Versions Compared

Old Version 2

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH2UserResourceIdentifier{userKey=8a00a0c86820e56901685f374974002d, userName='null'}
AUTH1UserResourceIdentifier{userKey=8a00a0c86e9b2550016ec54396b5000a, userName='null'}
JIRAIDAUTHSBX-112200117394
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c9b802fd8a00a02355cd1c2f0155cd26cb1f0553, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c9b802fd8a00a02355cd1c2f0155cd26cb1f0553, userName='null'}


Panel

In this section:

Table of Contents


Use the SIP JJ9030 Interworking profile to configure parameters needed for SIP JJ9030 Interworking. For information on other related profiles for SIP-ISUP and interworking between different SIP flavors, refer to Support for SIP-ISUP.

Command Syntax

To configure the signaling profile sipJJ9030InterworkingProfile, use the following syntax:

Code Block
% set profiles signaling
	sipJJ9030InterworkingProfile <profile name 1-23 characters>
		addUserEqualPhoneforDivHiInterworking <disabled | enabled>
		bciCalledPartyCategory <noIndication | ordinary | payphone | spare>
		bciChargeIndicator <charge | noCharge | noIndication | spare>
		bciTerminatingIsdnAccess <isdn | nonIsdn>
		chargeAreaInformation <5 digits [0-9]>
		origIoi <1-128 characters>
		originatingCarrierCode <4 digits [0-9]>
		setHiPresentationRestricted <disabled | enabled>
		sipFlavor
			JJ9030
			SIP-T
			SIP-ttc-charging-params
			X-Header
        terminatingCarrierCode <4 digits [0-9]>		
        termIoi <1-128 characters>
		transitIcidInInvite <disabled | enabled>
		transitPcv <disabled | enabled>

Command Parameters

The parameter descriptions for profiles signaling sipJJ9030InterworkingProfile are as follows:

Div
classpdf8pttext
Caption
0Table
1Parameter Description - sipJJ9030InterworkingProfile

Multiexcerpt
MultiExcerptNamePrivate Header for ISDN 64K Unrestricted

Available_since
TypeAvailable Since
Release10.1.2

Private Header for ISDN 64K Unrestricted 

The SBC supports the ISUP signal transfer using the Japanese unique private header "P-N-ISUP-R" between the NNI-GWs. The private header "P-N-ISUP-R" carries the ISUP message-specific information in the SIP message. "P-N-ISUP-R" is required for 64K unrestricted and voice calls. The SBC converts P-N-ISUP-R header contents to ISUP parameters in the SIP-T MIME. Additionally, the SBC creates P-N-ISUP-R header based on the ISUP parameter received in the SIP-T MIME. The SBC uses the following configuration for SIP-T to SIP (JJ-90.30) calls during interworking with the P-N-ISUP-R header.

The SBC adds the parameter pnisuprHeaderInterworking inside the SIP-JJ-90-30 Interworking profile. This parameter is used only if sipFlavor is JJ9030".

The SBC adds the parameter siptOriginatingCarrierCodesForPniusprIwk inside the SIP-JJ-90-30 Interworking profile to configure multiple originating carrier codes.

  • "Originating Carrier Code" is 4 digits.
  • Maximum number of originating carrier codes are 50.
  • This configuration is available only if the sipFlavor is SIP-T.

Note: This configuration mentions all of the supported originating carriers on the SIP-T side.

The list of ISUP parameters and messages supported in the P-N-ISUP-R header are shown below.

