Versions Compared

Old Version 4

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Panel

In this section:

Table of Contents

 

Use these procedures to configure SBC and Lync servers to use the TCP protocol.

Note

This page provides sample configuration therefore the values provided will vary based on the user environment.

Note

The pathCheck Profile on Lync IP-Peer needs to be disabled while switching from TCP to TLS and vice versa.

Include Page
IP_IGs_ServedBySeperateProcessors
IP_IGs_ServedBySeperateProcessors

Include Page
TLS_version
TLS_version

Include Page
sip-tls-tcp
sip-tls-tcp

Global Configuration

This section provides global configuration steps.

  1. Create Codec Entry.

    1. Create G.711 Codec Entry or create G.711 with Silence Suppresion Codec Entry for Comfort Noise.

      Code Block
      languagenone
      set profiles media codecEntry G711_2833_20 dtmf relay rfc2833
set profiles media codecEntry G711_2833_20 packetSize 20

       
      OR

       

      Code Block
      languagenone
      set profiles media codecEntry G711SS_2833_20 sendSid enable dtmf relay rfc2833
set profiles media codecEntry G711SS_2833_20 packetSize 20

  2.  Set RTCP interval.

    Code Block
    languagenone
    set system media mediaRtcpControl senderReportInterval 5

  3. Create SIP Domains for Mediation Servers to be used with Call Transfer.

    Code Block
    set global sipDomain med1.domain.com
set global sipDomain med2.domain.com

  4. Configuring Tone And Announcement Profile. 

    Code Block
    set profiles media toneAndAnnouncementProfile LRBT_PROF
set profiles media toneAndAnnouncementProfile LRBT_PROF localRingBackTone signalingTonePackageState enable makeInbandToneAvailable enable
set profiles media toneAndAnnouncementProfile LRBT_PROF localRingBackTone flags useThisLrbtForIngress enable
set profiles media toneAndAnnouncementProfile LRBT_PROF localRingBackTone flags dynamicLRBT enable
set system mediaProfile compression 75 tone 25

Configuration in the Lync Side (Enterprise Network)

The following configuration is made on the Lync side:

  1. Create Path Check Profile.

    Code Block
    languagenone
    set profiles services pathCheckProfile LYNC_OPTIONS protocol sipOptions sendInterval 20 replyTimeoutCount 1 recoveryCount 1

  2. Create Packet Service Profile with G.711 or create Packet Service Profile with G.711 w/ Silence Suppresion.

    Code Block
    languagenone
    # Using G.711 Codec
set profiles media packetServiceProfile LYNC_PSP
set profiles media packetServiceProfile LYNC_PSP codec codecEntry1 G711_2833_20
set profiles media packetServiceProfile LYNC_PSP rtcpOptions rtcp enable terminationForPassthrough enable
set profiles media packetServiceProfile LYNC_PSP preferredRtpPayloadTypeForDtmfRelay 101
set profiles media packetServiceProfile LYNC_PSP silenceInsertionDescriptor g711SidRtpPayloadType 13 heartbeat enable
# Using G.711 Codec with Silence Suppresion for Comfort Noise
set profiles media packetServiceProfile LYNC_PSP
set profiles media packetServiceProfile LYNC_PSP codec codecEntry1 G711SS_2833_20 
set profiles media packetServiceProfile LYNC_PSP rtcpOptions rtcp enable terminationForPassthrough enable
set profiles media packetServiceProfile LYNC_PSP preferredRtpPayloadTypeForDtmfRelay 101
set profiles media packetServiceProfile LYNC_PSP silenceInsertionDescriptor g711SidRtpPayloadType 13 heartbeat enable
set profiles media packetServiceProfile LYNC_PSP packetToPacketControl transcode only
set profiles media packetServiceProfile LYNC_PSP packetToPacketControl codecsAllowedForTranscoding thisLeg g711u otherLeg g711u

