIC has multi-queue support which enhances network performance by allowing RX and TX queues to scale with the number of CPUs on multi-processor systems. |
| | Ports | Number of ports allowed: - 1 Management port
- 1 HA port
- 2 Media ports
|
|
...
...
...
on platforms using Intel processors. Platforms using AMD processors are not supported. |
...
...
Back To Top
BIOS Setting Recommendations
Sonus recommends the following BIOS settings for optimum performance:
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Recommended BIOS Settings for Optimum Performance |
|---|
|
| BIOS Parameter | Recommended
Setting | Details |
|---|
| Intel VT-x (Virtualization Technology) | Enabled | For hardware virtualization | | Intel Hyper-Threading | Enabled | | | Intel Turbo Boost | Enabled | | | CPU power management | Maximum Performance | |
|
For example, the BIOS settings are shown below for HP DL 380p Gen8 servers. For BIOS settings of other servers, refer to the respective vendor's website.
| Caption |
|---|
| 0 | Table |
|---|
| 1 | BIOS Setting Recommendations for HP DL380p Gen8 Server |
|---|
|
| BIOS Parameter | Recommended
Setting | Default Value |
|---|
| HP Power Profile | Maximum Performance | Balanced Power and Performance | | Thermal Configuration | Maximum Cooling | Optimal Cooling | | HW Prefetchers | Disabled | Enabled | | Adjacent Sector Prefetcher | Disabled | Enabled | | Processor Power and Utilization Monitoring | Disabled | Enabled | | Memory Pre-Failure Notification | Disabled | Enabled | | Memory Refresh Rate | 1x Refresh | 2x Refresh |
|
| MultiExcerptName | SBC SWe for KVM Hypervisor – Software Requirements |
|---|
|
SBC SWe for KVM Hypervisor – Software RequirementsFollowing are KVM hypervisor and SBC SWe software requirements: |
...
| Caption |
|---|
| | Software | Version | Tested or Qualified Version |
|---|
|
|
...
| KVM Module | 3.10.0 or above | 3.10.0 | | QEMU Emulator | 1.5.3 | 1.5.3 | | libvirtd (libvirt) | 1.1.1 | 1.1.1 | | virt-manager | 0.10.0 | 0.10.0 |
|
|
Downloading the SBC SWe
...
...
Processors and VM configuration (CPUs, RAMs, Virtual Hard Disk, NICs, and bridge Settings) |
...
must be identical for SBC SWe HA pair. |
| Info |
|---|
|
BIOS settings and recommendations must not be changed once it is applied on the server. |
...
KVM Configuration Recommendations
| Caption |
|---|
| 0 | Table |
|---|
| 1 | KVM Configuration Recommendations |
|---|
|
| vCPU | Minimum 4 vCPUs required. But in case where there are only four physical cores available, you must configure the VM with only 3 vCPUs. Any number of vCPUs may be configured depending upon the call capacity requirements. KVM Direct-IO mode is only supported for PKT ports for vCPUs >=4. | | vRAM | Reserve the memory based on call capacity and configuration requirements. Refer to for supported call capacities with different configuration limits. | | Virtual Hard Disk | Set Hard Disk (virtual) size as 100 GB or more (based on requirements of retaining CDRs, logs, etc. for number of days). Note: Hard disk size cannot be changed after the SBC SWe software is installed. | | vNICs | Set number of virtual NICs as 4 (1-MGMT, 1-HA, 1-PKT0 and 1-PKT1). - Use only Virt-IO driver.
- Associate each vNIC to separate bridges.
|
|
| Info |
|---|
|
- Processors, KVM hypervisor version and VM configuration (vCPUs, vRAMs, Virtual Hard Disk, vNICs, and vSwitch Settings) must be identical for SBC SWe HA pair.
|
...
- settings and recommendations must not be changed once it is applied on the server.
|
...