Message Type/ISUP Parameter

ISUP Message

IAM

ACM

CPG

ANM

REL

Message Type (0x00)

M

M

M

M

M

Forward Call Indicators (0x07)

M

-

-

-

-

Transmission Medium Requirement (0x02)

M

-

-

-

-

Event Information (0x24)

-

-

M

-

-

Backward Call Indicators (0x11)

-

M

O

O

－

Cause Indicators (0x12)

-

O

O

-

V

User Service Information (0x1d)

O

-

-

-

-

Access Transport (0x03)

O

O

O

O

-

Optional Backward Call Indicators (0x29)

-

O

O

O

-

User-to-User Indicator (0x2A)

-

O

O

-

-

M= Mandatory

O= Optional

V= Mandatory variable



Multiexcerpt
MultiExcerptNameUUI interworking - SIP-T and SIP
Available_since
TypeAvailable Since
Release10.1.3


User to User Information (UUI) interworking between ISUP MIME (SIP-T) and SIP

The interworking between UUI parameter and User-to-User header is categorized in the following two ways:

  • Interwork of User-to-User Information (UUI) of ISUP MIME (SIP-T) to/from "User-to-User" header of the SIP message.
  • Interwork of User-to-User Indicators (UUIN) of ISUP MIME (SIP-T) to/from "P-N-ISUP-R" header of the SIP message.

If the terminating carrier does not use User-User Information, interworking between UUI parameter and User-to-User header is not performed.

Interworking of User-to-User Indicator (0x2A)

The SBC decodes/encodes the User-to-User Indicator (0x2A) parameter in P-N-ISUP-R header for the ACM message and CPG message. UUI interworking is  controlled by userToUserHdrSupport flag on the SIP trunk group.


Command Syntax

To configure the signaling profile sipJJ9030InterworkingProfile, use the following syntax

ParameterLength/RangeDescriptionsipJJ9030InterworkingProfile

1-23 characters

<profile_name> - The name of the SIP JJ-90.30 Interworking Profile.

NOTE: The SBC allows configuring a maximum of 32 sipJJ9030InterworkingProfile(s).

addUserEqualPhoneforDivHiInterworkingN/A

Enable this parameter to add "user=phone" and the "mp" parameter for diversionHistoryInfoInterworking.

  • disabled (default)
  • enabled

For more information on diversionHistoryInfoInterworking, refer to Egress IP Attributes - SIP - CLI.

bciCalledPartyCategoryN/A

The Backwards Call Indicators Called Party Category.

  • noIndication
  • ordinary
  • payphone
  • spare

NOTE: This parameter is mandatory when the parameter sipFlavor is set to SIP-ttc-charging-params.

bciChargeIndicatorN/A

The Backwards Call Indicators Charge Indicator.

  • charge
  • noCharge
  • noIndication
  • spare

NOTE: This parameter is mandatory when the parameter sipFlavor is set to SIP-ttc-charging-params.

bciTerminatingIsdnAccessN/A

The Backwards Call Indicators Terminating ISDN Access Indicator.

  • isdn
  • noIsdn

NOTE: This parameter is mandatory when the parameter sipFlavor is set to SIP-ttc-charging-params.

chargeAreaInformation5 digits (0-9)The Charge Area Information, consisting of 5 digits (0-9).origIoi1-128 charactersThe name of Originating Inter Operator Identifier.originatingCarrierCode4 digits (0-9)

The Originating Carrier Code, consisting of 4 digits (0-9).

Note: This parameter is mandatory when the parameter sipFlavor is set to JJ9030.

setHiPresentationRestrictedN/A

Set Presentation Indicator as "restricted" for historyInfoInterworking.

  • disabled (default)
  • enabled

For more information on historyInfoInterworking, refer to NNI Profile - CLI.

sipFlavorN/A

The type of SIP parameters and procedures used for this interworking profile.

  • JJ9030
  • SIP-T
  • SIP-ttc-charging-params
  • X-Header
terminatingCarrierCode4 digits (0-9)

The Terminating Carrier Code, consisting of 4 digits (0-9).

termIoi1-128 charactersThe name of the Terminating Inter Operator Identifier.transitIcidInInviteN/A

When enabled, the SBC transits the icid-value in P-Charging-Vector transparently in the INVITE sent on the current trunk for JJ90.30 to JJ90.30 calls.