  3. Create IP Signaling Profile.

    Code Block
    languagenone
    set profiles signaling ipSignalingProfile LYNC_IPSP
set profiles signaling ipSignalingProfile LYNC_IPSP commonIpAttributes flags includeReasonHeader enable
set profiles signaling ipSignalingProfile LYNC_IPSP commonIpAttributes flags sendPtimeInSdp enable
set profiles signaling ipSignalingProfile LYNC_IPSP commonIpAttributes flags sendRtcpPortInSdp enable
set profiles signaling ipSignalingProfile LYNC_IPSP commonIpAttributes flags routeUsingRecvdFqdn enable
set profiles signaling ipSignalingProfile LYNC_IPSP commonIpAttributes flags minimizeRelayingOfMediaChangesFromOtherCallLegAll enable
set profiles signaling ipSignalingProfile LYNC_IPSP commonIpAttributes flags relayDataPathModeChangeFromOtherCallLeg enable
set profiles signaling ipSignalingProfile LYNC_IPSP commonIpAttributes optionTagInRequireHeader suppressReplaceTag enable
set profiles signaling ipSignalingProfile LYNC_IPSP commonIpAttributes flags publishIPInHoldSDP enable
set profiles signaling ipSignalingProfile LYNC_IPSP egressIpAttributes numberGlobalizationProfile DEFAULT_IP
set profiles signaling ipSignalingProfile LYNC_IPSP egressIpAttributes domainName useZoneLevelDomainNameInContact enable
set profiles signaling ipSignalingProfile LYNC_IPSP egressIpAttributes transport type1 tcp
set profiles signaling ipSignalingProfile LYNC_IPSP ingressIpAttributes flags sendSdpIn200OkIf18xReliable enable

  4. Create Feature Control Profile.

    Code Block
    languagenone
    set profiles featureControlProfile LYNC_FCP ipProtocolFlags useIpProtocol enable defaultCalledUser enable

  5. Create IP Interface Group.

    Code Block
    languagenone
    set addressContext a1 ipInterfaceGroup LIF1 ipInterface PKT0_V4 ceName LYNCSBC portName pkt0
set addressContext a1 ipInterfaceGroup LIF1 ipInterface PKT0_V4 ipAddress 10.10.10.11 prefix 24
set addressContext a1 ipInterfaceGroup LIF1 ipInterface PKT0_V4 mode inService state enabled

  6. Create Zone.

    Code Block
    languagenone
    set addressContext a1 zone LYNC_ZONE id 2
set addressContext a1 zone LYNC_ZONE domainName sbc.domain.com

  7. Create SIP Signaling Port.

    Code Block
    languagenone
    set addressContext a1 zone LYNC_ZONE id 2 sipSigPort 2 ipInterfaceGroupName LIF1 ipAddressV4 10.10.10.11 portNumber 5060 
transportProtocolsAllowed sip-tcp state enabled mode inService

  8. Create External DNS Group or local DNS group.

    Code Block
    languagenone
    # Configuring External DNS Group
set addressContext a1 dnsGroup EXT_DNS
set addressContext a1 dnsGroup EXT_DNS type mgmt server DNS1 ipAddress 10.10.10.10 state enabled
set addressContext a1 zone LYNC_ZONE dnsGroup EXT_DNS

# Configuring Local DNS Group
set addressContext a1 dnsGroup LOCAL_DNS
set addressContext a1 dnsGroup LOCAL_DNS localRecord DNS1 hostName lync.domain.com data 1 ipAddress 10.10.10.22 state enabled
set addressContext a1 dnsGroup LOCAL_DNS localRecord DNS1 hostName lync.domain.com data 2 ipAddress 10.10.10.23 state enabled
set addressContext a1 dnsGroup LOCAL_DNS localRecord DNS1 hostName lync.domain.com order roundrobin state enabled
set addressContext a1 dnsGroup LOCAL_DNS localRecord DNS1 state enabled

set addressContext a1 dnsGroup LOCAL_DNS localRecord DNS2 state enabled hostName med1.domain.com data 1 ipAddress 10.10.10.22 state enabled
set addressContext a1 dnsGroup LOCAL_DNS localRecord DNS3 state enabled hostName med2.domain.com data 1 ipAddress 10.10.10.23 state enabled
    Note

    You can configure centralized round-robin or strict round-robin for first-come first-served basis. Centralized round-robin is not recommended for high call traffic volume.

