Versions Compared

Old Version 2

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH2UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb41059c, userName='null'}
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca7f046c, userName='null'}
JIRAIDAUTHSBX-88903
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c8c30172, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c8c30172, userName='null'}

Noprint
Panel
borderColorgreen
bgColortransparent
borderWidth2

Back to Table of Contents

Back to CLI Configure Mode

Back to Profiles - CLI

...

Panel

In this section:

Table of Contents
maxLevel2

...

Info
iconfalse

Related articles:

 

Use this profile to configure a Call Admission Control (CAC) profile providing the ability for each SIP registered or static endpoint to have individualized limits on the number of active calls, bandwidth size, call rates, over-subscription amounts, burst sizes, etc.

Info
titleNote

To calculate fill rate and bucket size,

...

refer to Token Bucket Policers

...

.

 

SIP CAC Profile

Command Syntax

...

Code Block

...

languagenone

...

% set profiles sipCacProfile <profile_name>

...


	aggregateMessage
	bandwidthLimit

...


	bandwidthLimitThreshold

...


	bandwidthVideoThreshold
	callEgressAggregateEmergencyPreference

...


	callEgressAggregatePreference

...


	callEgressBurstSize

...


	callEgressEmergencyPreference

...


	callEgressRate

...


	callEgressRatePeriod

...


	callIngressAggregateEmergencyPreference

...


	callIngressAggregatePreference

...


	callIngressBurstSize

...


	callIngressEmergencyPreference

...


	callIngressRate

...


	callIngressRatePeriod

...


	callLimit
	callLimitEgress

...


	callLimitIngress

...


	callLimitThreshold

...


	dblAggregateRej
	emergencyOversubscription

...


	emergencyOversubscriptionEgress
	emergencyOversubscriptionIngress

...


	extendedEmergencyIpLimit

...


	extendedEmergencyIpLimitEgress

...


	extendedEmergencyIpLimitIngress

...

...

Optional parameters:

...

languagenone

...

hpcCallLimits
	message
	notify
	options
	otherRequests
	qoe
	refer
	response
	state
	subscribe

 

Command Parameters

Caption
0Table
1SIP CAC Profile Parameter
3SIP CAC Profile Parameter

Parameter

Length/Range

Description

sipCacProfile

1-23

<profile name> – The name of SIP Call Admission Control (CAC) profile.

Refer to the subsequent sections for SIP CAC Profile configuration options.

 

Aggregate Message

 

Use this object to configure the Aggregate Message policer settings listed below.

Command Syntax

Code Block
% set profiles sipCacProfile <profile_name> aggregateMessage 
	egressBurstSize (1-10000)
	egressRate (1-1000, unlimited)

...

...

egressRatePeriod (1-10)

...

...

ingressBurstSize

...

(1-

...

10000)

...

...

ingressRate (1-1000, unlimited)

...

...

ingressRatePeriod (1-10)

...

