Page History

The SBC 5400 Hardware Platform comes with three modes of media port configurations. The

2 x 1 Gbps interface mode does not require a license and is enabled by default. For the rest of the interface modes, appropriate licenses should be purchased from Sonus.

The following table provides the complete interface modes and its required licenses.

2 x 1 Gbps or 4 x 1 Gbps to 2 x 10 Gbps Media Interface Upgrade Procedure

This section explains the

procedure to upgrade the media interfaces in SBC 5400.

Prerequisites

1. Verify the SBC 5400 is

1. running on 05.01.00R000 or higher software version.
2. Procure the required media interface licenses. Refer to

1. SBC 5400 Media Ports and Operational Modes to know the all the media interface licenses.

1. Have ready access to the original and all the subsequent licenses. Refer to SBC 5400 Interface Modes and Media Port Assignments table for the required licenses.
2. Save all of your current configurations for use in the event you want to return to 1 Gbps interface mode of operation (The 1 Gbps configuration cannot be applied/imported to 10 Gbps interface mode).
   Refer to  Saving the SBC Configuration

1. for details about how to save your existing SBC configuration. 
2. Keep the Sonus-approved 10 Gb SFPs ready for each of the SBC 5400 systems identified for this Media Interface change.

Procedure

The following procedure is applicable only when you upgrade from

2 x 1 Gbps or 4 x 1 Gbps to 2 x 10 Gbps interface mode.

1. Log on to SBC 5400 BMC GUI

1. .

   Caption
   0 Figure 1 BMC Login Screen
   Image Modified

2. Navigate to Remote Control > Server Power Control. The Power Control and Status window is displayed.

   Caption
   0 Figure 1 SBC 5400 BMC Power Control and Status

1. Window

   Image Modified

2. Select Power Off Server - Orderly Shutdown (preferred) or Power Off Server - Immediate and click Perform Action.

   Caption
   0 Figure 1 SBC 5400 BMC

1. Shut down

   Image Modified

   
   The

1. server and the SBC Application shuts down.

2. Navigate to Configuration > Platform Management Network. The Platform Management Network Settings screen is displayed.

3. Enable the check box Enable 10G Media Speed. This changes the media interface speed from

1. 2 x 1 Gbps or 4 x 1 Gbps to 2 x 10 Gbps.

   Warning

1. This is a service affecting action. The existing configurations will be erased from the SBC.

   A Info window appears stating the existing configuration will be removed.

   Caption
   0 Figure 1 SBC 5400 Media Interface Change Warning Message
   Image Modified

2. Click OK to proceed.

3. Click Save. The new changes are saved. A message is displayed stating the configuration parameters have been set.

   Caption
   0 Figure 1 SBC 5400 Media Interface Change Success Message
   Image Added

4. Click OK to proceed.
5. Remove and store each of the 1 Gb SFPs that are present in the 4 media port slots labeled as Media x where x=0, 1, 2 and 3. Place the Sonus-approved 10 Gb SFP in the Media 0 and Media 2 slots. Refer to Connecting SBC 5400 Ethernet and Data Cables to know more about SFP selection, handling and replacement instructions.
6. Navigate to Remote Control > Server Power Control. The Power Control and Status window is displayed.

7. Select Power On Server. The

1. Server and the SBC Application starts.

2. Once the SBC comes up, log on to the application using the default credentials admin/admin. Change you password immediately to proceed further. Refer to

1. EMA Mode - Login Window to know more about application login credentials.
2. Install the license, "SBC-1X10GMP", on both Active and Standby SBCs.
3. Log on to SBC 5400 Application EMA.

4. Navigate to Monitoring > Dashboard > System Status. The System Status window is displayed. Under the Server Status panel, the Pkt Port Speed column provides the speed of the media interface port.

   Caption
   0 Figure 1 SBC 5400 System Status Speed 10Gbps
   Image Modified

At this stage, the

previous configuration is completely erased. Configure the application as per your needs. Refer to How to Set up a Basic Call Flow to start with

a fresh configuration.

2 x 1 Gbps To

4 x 1 Gbps Media Interface Upgrade Procedure

This section explains the procedures to upgrade the media interfaces in SBC 5400.

Prerequisites

1. Verify the SBC 5400 is running on 05.01.00R000 or higher software version.
2. Procure the required media interface licenses. Refer to SBC 5400 Media Ports and Operational Modes

1. for an explanation of media port speeds and required media interface licenses.

1. For a 2 x 1 Gbps Media Interface, the Media slots 0 and 1 are already occupied with 1 Gb SFPs. Navigate to Monitoring > Dashboard > Ports > Ethernet Ports > Packet Port Status. The Packet Port Status window is displayed. Observe that only the Pkt0 and Pkt1 ports are in Enabled state and the other two are in Disabled state stating no license.

   Caption
   0 Figure 1 SBC 5400 Pkt Port Status for 2X1 Gbps Speed
   Image Added

2. Place the Sonus-approved 1 Gb SFPs in the Media 2 and 3 slots (on both Active and Stanby SBC 5400s). Refer to Connecting SBC 5400 Ethernet and Data Cables to know more about SFP selection, handling and replacement instructions.

Procedure

The following procedure is applicable only when you upgrade from 2x1 Gbps to 4x1 Gbps interface mode.

1. Log on to SBC 5400

1. Application EMA.

2. Add the license, "SBC-4X1GMP", to the SBC 5400 licenses. Refer to SBC Node-Locked Licenses for HW and SWe SBCs to know about adding licenses.

3. Navigate to Monitoring > Dashboard > Ports > Ethernet Ports > Packet Port Status. The Packet Port Status window is displayed.
   The packet ports Pkt2 and Pkt3 are in the enabled state since, the Sonus-approved 1 Gb SFPs are added to Media slots 2 and 3 along with the required license, "SBC-4X1GMP".

   Info
   icon false title Note
   Add the Sonus-approved 1 Gb SFPs and the license: "SBC-4X1GMP", to both Active and Standby SBC 5400s.

1. Caption
   0 Figure 1 SBC 5400

1. Pkt Port Status for 4X1 Gbps Speed

   Image Modified

1. 
   All the four

1. packet ports are

1. enabled with 1 Gbps speed.

1 x 10 Gbps to 2 x 10 Gbps Media Interface Upgrade Procedure

This section explains the procedures to upgrade the media interfaces in SBC 5400 from 1 x 10 Gbps to 2 x 10 Gbps.

Prerequisites

1. Verify the SBC 5400 is running on 07.01.00R000 or higher software version.
2. Keep a Sonus-approved 10 Gb SFP ready for the second 10 Gbps Media Interface of both Active and Standby SBCs.

Procedure

The following procedure is applicable only when you upgrade from 1 x 10 Gbps to 2 x 10 Gbps interface mode:

1. Place a Sonus-approved 10 Gb SFP in the Media 2 slot of both the Active and Standby SBCs and connect the appropriate cables into the packet network. Refer to Connecting SBC 5400 Ethernet and Data Cables to know more about SFP selection, handling and replacement instructions.
2. Configure the SBC application to use second Packet Ethernet interface as desired.