Page History
| Panel |
|---|
...
| borderColor | green |
|---|---|
| bgColor | transparent |
| borderWidth | 2 |
...
| Noprint |
|---|
| Back to Configuration - System Provisioning |
Additional sections:
| Children Display | ||
|---|---|---|
|
| Panel | ||||
|---|---|---|---|---|
In this section:
|
...
In this section:
|
| Info | ||
|---|---|---|
| ||
Related articles:
|
Use this section to specify the IP interfaces that the
...
| Spacevars | ||
|---|---|---|
|
To View
...
IP Interface
On
...
the
| Spacevars | ||
|---|---|---|
|
...
IP Interface Group >
...
IP Interface. The
...
IP Interface window
...
displays.
| Caption | |||||
|---|---|---|---|---|---|
|
...
| |
 |
...
This window can display a listing of IP Interfaces for each Address Context
...
, for each
...
IP Interface Group or for all
...
existing Address Contexts and
...
IP Interface Groups
...
. Use the drop-down
...
menus at the top of the page to select the
...
Address Contexts and
...
/or IP Interface Groups of interest.
| Caption | |||
|---|---|---|---|
|
...
| |
 |
...
...
Edit
...
an IP Interface
To edit
...
an IP Interface in the list, click the radio button next to the
...
IP Interface name of interest.
| Caption | |||
|---|---|---|---|
|
...
| |
 |
...
The Edit Selected
...
IP Interface window is displayed below.
| Caption | |||
|---|---|---|---|
|
...
| |
 |
Make the required changes and click Save at the right hand bottom of the panel to save the changes made.
...
Create
...
an IP Interface
To create a new
...
IP Interface, click New
...
IP Interface tab on the
...
IP Interface List panel.
| Caption | |||
|---|---|---|---|
|
...
|
...
| |
 |
The Create New
...
IP Interface window is displayed.
| Caption | |||
|---|---|---|---|
|
...
| |
 |
...
The following fields are displayed:
| Caption | |||
|---|---|---|---|
|
...
|
...
Parameter | Description |
|---|---|
Name | The IP interface name. |
| Mode | The operational state of the IP Interface:
|
...
Note: When setting |
...
| |
| State | The administrative state of the IP Interface:
|
...
CE Name | The name of the |
...
computing element (1 - 255 characters) that hosts the port used by |
...
the IP interface. |
| Note |
|---|
Ce Name is currently not used by the SBC. |
Port Name | The physical port name (example: pkt0, ..., pkt3) used by this IP interface. | ||
IP Address | The IP address of the Interface. | ||
Prefix | The IP subnet prefix of this Interface. | ||
Alt IP Address | Specifies alternative (secondary) IP address for the configured packet IP interface. The alternative IP address is optional.
| ||
| Alt Media Ip Address | Use this parameter to specify up to 14 additional IPv4 and/or IPv6 media IP addresses on this IP interface. Any combination of IPv4 and IPv6 is allowed. The following rules apply when configuring alternate media IP addresses:
|
| Note |
|---|
This parameter is only visible on the SBC 7000 platform. |
Alt Prefix | The alternative IP subnet prefix of this Interface. It should be between 0-128. |
Action | The method by which calls are torn down when operational state goes to out of service:
|
Dryup Timeout | The |
...
dry-up timeout in minutes (e.g. the number of minutes to wait before taking the interface out of service). This is started at the point where the command to make the interface out of service is issued. This is only applicable for media traffic, if there is no media traffic on the interface then it is immediately taken out of service. Range: 0-1440 (minutes) |
...
. Default = 60. | |
Bw Contingency | The percentage of maximum bandwidth that is reserved for contingency (that is, non-media). Value must be 0-100 percent. |
Vlan Tag |
...
Assign a VLAN ID |
...
to each IP Interface |
...
which |
...
will |
...
include one or more SUBINTERFACEs |
...
. When the parent IP Interface is created, this parameter is assigned the NULL (0) tag. When the IP Interface is enabled for VLAN TAG STATE, in order to provision a SUBINTERFACE, this parameter must already be set to a value in the |
...
2-4094 |
...
range |
...
or the enable command will fail. |
...
|
...
A VLAN ID |
...
in the |
...
range cited above |
...
must also be assigned to each IP Interface when it is configured. This value must be unique |
...
on a physical port.
| ||||||
Bandwidth | Specifies the maximum amount of bandwidth allowed in units of bytes per second. Must be 0-118750000 as follows: |
Enter all the required fields.
...
| Tip | ||
|---|---|---|
| ||
Click Show only required fields |
...
at the bottom left-hand |
...
portion of the panel to view and enter only the required fields to create a |
...
IP Interface. |
...
Delete
...
an IP Interface
To delete any of the created
...
IP Interfaces, click the radio button next to the specific
...
IP Interface which you want to delete.
| Caption | |||
|---|---|---|---|
|
...
| |
| |
...
Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.
| Caption | |||
|---|---|---|---|
|
...
| |
 |
...
Click
...
Yes to remove the specific
...
IP Interface from the list.
| Pagebreak |
|---|
Overview
Content Tools