Page History

This section describes how to create initial, basic configuration on a signaling SBC (S-SBC) SWe Cloud cluster using the SBC Configuration Manager GUI. Although the following procedures use the GUI, you can also make cluster configuration changes using the CLI on the OAM node. Refer to Modifying SBC Cluster Configuration for information on using the CLI and the CLI Reference Guide for information on the available commands.

The configuration shown here is a basic example and focuses on minimum configuration required for a basic call flow and configuration required by cloud-based clusters. As part of a distributed SBC cloud deployment, an S-SBC cluster must be paired with a media (M-SBC) cluster to provide full SBC functionality. Both cluster configurations include a D-SBC signaling port to allow communication between the two clusters. 

In contrast to assigning static values, cloud deployments use metavariables to assign interface values such as IP addresses. The actual values are determined dynamically during instantiation, based on the cloud environment. 

Beyond this minimal configuration, a full deployment would require further configuration and customization based on the intended use and environment, similar to other types of SBC deployments.

Prerequisites

• The S-SBC cluster configuration must be created in the Insight EMS and configured with a Configuration Type of OAM. Refer to Creating an SBC Cluster and SBC SWe Configuration Management Using OAM Nodes.
• The S-SBC cluster, including its OAM nodes, must be instantiated using either VNFM or the Heat template method of deployment. Refer to Instantiating SBC SWe Using a Heat Template or Instantiating SBC SWe on OpenStack using VNFM.  

Accessing the SBC Configuration Manager

Begin the process to initially configure a new S-SBC cluster by accessing the SBC Configuration Manager for the cluster.

1. Log on to the EMS.

2. Click Network > Cluster Management. The Cluster Management / Manage VNFs window opens listing the SBC clusters registered with the EMS

1. .

   Caption
   0 Figure 1 Cluster Management / Manage VNFs window

1. Image Added

   
   

2. Click the radio button adjacent to the name of the S-SBC cluster you want to configure. The Details tab for the selected cluster opens. 

3. Click the Configurations tab. 

   Caption
   0 Figure 1 Cluster Configurations Tab
   Image Added

   
   

4. Click Edit Configuration. The SBC Configuration Manager opens in a separate window against the cluster's active OAM node. See the EMA User Guide for information on using the GUI to configure the SBC.

   Caption
   0 Figure 1 SBC Configuration Manager Window
   Image Added

   
   

Configure the SBC using the SBC Configuration Manager

Use the following procedures and examples to configure basic S-SBC parameters using the

SBC Configuration Manager.

1. To validate the meta variable table,

1. see Validating the Meta Variable Table.

1. To create an address context, see Create an Address Context.

2. To create IP interface

1. groupa and

1. IP

1. interfaces,

1. see Creating

1. IP Interface

1. Groups and

1. IP

1. Interfaces.

2. To create a static route,

1. see Create a Static Route.
2. To create a DNS group and a DNS server,

1. see Create a DNS Group and a DNS Server.

1. To create a NTP server,

1. see Create an NTP Server.

1. To create the D-SBC

1. signaling port, see Create the D-SBC

1. Signaling Port.
2. To create a cluster type,

1. see Create a Policer Cluster Type.
2. To create

1. zones, see Create Zones.
2. To create SIP

1. signaling ports, see Create SIP Signaling Ports.
2. To create SIP trunk

1. groups,

1. see Create SIP Trunk

1. Groups.
2. To create a remote policy server, see Configuring a Remote Policy Server

1. .

Anchor
meta_variable meta_variable

Validating the Meta Variable Table

To validate the

values assigned to metavariables during instantiation, review the Meta Variable table by clicking All > System > Meta Variables. The Meta Variable

window opens showing the Meta Variable list. In cloud deployments, metavariables are used to assign interface values, such as IP addresses, whose values are configured dynamically during instantiation.

Anchor

AddressContext

AddressContext

Create an

Address Context

Some of the following procedures require that you specify an address context in which to create configuration objects. The following procedures use an example address context named AC2 as a placeholder. In actual practice you can specify your own address context name or use the default address context. The following steps create an address context named AC2. 

1. Click Configuration > System Provisioning > Category: Base Provisioning >Address Context. The Address Context window opens.
2. Click New Address Context. The Create New Address Context window opens.
3. Enter AC2 as the name of the address context (the name must be between 1-23 characters in length). 
4. Click Save.

Anchor
step1 step1

Create IP Interface Groups and IP Interfaces

Create IP Interface Groups

1. Select

1. Address Context > IP Interface Group.

1. The IP Interface Group

1. List window opens.

1. Select AC2 from

1. the Address Context drop-down

1. list.

1. Click New IP Interface Group.

1. The Create New IP Interface

1. Group window opens.

2. Enter an IP interface group name

1. .

1. Click Save.

   Caption
   0 Figure 1 IP Interface Group 3 IP Interface Group
   Image Modified

Repeat the previous steps to create another interface group. Example: SLIG2. The two new interface groups are listed.

