Versions Compared

Old Version 5

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

This section helps you to understand IngressUse this window to configure ingress-specific call admission control (CAC) configuration for the a specified SIP trunk group.

To View and Edit Cac - Ingress

On the 

Spacevars
0product
 main On SBC main screen, go to to Configuration >  > System Provisioning > Category > Category: Trunk Provisioning Provisioning > Trunk  Trunk Group > Sip  > SIP Trunk Group > Cac >  > CAC > Ingress. The Ingress window is displayed.

The Cac - Ingress can be checked for each Address Context, for each Zone, for each Sip Trunk Group created or for all the Address Contexts, Zones and Sip Trunk Groups created. Use the drop-down box boxes to select the desired Address Context, Zone and Sip SIP Trunk Group.

Caption
0Figure
1Sip Trunk Group - Cac Ingress Main Fields
 

Image Removed 

The  The Edit Ingress window is displayed.

Caption
0Figure
1H323Trunk SIP Trunk Group - Cac CAC Ingress Edit Window
Image Added 

 

...

Include Page
_Subscribe_CAC_Access_Restriction
_Subscribe_CAC_Access_Restriction

Use the following table to configure the options and then click Save.

Image Removed

The following fields are displayed:

 
Caption
0Table
1CAC - Ingress Parameters


Parameter

Description

Call Rate Max

Specifies the maximum sustained ingress call rate allowed in calls per second. (range: 1-450, or unlimited.

Spacevars
0series2
range is 1-1350, or unlimited).

Note

You can set both “callBurstMax” and “CallRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value.


Call Burst Max

Specifies the maximum allowed burst size (above the allowed sustained rate) for ingress call attempts, in calls per second. (range: 1-900, or unlimited.
Spacevars
0series2
range is 1-2700, or unlimited).

Register Rate Max

Specifies the maximum sustained ingress rate (registrations per second) of initial SIP registrations allowed. (range: 1-1000, or unlimited.

Spacevars
0series2
range is 1-3000, or unlimited)

Note

You can set both “registerBurstMax” and “registerRateMax” as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value.


Register Burst Max

Specifies the maximum allowed burst (above the allowed sustained rate) for ingress initial SIP registrations. (range: 1-1000, or unlimited.

Spacevars
0series2
range is 1-3000, or unlimited)

Call Limit

Specifies the total number of concurrent calls (either ingress or egress) allowed on ingress. The value ranges from 0 to 2147483647 or unlimited (default).

Emergency Oversubscription

Specifies the oversubscription of resources (as a percentage) that is allowed for emergency calls. The value ranges from 0 to 1000 and the default value is 10.

Entended Emergency

Ip

IP Limit

Specifies the maximum sustained ingress rate (registrations per second) of initial SIP registrations allowed. The value ranges from 0 to 40000 and the default value is 0.

Subscribe Rate Max

Specifies the maximum sustained ingress rate (subscribes per second) of initial SIP subscribe request. (range: 1-1000, or unlimited.
Spacevars
0series2
range is 1-3000, or unlimited)
Subscribe Burst MaxSpecifies the maximum allowed burst (above the allowed sustained rate) for ingress initial SIP subscribe request. (range: 1-1000, or unlimited.
Spacevars
0series2
range is 1-3000, or unlimited)

Other Req Rate Max

Specifies the maximum sustained ingress rate (requests per second) of other out-of-dialog SIP requests. (range: 1-1000, or unlimited.

Spacevars
0series2
range is 1-3000, or unlimited).

Other Req Burst Max

Specifies the maximum allowed burst (above the allowed sustained rate) for any other ingress out-of-dialog SIP request. (range: 1-1000, or unlimited.

Spacevars
0series2
range is 1-3000, or unlimited).

Hpc OversubscriptionSpecifies the over-subscription of the resources (in a percentage) that is allowed for HPC calls. When the baseline call limit and bandwidth limits are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured value percentage. The value ranges from 0 to 100 % and the default value is 10 %.

Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

 

Pagebreak