  • disabled (default)
  • enabled

Note:

transitPcv
N/A

When enabled, the SBC transits icid-value, orig-ioi and term-ioi of P-Charging-Vector transparently in JJ90.30 to JJ90.30 calls, using the current trunk group.

  • disabled (default)
  • enabled

Note:

Command Examples

Info
titleNote

The SBC allows configuring a maximum of 32 sipJJ9030InterworkingProfile(s).

To configure sipJJ9030InterworkingProfile with the parameter sipFlavor set to JJ9030, refer to the example below:

Code Block
% set profiles signaling sipJJ9030InterworkingProfile test_sip_JJ9030 sipFlavor JJ9030 origIoi test_origIoi termIoi test_termIoi originatingCarrierCode 9999 chargeAreaInformation 56789
% commit
Info
titleNote

The parameter originatingCarrierCode is mandatory only when you set sipFlavor to JJ9030. For other values of the parameter sipFlavor, configuration of originatingCarrierCode is optional.

To configure sipJJ9030InterworkingProfile with the parameter sipFlavor set to SIP-T, refer to the example below:

Code Block
% set profiles signaling sipJJ9030InterworkingProfile test_2_sip_JJ9030 sipFlavor SIP-T origIoi test_origIoi termIoi test_termIoi chargeAreaInformation 98765
% commit

To configure sipJJ9030InterworkingProfile with the parameter sipFlavor set to SIP-ttc-charging-params, refer to the example below:

Code Block
% set profiles signaling sipJJ9030InterworkingProfile test_3_sip_JJ9030 sipFlavor SIP-ttc-charging-params origIoi test_origIoi termIoi test_termIoi chargeAreaInformation 45679 bciCalledPartyCategory payphone bciChargeIndicator noCharge bciTerminatingIsdnAccess isdn
% commit
Info
titleNote

The following parameters are mandatory only when you set sipFlavor to SIP-ttc-charging-params:

  • bciCalledPartyCategory
  • bciChargeIndicator
  • bciTerminatingIsdnAccess

For other values of the parameter sipFlavor, these parameters are optional.

To configure sipJJ9030InterworkingProfile with the parameter sipFlavor set to X-Header, refer to the example below:

Code Block
languagenone
set profiles signaling sipJJ9030InterworkingProfile test_sip_JJ9030 sipFlavor X-Header origIoi test_origIoi termIoi test_termIoi originatingCarrierCode 9999 chargeAreaInformation 56789 
commit

To display the configured sipJJ9030InterworkingProfile, refer to the example below:


	sipJJ9030InterworkingProfile <profile name 1-23 characters>
		addUserEqualPhoneforDivHiInterworking <disabled | enabled>
		bciCalledPartyCategory <noIndication | ordinary | payphone | spare>
		bciChargeIndicator <charge | noCharge | noIndication | spare>
		bciTerminatingIsdnAccess <isdn | nonIsdn>
		chargeAreaInformation <5 digits [0-9]>
		origIoi <1-128 characters>
		originatingCarrierCode <4 digits [0-9]>
    	pnisuprHeaderInterworking <disabled | enabled>
		setHiPresentationRestricted <disabled | enabled>
		sipFlavor
			JJ9030
			SIP-T
			SIP-ttc-charging-params
			X-Header         
		siptOriginatingCarrierCodesForPnisuprIwk <list of 4-digit carrier codes>
		terminatingCarrierCode <4 digits [0-9]>		
        termIoi <1-128 characters>
		transitIcidInInvite <disabled | enabled>
		transitPcv <disabled | enabled>

Command Parameters

The parameter descriptions for profiles signaling sipJJ9030InterworkingProfile are as follows:

Table 1: Parameter Description - sipJJ9030InterworkingProfile

ParameterLength/RangeDescription
sipJJ9030InterworkingProfile

1-23 characters

<profile_name> - The name of the SIP JJ-90.30 Interworking Profile.

