Page History

Warning
Sonus-provided SFP/SFP+ modules must be used to guarantee proper operation of the external ports. Failure to follow this recommendation may cause permanent damage to the system.

Tooltip
tip Use ESD protective device

1 Gb SFP Characteristics

The 

Spacevars
0 series2

supports the following Small Form-factor Pluggable (SFP/SFP+) transceivers. The SFPs (SFP/SFP+) are Customer Replaceable Units (CRU).

The following SFP transceivers are compatible with 

Spacevars
0 series2

Management ports:

Div
class pdf6pttext
Caption 0 Table 1 1Gb SFP Parts 3 1Gb SFP Parts Transceiver Type Product Code SFP Type Manufacturers  Part Number

DescriptionCopper

Wavelength  (nm) Tx Power (dBM) Rx Power (dBM) Description Multi-mode fiber SBC-

SFPCOPPER-1G

SFPMM-1G   1G Ethernet MM AVAGO TECHNOLOGIES AFBR‐5715PZSN1 BROADCOM AFBR‐5715PZ‐SN1 FINISAR FTLF8519P2BNL‐SS FINISAR  FTLF8519P3BNL‐SS 850 -9.5 (Min) -3 (Max) -17 (Min) 0 (Max) GIG-E, MULTIMODE, FIBER OPTIC TRANCEIVER MODULE, LC, SMALL FORM

GIGE, 1000 BASE-T SMALL FROM

PLUGGABLE (SFP), 300M Single-mode fiber  SBC-SFPSM-1G   1G Ethernet  SM AVAGO TECHNOLOGIES AFCT‐5715PZSN1 BROADCOM AFCT‐5715PZSN1 FINISAR FTLF1318P2BTL‐SS FINISAR FTLF1318P3BTL‐SS 1310 -9.5 (Min) -3 (Max) -19 (Min) -3 (Max) GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 10KM 1310NM, DMI

Multi-mode fiber

Copper SBC-

SFPMM

SFPCOPPER-1G

GIG-E, MULTIMODE, FIBER OPTIC TRANCEIVER MODULE, LC, SMALL FORM PLUGGABLE (SFP), 300M

1G Ethernet Copper AVAGO TECHNOLOGIES ABCU-5740RZ-SN1 BROADCOM ABCU-5740RZ-SN1 FINISAR FCLF8521P2BTL-SS NA NA NA NA NA GIGE, 1000 BASE-T SMALL FROM PLUGGABLE (SFP)

Info
title Note
These numbers are taken from Vendor Datasheets as well as IEEE 802.3ae for the 1G parts.

 

10 Gb SFP Characteristics

The following SFP+ transceivers are compatible

with SBC 7000 series

with 

Spacevars
0 series2

Media and HA ports:

Div
class pdf6pttext
Caption 0 Table 1 10Gb SFP Parts 3 10Gb SFP Parts Transceiver Type Product Code SFP Type Manufacturers  Part Number Wavelength  (nm) Tx Power (dBM) Rx Power (dBM) Description

Single

Multi-mode fiber

SBC-SFPSM-10G10.3GB/S, SINGLE MODE

SBC‐SFPMM‐10G 10G Ethernet MM AVAGO TECHNOLOGIES AFBR‐709SMZSN1 BROADCOM AFBR‐709SMZ‐SN1 FINISAR FTLX8571D3BCL‐SS FINISARFTLX8574D3BCL‐SS 850 -7.9 (Min) -1 (Max) -11.1 (Min) 0.5 (Max) 10.3 GB/S, MULTIMODE, FIBER OPTIC XCVR, LC, SFP

, 10KM 1310NM, DMMulti-mode fiberSBC-SFPMM-10G

, 300M 850NM, DMI GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE Single-mode fiber SBC‐SFPSM‐10G   10G Ethernet  SM AVAGO TECHNOLOGIES AFCT‐709SMZSN1 AVAGO TECHNOLOGIES AFCT739SMZ‐SN1 BROADCOM AFCT‐709SMZSN1 BROADCOM AFCT‐739SMZ‐SN1 FINISAR FTLX1471D3BCL‐SS 1310 -8.2 (Min) 0.5 (Max) -12.6 (Min) 0.5 (Max) 10.3 GB/S, SINGLE MODE

10.3GB/S, MULTIMODE

, FIBER OPTIC XCVR, LC, SFP,

300M 850NM, DMI GIG-E, SINGLE MODE, FIBER OPTIC TRANSCEIVER MODULE

10KM 1310NM, DM

Info
title Note
These numbers are taken from Vendor Datasheets as well as IEEE 802.3ae for the 10G parts.

 

Parts and Tools Required

Tooltip
tip ESD protective device

The following items are needed to install/replace a SFP/SFP+ device:

• Electrostatic discharge (ESD) strap
• Replacement SFP/SFP+ transceivers.

Include Page
ESD_wriststrap_7K ESD_wriststrap_7K

Replacing the SFP/SFP+

To replace the SFP/SFP+:

1. Attach an Electrostatic Discharge wrist strap by using the ESD grounding point on the back panel of the chassis. Follow the instructions in the section Connecting Electrostatic Discharge Wrist Strap on SBC 7000.
2. Disconnect the fiber optic and/or Cat 5 cables, as appropriate, from media ports (Media 0-4) and HA ports (HA 0-1).

3. Disengage the SFP/SFP+ transceiver from

   Spacevars
   0 series2

   . The method used to disengage the SFP/SFP+ transceiver will vary according to the manufacturer. For example, hold the wire latch and move it downwards to the horizontal position and pull it outwards.

4. Insert the Sonus-approved SFP/SFP+ transceiver into the desired socket and ensure that the latch mechanism engages.

5. Reconnect the fiber optic and/or Cat 5 cables, as appropriate, to media and HA ports.
6. Verify LEDs above the part are flashing indicating link status and data activity.

7. Verify port functionality by using the application.

CRU Storage

Tooltip
tip ESD protective device

All 

Spacevars
0 series2

CRUs are shipped in electrostatic discharge bags and should be handled using appropriate ESD precautions.

The storage environment for these CRUs are:

• Humidity must be less than 95% (non-condensing).
• Temperature must be between -40C and +70C.

 

Include Page
ESD_footnote ESD_footnote

Pagebreak