IP

Interfaces for each Pkt Port

1. On the navigation pane, click Address Context > IP Interface Group > IP Interface.

1. The IP Interface window opens.

1. Select AC2 from the Address Context drop-down

1. list.
2. Select an interface group created from the IP Interface Group drop-down

1. list. For example, SLIG1.
2. Click

1. New IP Interface.

1. The Create New IP

1. Interface section opens.
2. Enter a name for the interface. For example, SLIF1.
3. Enter IP Meta

1. variable keys in the IP Var V4, Prefix Var V4, IP Public Var V4, IP Var V6, IP Prefix Var V6, IP Public Var V6, and IP VLAN Tag Var fields.

1. Select the Mode as In Service.

1. Select the State as Enabled.
2. Enter the CE Name

1. .

1. Select the pkt0 port from the Port Name drop-down menu.

2. Click Save.

1. Caption
   0 Figure 1 Creating an IP Interface
   Image Modified

Repeat the previous steps to add an

interface

SLIF2 for pkt1 port in a different Interface Group SLIG2. The two interfaces are listed.

1. window opens.

1. Select the AC2 Address Context from the drop-down list.
2. Click 

1. New Static Route.

1. The Create New Static Route window opens.
2. Enter the Destination IP Address (IPv4/IPv6).
3. Enter the Prefix value.
4. Enter the Next Hop IP

1. address (IPv4/IPv6).
2. Select

1. an IP Interface Group Name from the drop-down

1. list.
2. Select

1. an IP Interface Name from the drop-down

1. list.
2. Enter

1. a Preference

1. value

1. .

2. Click Save.

1. Caption
   0 Figure 1

1. Static Route Window 3 Static Route

   Image Modified

Anchor
step2 step2

Create a DNS Group and a DNS Server

Create a

DNS Group

1. Select Address Context > DNS Group.

1. The DNS Group window opens.
   
2. S

1. elect AC2 from the Address Context drop-down

1. list.
   
2. Click 

1. New DNS Group.

1. The Create New DNS

1. Group section opens.
   
2. Enter a DNS group name.
   
3. Select IP from the Type drop-down

1. list.
   
2. Select 

1. SLIG1 from the IP Interface drop-down

1. list.
   
2. Select Use Configured Dns

1. Server and Edns Support as Enabled.
   

2. Click Save.
   

   Caption
   0 Figure 1

1. Create New DNS Group

   Image Modified

Create a DNS Server

1. Select Address Context > DNS Group > Server.

1. The Server window opens. 

2. On the Server window, perform the following:

   1. Select AC2

1. 1. from the Address Context drop-down

1. 1. list.

   2. Select the DNS group

1. 1. you created from

1. 1. the DNS Group

1. 1. drop-down

1. 1. list. 
      

   2. Click

1. 1. New Server.

1. 1. The Create New Server

1. 1. section opens.

1. 1. In the Create New Server section:

      1. Enter a server name.

1. 1. 1. Select the State as Enabled.
         

      2. Enter the DNS server IP in the

1. 1. 1. IP Address V4 or V6

1. 1. 1. field.

1. 1. 1. Click Save.

Anchor
step3 step3

Create

an NTP Server

1. Select System > NTP > Server Admin.

1. The Server Admin window opens.

2. Click

1. New Server Admin.

1. The Create New Server Admin

1. section opens.
2. Enter a server IP address.

1. Select the State

1. as Enabled.

1. Select the Version

1. as Version4.

1. Click Save.

   Caption
   0 Figure 1 NTP Server Admin
   Image Modified

1. 
   

2. Select System > NTP > Time Zone.

1. The Time Zone window opens.

2. Select the instance from the list.

1. The Edit Selected Time

1. Zone section opens.

2. Select an appropriate time zone from the Zone drop-down

1. list.

2. Click Save.

Anchor
step4 step4

Create the D-SBC

Signaling Port

Create a D-SBC

signaling port for communication with the M-SBC cluster in the deployment:

1. Select System > Dsbc > Dsbc Sig Port.

1. The Dsbc Sig Port

1. window opens.
2. Select 

1. SLIG1 from the IP Interface Group drop-down list.
2. Select AC2 from the Address Context drop-down

1. list.
2. Click Save.

Anchor
step5 step5

Create a Policer Cluster Type

1. Select System > Dsbc > Cluster > Type.

1. The Type window opens.

2. Click

1. New Type. The Create New Type section displays.

2. Select the Name as Policer.
3. Select State as Enabled.

4. Enter the cluster FQDN.

1. Info
   title Note:
   The floating IP address of packet interfaces

1. is added as

1. a record in DNS server.

   
   

2. Select the name of the DNS group

1. you created in the DNS Group drop-down

1. list.
2. Click Save.

Anchor
step6 step6

Create

Zones

1. Select Address

1. Context > Zone. The

1. Zonewindow opens.

2. Select

1. AC2 from the Address Context drop-down

1. list.