NOTE: The SBC allows configuring a maximum of 32 sipJJ9030InterworkingProfile(s).

addUserEqualPhoneforDivHiInterworkingN/A

Enable this parameter to add "user=phone" and the "mp" parameter for diversionHistoryInfoInterworking.

  • disabled (default)
  • enabled

For more information on diversionHistoryInfoInterworking, refer to Egress IP Attributes - SIP - CLI.

bciCalledPartyCategoryN/A

The Backwards Call Indicators Called Party Category.

  • noIndication
  • ordinary
  • payphone
  • spare

NOTE: This parameter is mandatory when the parameter sipFlavor is set to SIP-ttc-charging-params.

bciChargeIndicatorN/A

The Backwards Call Indicators Charge Indicator.

  • charge
  • noCharge
  • noIndication
  • spare

NOTE: This parameter is mandatory when the parameter sipFlavor is set to SIP-ttc-charging-params.

bciTerminatingIsdnAccessN/A

The Backwards Call Indicators Terminating ISDN Access Indicator.

  • isdn
  • noIsdn

NOTE: This parameter is mandatory when the parameter sipFlavor is set to SIP-ttc-charging-params.

chargeAreaInformation5 digits (0-9)The Charge Area Information, consisting of 5 digits (0-9).
origIoi1-128 charactersThe name of Originating Inter Operator Identifier.
originatingCarrierCode4 digits (0-9)

The Originating Carrier Code, consisting of 4 digits (0-9).

Note: This parameter is mandatory when the parameter sipFlavor is set to JJ9030.

pnisuprHeaderInterworkingN/A

Enable this flag on SIP JJ9030 leg to support P-N-ISUP-R header interworking in SIP-T to SIP JJ90.30 and SIP JJ90.30 to SIP-T calls.

  • disabled (default)
  • enabled

Available_since
TypeAvailable Since
Release10.1.2

setHiPresentationRestrictedN/A

Set Presentation Indicator as "restricted" for historyInfoInterworking.

  • disabled (default)
  • enabled

For more information on historyInfoInterworking, refer to NNI Profile - CLI.

sipFlavorN/A

The type of SIP parameters and procedures used for this interworking profile.

  • JJ9030
  • SIP-T
  • SIP-ttc-charging-params
  • X-Header
siptOriginatingCarrierCodesForPnisuprIwkA list of 4-digit carrier codes,
up to 50 elements

List of supported originating carrier codes on the SIP-T leg for the P-N-ISUP-R header interworking in a SIP-T to SIP JJ9030 call.

Available_since
TypeAvailable Since
Release10.1.2

terminatingCarrierCode4 digits (0-9)

The Terminating Carrier Code, consisting of 4 digits (0-9).

termIoi1-128 charactersThe name of the Terminating Inter Operator Identifier.
transitIcidInInviteN/A

When enabled, the SBC transits the icid-value in P-Charging-Vector transparently in the INVITE sent on the current trunk for JJ90.30 to JJ90.30 calls.

  • disabled (default)
  • enabled

Note:

transitPcv
N/A

When enabled, the SBC transits icid-value, orig-ioi and term-ioi of P-Charging-Vector transparently in JJ90.30 to JJ90.30 calls, using the current trunk group.

  • disabled (default)
  • enabled

Note:


Command Examples

Info
titleNote

The SBC allows configuring a maximum of 32 sipJJ9030InterworkingProfile(s).


To configure sipJJ9030InterworkingProfile with the parameter sipFlavor set to JJ9030, refer to the example below:

Code Block
% set profiles signaling sipJJ9030InterworkingProfile test_sip_JJ9030 sipFlavor JJ9030 origIoi test_origIoi termIoi test_termIoi originatingCarrierCode 9999 chargeAreaInformation 56789
% commit


Info
titleNote

The parameter originatingCarrierCode is mandatory only when you set sipFlavor to JJ9030. For other values of the parameter sipFlavor, configuration of originatingCarrierCode is optional.


