Page History

Warning
Sonus-provided SFP modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.

Tooltip
tip Use ESD protective device

1 Gb SFP

Parts

Characteristics

The 

Spacevars
0 model5

supports the following Small Form-factor Pluggable (SFP) transceivers in all Management, Media , and HA ports. SFPs are Customer Replaceable Units (CRUs).

Product Code

Div
class pdf6pttext
Caption 0 Table 1 1Gb SFP Parts 3 1Gb SFP Parts Transceiver Type

Order Code

Product Code SFP Type Manufacturers  Part Number Wavelength  (nm) Tx Power (dBM) Rx Power (dBM)

Description

Single

Multi-mode fiber

SBC-SFPSM-1G

SBC‐5XXXSFPMM   1G Ethernet MM AVAGO TECHNOLOGIES AFBR‐5715PZSN1 BROADCOM AFBR‐5715PZ‐SN1 FINISAR FTLF8519P2BNL‐SS FINISAR  FTLF8519P3BNL‐SS 850 -9.5 (Min) -3 (Max) -17 (Min) 0 (Max)

SBC-5400-SFPSM

GIG-E,

SINGLE MODE

MULTIMODE, FIBER OPTIC

TRANSCEIVER

TRANCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP),

10KM 1310NM, DMI

300M Single

Multi

-mode fiber

SBC-SFPMM-1G

SBC‐5XXXSFPSM   1G Ethernet  SM AVAGO TECHNOLOGIES AFCT‐5715PZSN1 BROADCOM AFCT‐5715PZSN1 FINISAR FTLF1318P2BTL‐SS FINISAR FTLF1318P3BTL‐SS 1310 -9.5 (Min) -3 (Max) -19 (Min) -3 (Max)

SBC-5400-SFPMM

GIG-E,

MULTIMODE

SINGLE MODE, FIBER OPTIC

TRANCEIVER

TRANSCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 10KM 1310NM,

300M

DMI Copper  SBC-5XXX-SFPCOPPER

-1G

1G Ethernet Copper AVAGO TECHNOLOGIES ABCU-5740RZ-SN1 BROADCOM ABCU-5740RZ-SN1 FINISAR FCLF8521P2BTL-SS NA NA NA NA NA

SBC-5400-SFPCOPPER

GIGE, 1000 BASE-T SMALL FROM PLUGGABLE (SFP)

Info
title Note
These numbers are taken from Vendor Datasheets as well as IEEE 802.3ae for the 1G parts.

 

10 Gb SFP

Parts

Characteristics

Optionally, Pkt0 can be used as a single 10 Gb port, with the remaining MEDIA ports empty. The parts for the 10 Gb SFPs are:

Div
class pdf6pttext
Caption 0 Table 1 10Gb SFP Parts 3 10Gb SFP Parts Transceiver Type

Order CodeProduct Code

Product Code SFP Type Manufacturers  Part Number Wavelength  (nm) Tx Power (dBM) Rx Power (dBM) Description

Single

Multi-mode fiber

SBC-SFPSM-10GSBC-5400-SFPSM

SBC‐SFPMM‐10G 10G Ethernet MM AVAGO TECHNOLOGIES AFBR‐709SMZSN1 BROADCOM AFBR‐709SMZ‐SN1 FINISAR FTLX8571D3BCL‐SS FINISARFTLX8574D3BCL‐SS 850 -7.9 (Min) -1 (Max) -11.1 (Min) 0.5 (Max) 10.3 GB/S, MULTIMODE

10.3GB/S, SINGLE MODE

, FIBER OPTIC XCVR, LC, SFP

, 10KM 1310NM, DM

, 300M 850NM, DMI GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE Single

Multi

-mode fiber

SBC-SFPMM-10GSBC-5400-SFPMM10.3GB/S, MULTI-

SBC‐SFPSM‐10G   10G Ethernet  SM AVAGO TECHNOLOGIES AFCT‐709SMZSN1 AVAGO TECHNOLOGIES AFCT739SMZ‐SN1 BROADCOM AFCT‐709SMZSN1 BROADCOM AFCT‐739SMZ‐SN1 FINISAR FTLX1471D3BCL‐SS 1310 -8.2 (Min) 0.5 (Max) -12.6 (Min) 0.5 (Max) 10.3 GB/S, SINGLE MODE, FIBER OPTIC XCVR, LC, SFP,

300M 850NM, DMI

10KM 1310NM, DM

Info
title Note
These numbers are taken from Vendor Datasheets as well as IEEE 802.3ae for the 10G parts.

 

To replace SFPs, use the procedures from the section Replacing the SFP.

Caption
0 Figure 1 SFP Ports

Parts and Tools Required

• Electrostatic discharge (ESD) strap
• Replacement SFP transceivers.

note

Info
title Note
To prevent damage from electrostatic discharge, an ESD strap is provided in the accessory kit. Refer to Connecting ESD Wrist Strap to install it.

 

Anchor
ReplacingSFP ReplacingSFP

Replacing the SFP

Perform the following procedure to replace the SFP:

1. Attach an ESD wrist strap using the ESD grounding point on the rear panel of the chassis (refer to Connecting ESD Wrist Strap for details).

2. Disconnect the fiber optic and/or Cat 5 cables, as appropriate, from media ports (Pkt0/1/2/3) and HA ports (HA 0-1).

3. Disengage the SFP transceiver from

   Spacevars
   0 model5

   . The method used to disengage the SFP transceiver will vary according to the manufacturer. For example, hold the wire latch and move it downwards to the horizontal position and pull it outwards, as shown below.

    

   Caption
   0 Figure 1 Removing SFP

4. Insert the Sonus-approved SFP transceiver into the desired socket and ensure that the latch mechanism engages.

5. Reconnect the fiber optic and/or Cat 5 cables, as appropriate, to media and HA ports.
6. Verify LEDs above the part are flashing indicating link status and data activity.
7. Verify port functionality using the application.

CRU Storage

Tooltip
tip ESD protective device

All 

Spacevars
0 model5

CRUs are shipped in electrostatic discharge bags and should be handled using appropriate ESD precautions.

The storage environment for these CRUs are:

• Humidity must be less than 95% (non-condensing).
• Temperature must be between -40C and +70C.

 

Include Page
ESD_footnote ESD_footnote

Pagebreak