2. Click 

1. New Zone.

1. The Create New

1. Zone section

1. opens.

2. Enter a Name

1. for the zone, for example, INTERNAL.
2. Enter

1. an ID for the zone.

2. Click Save.

   Caption
   0 Figure 1

1. Create New Zone

   Image Modified

Repeat the previous steps

to create another zone

, for example, EXTERNAL. The new zones are listed.

SIP

Signaling Ports

Create SIP signaling ports for the zones you created:

1. Select Address Context > Zone > SIP Sig Port. The SIP

1. Sig Port window opens.
2. Select

1. AC2 from the Address Context drop-down

1. list.
2. Select

1. the INTERNAL zone from the Zone drop-down

1. list.
2. Click

1. New SIP Sig Port. The Create New SIP Sig Port section

1. opens.
2. Enter an Index number.
3. Set the State as Enabled.
4. Select SLIG1 from the IP Interface Group Name drop-down

1. list.
2. Select the sip-

1. udp option in the Transport Protocols Allowed.

2. Click Save.

   Caption
   0 Figure 1

1. Create New SIP

1. Sig Port 3 SIP SigPort

   Image Modified

Repeat the previous steps

to create

a SIP signaling port for the EXTERNAL zone. The new SIP

signaling ports are listed.

Anchor
step8 step8

Create

SIP Trunk

Groups

Create

SIP trunk

groups in the the zones you created:

1. Select Address Context > Zone > SIP Trunk Group.

1. The SIP Trunk Group

1. window opens.
2. Select AC2

1. from the Address Context drop-down

1. list.
2. Select a INTERNAL zone from the Zone drop-down

1. list.
2. Click

1. New SIP Trunk Group.

1. The Create New SIP Trunk

1. Group section opens.
2. Enter

1. a Name for the trunk group, for example, INGRESS_TG.
2. Set the State as Enabled.
3. Set the Mode as In Service.

4. Click Save.

   Caption
   0 Figure 1 Creating a SIP Trunk Group
   Image Modified

Repeat the previous steps

to create another SIP trunk group for the EXTERNAL zone. The new SIP trunk groups are listed.

Prefixes

Create ingress IP prefixes for the SIP trunk groups you created:

1. Select Address Context > Zone > SIP Trunk Group > Ingress IP Prefix.

1. The Ingress IP Prefix

1. window opens.

1. Select AC2 from the Address Context drop-down menu.
2. Select

1. the INTERNAL zone from the Zone drop-down menu.

2. Select the INGRESS_TG trunk group from the SIP Trunk Group drop-down

1. list.
2. Click 

1. New Ingress IP Prefix. 

1. The Create New Ingress IP

1. Prefix section opens.
2. Enter

1. an IP address in IP Address V4 or V6.
2. Enter the Prefix Length.

3. Click Save.

   Caption
   0 Figure 1 Create New Ingress IP Prefix
   Image Added

   
   

Repeat the previous steps to create an IP Prefix for the EXTERNAL zone and EGRESS_TG trunk group. The new IP prefixes are listed.

Anchor
Step10 Step10

Configure Media

Settings

Configure media settings for the SIP trunk groups you created:

1. Select Address Context > Zone > SIP Trunk Group > Media.

1. The Media window opens.

1. Select AC2 from the Address Context drop-down

1. list.
2. Select

1. the INTERNAL zone from the Zone drop-down

1. list.
2. Select the INGRESS_TG trunk group from the SIP Trunk Group drop-down

1. list.
2. Select MLIG1 from the Media IP Interface Group Name drop-down

1. list.
2. Click Save. 

Anchor

step11

step11

Configuring the Remote Policy Server

Configure the settings for the remote PSX server:

Disable the Local Policy Server

1. Select System > Policy Server > Local Server. The Local Server

1. window opens.

2. Select the local server listed. The Edit Selected Local Server section

1. opens.

2. Set the State as Disabled.

3. Select Out of Service from the Mode drop-down menu.

4. Click Save. 

Create a New Remote Policy Server

1. Select System > Policy Server > Remote Server.

1. The Remote Server window opens. 

2. Click

1. New Remote Server.

1. The Create New Remote

1. Server section opens.

2. Enter

1. a server Name. 

2. Enter the server IP Address.

1. Set the State as Enabled. 

1. Select Active from the Mode drop-down

1. list.

2. Click Save.

   Caption
   0 Figure 1

1. Create New Remote

1. Server

   Image Modified

   
   

Saving and Activating the Configuration in the Cluster

Once you have completed making configuration changes, click Apply Saved Changes and Close at the top-right of the SBC Configuration Manager window. When prompted, confirm that you want to save and activate your configuration changes. The SBC Configuration Manager window closes. The OAM node notifies the SBC nodes in the cluster of the configuration changes and stores a record of the updated configuration back to the EMS.