To configure sipJJ9030InterworkingProfile with the parameter sipFlavor set to SIP-T, refer to the example below:

Code Block
% set profiles signaling sipJJ9030InterworkingProfile test_2_sip_JJ9030 sipFlavor SIP-T origIoi test_origIoi termIoi test_termIoi chargeAreaInformation 98765
% commit


To configure sipJJ9030InterworkingProfile with the parameter sipFlavor set to SIP-ttc-charging-params, refer to the example below:

Code Block
% set profiles signaling sipJJ9030InterworkingProfile test_3_sip_JJ9030 sipFlavor SIP-ttc-charging-params origIoi test_origIoi termIoi test_termIoi chargeAreaInformation 45679 bciCalledPartyCategory payphone bciChargeIndicator noCharge bciTerminatingIsdnAccess isdn
% commit


Info
titleNote

The following parameters are mandatory only when you set sipFlavor to SIP-ttc-charging-params:

  • bciCalledPartyCategory
  • bciChargeIndicator
  • bciTerminatingIsdnAccess

For other values of the parameter sipFlavor, these parameters are optional.

To configure sipJJ9030InterworkingProfile with the parameter sipFlavor set to X-Header, refer to the example below:

Code Block
languagenone
set profiles signaling sipJJ9030InterworkingProfile test_sip_JJ9030 sipFlavor X-Header origIoi test_origIoi termIoi test_termIoi originatingCarrierCode 9999 chargeAreaInformation 56789 
commit

To display the configured sipJJ9030InterworkingProfile, refer to the example below:

Code Block
> show table profiles signaling sipJJ9030InterworkingProfile
Code Block
> show table profiles signaling sipJJ9030InterworkingProfile
                                                                                                             ADD USER
                                                                                                             EQUAL                                  BCI
                                                                        ORIGINATING TERMINATING              PHONEFOR DIV  SET HI        BCI        CALLED    BCI
                                                                        CARRIER     CARRIER     CHARGE AREA  HI            PRESENTATION  CHARGE     PARTY     TERMINATING
NAME               SIP FLAVOR               ORIG IOI      TERM IOI      CODE        CODE        INFORMATION  INTERWORKING  RESTRICTED    INDICATOR  CATEGORY  ISDN ACCESS
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
test_2_sip_JJ9030  SIP-T                    test_origIoi  test_termIoi  -            -          98765        disabled      disabled      -          -         -
test_3_sip_JJ9030  SIP-ttc-charging-params  test_origIoi  test_termIoi  -            -          45679        disabled      disabled      noCharge   payphone  isdn
test_sip_JJ9030    JJ9030                   test_origIoi  test_termIoi  9999       ADD USER
 -          56789        disabled      disabled      -          -         -
To attach the configured sipJJ9030InterworkingProfile with a sipTrunkGroup
                                                                              EQUAL                                  BCI
                                                                        ORIGINATING TERMINATING              PHONEFOR DIV  SET HI        BCI        CALLED    BCI
                                                                        CARRIER     CARRIER     CHARGE AREA  HI            PRESENTATION  CHARGE     PARTY     TERMINATING
NAME               SIP FLAVOR               ORIG IOI      TERM IOI      CODE        CODE        INFORMATION  INTERWORKING  RESTRICTED    INDICATOR  CATEGORY  ISDN ACCESS
-----------------------------------------------------------------------------------------------------------------------------------------------------------------------------
test_2_sip_JJ9030  SIP-T                    test_origIoi  test_termIoi  -            -          98765        disabled      disabled      -          -         -
test_3_sip_JJ9030  SIP-ttc-charging-params  test_origIoi  test_termIoi  -            -          45679        disabled      disabled      noCharge   payphone  isdn
test_sip_JJ9030    JJ9030                   test_origIoi  test_termIoi  9999         -          56789        disabled      disabled      -          -         -


