Page History

Overview

The

IPsec protocol suite as defined in the table below.

The Sonus IP Security (

IPsec) feature provides cryptographic protection by the application of

IPsec on a packet-by-packet basis controlled by rules in a Security Policy Database (SPD). These rules are applied to each incoming and outgoing packet, and as a function of source IP address, destination IP address, protocol, source port and destination port produce a directive to discard the packet, bypass the packet (allow it to pass as plaintext), or protect the packet with

IPsec according to parameters specified in

IPsec Protection Profile.

IPsec is implemented using Encapsulating Security Payload (ESP) encapsulation.

During

IPsec configuration, a single IP SECURITY POLICY instance is created and assigned to the interfaces group. The IP SECURITY POLICY contains the following databases:

• Security Policy Database (SPD)—An ordered list of "rules" built and configured by operators that specify the type of protection to provide for each packet that is subjected to the rule.
• Internet Key Exchange (IKE) Peer Database (IPD)—A list of peer devices built and configured by operators that defines eligibility and authentication data for protected sessions using

• IPsec.
• Security Association Database (SAD)—The list of active Security Associations (SAs) created from successful

• IPsec negotiations between

• the

  Spacevars
  0 series4

   and protected peers. Each SA is the bundle of algorithms and parameters used to encrypt and authenticate a particular flow in one direction. Thus for normal bidirectional traffic, the flows are secured by a pair of security associations. This list is system rather than operator generated.

Each SPD entry (or rule) identifies local and remote peer transport addresses that apply. This entry also establishes three packet protection actions:

• DISCARD—discard the packet
• BYPASS—pass the packet on without modification
• PROTECT—encrypt the packet according to an encryption algorithm that has been mutually agreed to by the session peers

The SPD entry PRECEDENCE establishes that entry's order relative to other entries from 1 to 65535. Each SPD entry references up to three

IPsec Protection Profiles that specify an encryption cipher, a maximum time period for maintaining a security association between these peers (the SA "lifetime"), and an anti-replay policy. The three profiles are prioritized from 1 to 3 for use with the SPD entry.

Each IPD entry specifies a remote peer address to use for a protected session. The IPD entry also contains a PRESHARED SECRET (text string), and local and remote identification information. These parameters are all used in the peer-to-peer authentication process. As with SPD entries, IPD entries also reference up to three prioritized IKE Protection Profiles. The IKE profiles specify an encryption cipher, a maximum time period for maintaining security associations, and abandon-session-because-of-error policies. These profiles are also prioritized from 1 to 3 for usage with the IPD entry.

For

IPsec Peer configuration details, see Ipsec - Peer (EMA) or

IPsec Peer - CLI.

IKEv1 Negotiation

An

IPsec SA is the result of a successful two stage negotiation between the

IPsec SA pair (two unidirectional SAs) that the peers may use to protect IP traffic between them until the IPsec SA expires or is removed.

In the IKE phase 1 exchange, the PRESHARED SECRET is used by the peers to authenticate one another. In the IKE phase 2 exchange, the packet selectors, the encryption cipher, the integrity cipher, and the SA lifetime are negotiated. If there is a valid intersection between the peers for all of these parameter values, then the phase 2 negotiation is successful and an

IPsec SA will result.

When the negotiation is initiated by the peer, the

the

IPsec SA pair that defines a protection scheme for packets flowing between the SIP peer and SBC is established.

When

the

IPsec SA pair that defines the protection scheme for packets flowing between SBC and the SIP peer.

The following table depicts the impact of 'pfsRequired' state to Quick Mode exchange based on

the 

IKEv2 Support

IKEv2 performs mutual authentication between the

1. A set of cryptographic algorithms used by the SAs to protect the traffic between

1. the

   Spacevars
   0 series4

    and the peer
2. CHILD-SAs for Encapsulated Security Payload (ESP) Protocol

All IKE communications consist of pair of messages – a request and a response. The pair is also referred as an exchange. The first exchanges of messages establishing an IKE SA are called the IKE_SA_INIT and IKE_AUTH exchanges; subsequent IKE exchanges are called the CREATE_CHILD_SA or INFORMATIONAL exchanges.

• IKE_SA_INIT: This exchange performs the following functions:

• 1. Negotiates cryptographic algorithms for the IKE-SA
  2. Exchanges nonces
  3. Diffie-Hellman exchange

After this exchange, the

• IKE_AUTH: This exchange performs the following functions:

• 1. Exchanges identities
  2. Proves knowledge of the secrets related to those identities
  3. Sets up an SA for the first ESP Child SA (

• 1. IPsec SA pair)

The

• CREATE_CHILD_SA: This exchange creates new/additional Child SAs and re-keys both IKE SAs and Child SAs.
• INFORMATIONAL: This exchange performs the following functions:
  
  1. Deletes SAs as needed
  2. Reports error conditions
  3. Checks liveliness of the other endpoint

Once the first two mandatory exchanges have completed in their proper order, all subsequent exchanges can occur in any order as necessary. In the common case, there is a single IKE_SA_INIT exchange and a single IKE_AUTH exchange (a total of four messages) to establish the IKE SA and the first Child SA. In exceptional cases, there may be more than one of each of these exchanges.

The following table depicts the impact of 'pfsRequired' state to CREATE_CHILD_SA Exchange based on

IPSEC SA re-key:

SA Removal

SAs are removable before their lifetime expires using the following methods:

• Globally delete every IKE SA (DELETE...ALL)
• Delete a specific IKE SA by its IKE handle identifier (DELETE...IKE ID...)
• Delete the

• IPsec SA pair with a given incoming Security Parameter Index value (LOCAL SPI)

SAs are also removable through notification by the peer that an SA is deleted, or as a result of Dead Peer Detection determining that a peer is unresponsive.

If an SA is deleted by one of the above scenarios within 60 seconds of the time that it was initially established, then as a Denial-of-Service protection the

Anchor
InitiatorResponder InitiatorResponder

Initiator and Responder Behavior