Page History

...

The BMC web application allows provisioning primary and secondary of the four host management interfaces. When the host management interfaces are configured, a direct link from BMC is enabled to the EMA/EMA Platform Mode for installing and upgrading the 

Use the following procedure to configure the primary and secondary 4 host management interfaces:

1. Log on to SBC BMC GUI using the IP address configured in one of the previous sectionsections.

   Code Blocktip
   languagetitle none Tip
   Use any one of the following methods to obtain the BMC IP address: - Configuring SBC 5400 BMC IP Address Via Serial Console Or - Configuring SBC 5400 BMC for Remote Access username: root password: superuser

   
   The BMC Main Screen appears:

   Caption
   0 Figure 1 BMC Main Screen
   Image Modified

    

2. Click Navigate to Configuration > Platform Management Network tab. The Platform Management Network Settings screen is displayed.

   warning

   Tip
   title Tip
   Refer
   Note
   Refer to SBC 5400 Media Ports and Operation Operational Modes to know more about these four media ports and their operational modes.
   Any changes to the media port speed, deletes the existing configuration. To use the option, Enable 10G Media Speed, power off the host first.

   The SBC 5400 platform includes the following configurable media port configurations.

   Pkt0 and Pkt1 run at 1 Gbps

   Caption
   0 Table 1 Media Port Configuration Options

   Media Port SpeedDescription10 Gbps
   • Pkt0 runs at 10 Gbps
   • Pkt1, Pkt2, and Pkt3 are inactive
   1 Gbps

   In 4x1Gbps mode:

   • Pkt0, Pkt1, Pkt2, and Pkt3 run at 1 Gbps and all the four ports are configurable.
   • Pkt2 and Pkt3 ports will not operate without the 4x1Gbps license.

   In 2x1 Gbps mode:

3. Pkt2 and Pkt3 are inactive

Note
In 10 Gbps mode, only media0 is configurable and operable.

Note
2 x 1 Gbps mode is a default mode that any SBC 5400 platform can use. A license is required to use both 4 x 1 Gbps and 1 x 10 Gbps modes. If there is no license, only ports 0 and 1 are operable.

The media port speed is user-configurable and the following licenses are added in this release in support of the media port configurations:
• SBC-4X1GMP – This license allows four 1 Gbps media ports.
• SBC-1X10GMP – This license allows one 10 Gbps media port.

 

Caption
0 Figure 1 BMC Platform Management Network Settings Window
Image Added

Image Removed

Tip

 note

title

Tip

A message appears to enter the management IP addresses for the first time installation.

4. If the management interfaces have not yet been configured, a warning message appears. Click OK to proceed with the Management Port configuration.

   Caption
   0 Figure 1 BMC PMNS Info Message

   Image Removed

5. Click OK.

6. Management Interfaces Not Configured Warning message

   Image Added

7. Configure the following network settings for all the four management interfaces from 0 to 3.as needed:
   

   - IPv4 Address or/and , Prefix and Default Gateway

   - IPv6 Address

   - Prefix

   - Default Gateway

   , Prefix and Default Gateway

   Tip
   title Tip
   The IPv4 Address, Prefix and Default Gateway should be configured for Management Interface "0". For all other Management Interfaces, the settings are optional.

   Caption
   0 Figure 1 BMC Platform Management Network Settings Window
   Image Modified

    

8. Click Save.

...

1. Tip
   title Tip
   Once you save the changes to the Management IP addresses, a warning message appears. Note that the changes to the Management IP addresses will only take effect when the SBC application is Installed (or re-Installed if already present). Refer to SBC 5400 - Installing Application for more information.

   Caption
   0 Figure 1 BMC Warning Message

...

1. Image Added

2.  Click OK to complete the process.

...