To attach the configured sipJJ9030InterworkingProfile with a sipTrunkGroup, refer to the example below:

Code Block
% set addressContext default zone defaultSigZone sipTrunkGroup test_sip signaling sipJJ9030InterworkingProfile test_sip_jj9030
% commit


To delete the configured sipJJ9030InterworkingProfile, refer to the example below:

Tip
titleTip

If the sipJJ9030InterworkingProfile is attached to a sipTrunkGroup, detach the profile before you attempt to delete it. To detach, use the following syntax:

% delete addressContext <address_context> zone <zone> sipTrunkGroup <sip_tg> signaling sipJJ9030InterworkingProfile

Commit the command to complete the process of deletion.


Code Block
% delete profiles signaling sipJJ9030InterworkingProfile test_sip_jj9030
% delete profiles signaling sipJJ9030InterworkingProfile test_2_sip_jj9030
% delete profiles signaling sipJJ9030InterworkingProfile test_3_sip_jj9030
% commit

To attach a configured SIP JJ9030 Interworking Profile with a SIP Trunk Group, refer to the example below:

Code Block
% set addressContext default zone defaultSigZone sipTrunkGroup test_sip signaling sipJJ9030InterworkingProfile test_sip_jj9030
% commit

To

delete the configured sipJJ9030InterworkingProfile

detach an attached SIP JJ9030 Interworking Profile from a SIP Trunk Group, refer to the example below:

Tip
titleTip

If the sipJJ9030InterworkingProfile is attached to a sipTrunkGroup, detach the profile before you attempt to delete it. To detach, use the following syntax:

% delete addressContext <address_context> zone <zone> sipTrunkGroup <sip_tg> signaling sipJJ9030InterworkingProfile

Commit the command to complete the process of deletion.

Code Block
delete addressContext default zone defaultSigZone sipTrunkGroup test_sip signaling sipJJ9030InterworkingProfile
commit


Code Block
set profiles signaling sipJJ9030InterworkingProfile jj9030 pnisuprHeaderInterworking enabled
show profiles signaling sipJJ9030InterworkingProfile jj9030
sipFlavor JJ9030;
pnisuprHeaderInterworking enabled;
commit


Code Block
set
Code Block
% delete profiles signaling sipJJ9030InterworkingProfile test_sip_jj9030
% delete  sipt siptOriginatingCarrierCodesForPnisuprIwk [ 1234 1235 1236 1237 1238 1239 ]
show profiles signaling sipJJ9030InterworkingProfile test_2_sip_jj9030
% delete profiles signaling sipJJ9030InterworkingProfile test_3_sip_jj9030
% sipt
sipFlavor SIP-T;
siptOriginatingCarrierCodesForPnisuprIwk [ 1234 1235 1236 1237 1238 1239 ];
commit


Anchor
Use Cases for Transit Pcv and Transit Icid In Invite
Use Cases for Transit Pcv and Transit Icid In Invite
Use Cases for Transit Pcv and Transit Icid In Invite

When using the JJ90.30 standard to improve interconnectivity between IMS networks within Japan, the SBC Core may need to transit some or all of the P-Charging-Vector parameters: icid-value, orig-ioi, and term-ioi. To support this functionality, the SBC includes the configurable signaling parameters, transitPcv and transitIcidInInvite,in the SIP JJ90.30 Interworking profile.

The following diagrams illustrate some sample use cases of the configuration options:

Caption0

Figure

1

: Call from SIP to JJ90.30 (IN) to JJ99.30

Image Removed

caption

Image Added

0Figure1

Figure 2: Call from JJ90.30 to SIP

Image Removed

caption

Image Added

0Figure1

Figure 3: Call from JJ90.30 to JJ90.30

Image Removed

pagebreak

Image Added