Add_workflow_for_techpubs | ||||||||||
---|---|---|---|---|---|---|---|---|---|---|
|
Panel | ||||
---|---|---|---|---|
In this section:
|
Info |
---|
Related articles: |
Use this object to configure ENUM service.
Use the ENUM Service window to create an ENUM Service object for the SBC and set its initial parameters. After you create the object you can configure additional options for the ENUM Service object using the ENUM Service - Criteria, ENUM Service - ENUM Definitions, and ENUM Service - Flags windows.
Info | ||
---|---|---|
| ||
To support ENUM services for the SBC in ERE mode, manually create an ACL rule |
...
for the ENUM server to allow |
...
packets (ENUM responses) from the ENUM server into the SBC. |
...
Set the Fill Rate for the rule to a higher value (for example, Fill Rate = 2000) to support high ENUM call loads (more than 20 cps). See Ip Access Control List - Rule for configuration details. |
...
On the SBC main screen, go to Configuration > System Provisioning > Category: Call Routing > Servers >
...
Caption | ||||
---|---|---|---|---|
| ||||
|
To edit any of the Enum Service in the list, click the radio button next to the specific Enum Service name.
Caption | ||||
---|---|---|---|---|
| ||||
|
ENUM Service or
All > Global > Servers > ENUM Service
The ENUM Service window opens
...
.
Caption | |||
---|---|---|---|
|
...
| |
|
...
To create a
...
Caption | ||||
---|---|---|---|---|
| ||||
|
new ENUM Service object:
Click New ENUM Service. The Create New ENUM Service window opens
...
.
Caption | |||
---|---|---|---|
|
...
| |
|
...
Caption | ||||
---|---|---|---|---|
| ||||
|
...
|
...
|
...
|
...
|
...
|
...
|
...
For example, setting CNAM priority to 133 executes SIP AoR before CNAM.
|
To copy an ENUM Service object:
...
...
Caption | ||||
---|---|---|---|---|
| ||||
|
Click Copy Enum Service tab on the Enum Service List panel.
Caption | ||||
---|---|---|---|---|
| ||||
|
The Copy Selected Enum Service window is displayed along with the field details which can be edited.
Caption | ||||
---|---|---|---|---|
| ||||
|
The following fields are displayed:
...
0 | Table |
---|---|
1 | Enum Service Copy Parameters |
...
Name
...
Specify the name of the enum server.
...
Default
Treatment
...
Select the default treatment for request timeout:
Route As Dialed
Apply Final Treatment
...
Service Type
...
Select the type of DNS/ENUM service:
CNAM
LNP
SIP AoR
...
Request Time
Out
...
The request timeout value in seconds. This value supersedes the request timeout value.
...
Specifies whether to enable enumeration or not. The options are:
enable
disable
(default)...
Enable this flag to analyze the calling number using prefix profile.
When this flag is disabled, the calling number is not analyzed and hence if it has +CC, the same is sent as-is to SBC in the calling number field in policy response. The options are:
enable
disable
(default)To edit an ENUM Service object:
To delete an ENUM Service object:
Pagebreak |
---|
...
When this flag is enabled for ENUM AoR service, and ENUM AoR response contains "newani=<some_number>
" parameter in NAPTR record, the ERE overwrites the existing calling number of the call with the newANI
number.
When this flag is disabled, any newANI
parameters received in NAPTR response are ignored in PES. The options are:
enable
disable
(default)...
Make the required changes to the required fields and click Save to save the changes. The copied Enum Service is displayed at the bottom of the original Enum Service in the Enum Service List panel.
To delete any of the created Enum Service, click the radio button next to the specific Enum Service which you want to delete.
Caption | ||||
---|---|---|---|---|
| ||||
|
Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.
Caption | ||||
---|---|---|---|---|
| ||||
|
...