    For distributed round-robin over a large volume of traffic, configure the following:

    set addressContext a1 dnsGroup LOCAL_DNS localRecord DNS1 hostName lync.domain.com order roundrobin state enabled

  9. Create SIP Trunk.

    Code Block
    languagenone
    set addressContext a1 zone LYNC_ZONE sipTrunkGroup LYNC_TG media mediaIpInterfaceGroupName LIF1
set addressContext a1 zone LYNC_ZONE sipTrunkGroup LYNC_TG policy media packetServiceProfile LYNC_PSP
set addressContext a1 zone LYNC_ZONE sipTrunkGroup LYNC_TG policy signaling ipSignalingProfile LYNC_IPSP
set addressContext a1 zone LYNC_ZONE sipTrunkGroup LYNC_TG downstreamForkingSupport enabled
set addressContext a1 zone LYNC_ZONE sipTrunkGroup LYNC_TG signaling rel100Support enabled
set addressContext a1 zone LYNC_ZONE sipTrunkGroup LYNC_TG services dnsSupportType a-only
set addressContext a1 zone LYNC_ZONE sipTrunkGroup LYNC_TG ingressIpPrefix 10.10.10.0 24
set addressContext a1 zone LYNC_ZONE sipTrunkGroup LYNC_TG policy featureControlProfile LYNC_FCP
set addressContext a1 zone LYNC_ZONE sipTrunkGroup LYNC_TG signaling acceptHistoryInfo enabled
set addressContext a1 zone LYNC_ZONE sipTrunkGroup LYNC_TG mode inService state enabled

  10. Create IP Peer.

    Code Block
    languagenone
    set addressContext a1 zone LYNC_ZONE ipPeer LYNC_IPP
set addressContext a1 zone LYNC_ZONE ipPeer LYNC_IPP policy sip fqdn lync.domain.com fqdnPort 5068
set addressContext a1 zone LYNC_ZONE ipPeer LYNC_IPP pathCheck profile LYNC_OPTIONS hostName lync.domain.com hostPort 5068 state enabled

  11. Create Static Route

    Code Block
    languagenone
    set addressContext a1 staticRoute 10.10.10.22 32 10.10.10.1 LIF1 PKT0_V4 preference 100
Info

If you are using IPv6 addressing, then Static Route, IP Peer and Ingress IP Prefix needs to be configured as per IPv6 addressing scheme.

Below is an example of IP interface group and SIP signaling port configuration in the Lync Side using IPv6 addressing scheme:

Code Block
languagenone
titleExample IP interface group and SIP signaling port configuration:
###Create IP Interface Group
set addressContext a1 ipInterfaceGroup LIF1 ipInterface PKT0_V4 altIpAddress fc00::10:f:f:f:11 altPrefix 64

###Create SIP Signaling Port
set addressContext a1 zone LYNC_ZONE id 2 sipSigPort 2 ipAddressV6 fc00::10:f:f:f:11

Configuration in the Service Provider Side (SP Network)

There is no specific parameters to be set on Service Provider side hence standard trunkgroup creation procedure needs to be followed based on deployment. The below provides example configuration.

Note

To play LRBT, apply 'Tones and Announcement' profile on trunk group as appropriate.

 

  1. Create Packet Service Profile.

    Code Block
    languagenone
    set profiles media packetServiceProfile SP_PSP
set profiles media packetServiceProfile SP_PSP codec codecEntry1 G711_2833_20
set profiles media packetServiceProfile SP_PSP rtcpOptions rtcp enable
set profiles media packetServiceProfile SP_PSP preferredRtpPayloadTypeForDtmfRelay 101
set profiles media packetServiceProfile SP_PSP silenceInsertionDescriptor g711SidRtpPayloadType 13 heartbeat enable

  2. Create IP Signaling Profile.

    Code Block
    languagenone
    set profiles signaling ipSignalingProfile SP_IPSP
set profiles signaling ipSignalingProfile SP_IPSP commonIpAttributes flags includeReasonHeader enable
set profiles signaling ipSignalingProfile SP_IPSP commonIpAttributes flags sendPtimeInSdp enable
set profiles signaling ipSignalingProfile SP_IPSP commonIpAttributes flags sendRtcpPortInSdp enable
set profiles signaling ipSignalingProfile SP_IPSP egressIpAttributes flags disable2806Compliance enable
set profiles signaling ipSignalingProfile SP_IPSP ingressIpAttributes flags sendSdpIn200OkIf18xReliable enable

  3. Create IP Interface Group.

    Code Block
    languagenone
    set addressContext a1 ipInterfaceGroup LIF2 ipInterface PKT1_V4 ipAddress 20.20.20.11 prefix 24
set addressContext a1 ipInterfaceGroup LIF2 ipInterface PKT1_V4 ceName LYNCSBC portName pkt1
set addressContext a1 ipInterfaceGroup LIF2 ipInterface PKT1_V4 mode inService state enabled

  4. Create Zone.

    Code Block
    languagenone
    set addressContext a1 zone SP_ZONE id 3

  5. Create SIP Signaling Port.

    Code Block
    languagenone
    set addressContext a1 zone SP_ZONE id 3 sipSigPort 3 ipInterfaceGroupName LIF2 ipAddressV4 20.20.20.11 
portNumber 5060 transportProtocolsAllowed sip-tcp,sip-udp state enabled mode inService

  6. Create SIP Trunk.

    Code Block
    languagenone
    set addressContext a1 zone SP_ZONE sipTrunkGroup SP_TG media mediaIpInterfaceGroupName LIF2
set addressContext a1 zone SP_ZONE sipTrunkGroup SP_TG policy media packetServiceProfile SP_PSP
set addressContext a1 zone SP_ZONE sipTrunkGroup SP_TG policy media toneAndAnnouncementProfile LRBT_PROF
set addressContext a1 zone SP_ZONE sipTrunkGroup SP_TG policy signaling ipSignalingProfile SP_IPSP
set addressContext a1 zone SP_ZONE sipTrunkGroup SP_TG ingressIpPrefix 20.20.20.0 24
set addressContext a1 zone SP_ZONE sipTrunkGroup SP_TG mode inService state enabled

  7. Create IP Peer.

    Code Block
    languagenone
    set addressContext a1 zone SP_ZONE ipPeer SP_IPP
set addressContext a1 zone SP_ZONE ipPeer SP_IPP ipAddress 20.20.20.22 ipPort 5060

  8. Create Static Route.

    Code Block
    languagenone
    set addressContext a1 staticRoute 20.20.20.22 32 20.20.20.1 LIF2 PKT1_V4 preference 100

Global Call Routing Configuration

The following is the global call routing configuration:

  1. Create Routing Labels.

    Code Block
    languagenone
    set global callRouting routingLabel LYNC_RL routingLabelRoute 1 trunkGroup LYNC_TG ipPeer LYNC_IPP inService inService
set global callRouting routingLabel SP_RL routingLabelRoute 1 trunkGroup SP_TG ipPeer SP_IPP inService inService

  2. Create Routes.

    Code Block
    languagenone
    set global callRouting route none Sonus_NULL Sonus_NULL standard 10 1 all all ALL none Sonus_NULL routingLabel LYNC_RL
set global callRouting route none Sonus_NULL Sonus_NULL standard 20 1 all all ALL none Sonus_NULL routingLabel SP_RL
set global callRouting route none Sonus_NULL Sonus_NULL username Sonus_NULL Sonus_NULL all all ALL none med1.domain.com routingLabel LYNC_RL
set global callRouting route none Sonus_NULL Sonus_NULL username Sonus_NULL Sonus_NULL all all ALL none med2.domain.com routingLabel LYNC_RL

Pagebreak