 
Command Parameters
 Caption
0Table
1Aggregate Message Parameters
3Aggregate Message Parameters
Parameter
Length/Range
Description
egressBurstSize1-10000
Maximum Aggregate Message egress burst size. (default = 10)
egressRate1-1000, 'unlimited'
Maximum Aggregate Message egress rate. (default is 'unlimited')
egressRatePeriod 1-10
Aggregate Message egress rate period in seconds. (default = 1)
ingressBurstSize1-10000
Maximum Aggregate Message ingress burst size. (default = 10)
ingressRate1-1000, 'unlimited'
Maximum Aggregate Message ingress rate. (default is 'unlimited')
ingressRatePeriod
1-10
Aggregate Message ingress rate period in seconds. (default = 1)
Bandwith
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> 
	bandwidthLimit <0-2147483647> 
	bandwidthLimitThreshold <0-100>
    bandwidthVideoThreshold <0-100>
Command Parameters
 Caption
0Table
1Bandwith Parameters
3Bandwith Parameters
Parameter
Length/Range
Description
bandwidthLimit
0-2147483647
Maximum bandwidth (in Kbps) a peer can utilize. (default is 'unlimited')
bandwidthLimitThreshold
0-100
Enter threshold value (as a percentage) to specify bandwidth utilization notification threshold. (default = 0)
bandwidthVideoThreshold
0-100
Enter threshold value (as a percentage of video bandwidth) to limit video streams to a specific bandwidth to prevent video calls consuming call bandwidth otherwise needed for audio calls. (default = 0)
Call
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> 
	callEgressAggregateEmergencyPreference <1-10>
	callEgressAggregatePreference <1-10> 
	callEgressBurstSize <1-500> 
	callEgressEmergencyPreference <disabled | enabled> 
	callEgressRate <1-500, unlimited> 
	callEgressRatePeriod <1-10> 
	callIngressAggregateEmergencyPreference <1-10> 
	callIngressAggregatePreference <1-10> 
	callIngressBurstSize <1-500> 
	callIngressEmergencyPreference <disabled | enabled> 
	callIngressRate <1-500, unlimited> 
	callIngressRatePeriod <1-10> callLimit <0-30000, unlimited> 
	callLimitEgress <0-30000, unlimited> 
	callLimitIngress <0-30000, unlimited>
	callLimitThreshold <0-100> 
Command Parameters
 Caption
0Table
1Call Parameters
3Call Parameters
Parameter
Length/Range
Description
callEgressAggregateEmergencyPreference
1-10
Emergency call preference within the aggregate policer at Egress. (default = 10)
callEgressAggregatePreference
1-10
Call preference within the aggregate policer at Egress. (default = 1)
callEgressBurstSize
1-500
Maximum call burst size for calls to a registered endpoint or peer. (default = 1).
callEgressEmergencyPreference
N/A
Emergency call preference at Egress.
  • disabled (default)
  • enabled
callEgressRate
1-500, unlimited
Maximum egress call rate in calls per time period. (default is 'unlimited').
callEgressRatePeriod
1-10
Time period (in seconds) over which the egress call rate applies. (default = 1).
callIngressAggregateEmergencyPreference
1-10
Emergency call preference within the aggregate policer at Ingress. (default = 10)
callIngressAggregatePreference
1-10
Call preference within the aggregate policer at Ingress. (default = 1)
callIngressBurstSize
1-500
Maximum call burst size from a peer or registered endpoint. (default = 1).
callIngressEmergencyPreference
N/A
Emergency call preference at Ingress.
  • disabled (default)
  • enabled
callIngressRate
1-500, unlimited
Maximum call arrival rate from a peer or registered endpoint per callIngressRatePeriod. (default is 'unlimited'). 
 A value of "0" indicates that call rate policing is not applicable.
callIngressRatePeriod
1-10
Time period (in seconds) over which the callIngressRate applies. (default = 1).
callLimit
0-30000, unlimited
Maximum number of active calls to and from any registered endpoint or peer (e.g. total number of ingress and egress calls). (default is 'unlimited')
callLimitEgress
0-30000, unlimited
Maximum number of outbound active calls. (default is 'unlimited')
callLimitIngress
0-30000, unlimited
Maximum number of inbound active calls. (default is 'unlimited')
callLimitThreshold
0-100
Call Limit utilization notification threshold, as a percentage. (default = 0).
Dynamic Black List Aggregate Reject
 
Use this object to Dynamically Blacklist (DBL) an endpoint based on the CAC policer reject rate using settings below.
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name>  dblAggregateRej 
	ingressBurstSize (1-10000)
	ingressRate (1-1000, unlimited)
...


...
	ingressRatePeriod (1-10)
...
Command Parameters
The SIP CAC Profile Parameters  are shown below:
 Caption
0Table
1
...
DBL Aggregate Reject Parameters
3DBL Aggregate Reject Parameters
Parameter
Length/Range
Description
...
ingressBurstSize1-
...
The name of SIP Call Admission Control (CAC) profile.
...
Mandatory Parameters:
...
 
...
 
...
bandwidthLimit
...
0-2147483647
...
10000
Maximum DBL Aggregate Reject ingress burst size.(default = 1)
ingressRate1-1000, 'unlimited'
Maximum DBL Aggregate Reject ingress rate.(default is 'unlimited')
...
ingressRatePeriod
...
1-
...
Enter threshold value (as a percentage) to specify bandwidth utilization notification threshold. (range: 0-100 / default = 0)
...
0-100
...
callEgressAggregateEmergencyPreference
...
1-10
...
Emergency call preference within the aggregate policer at Egress. (default = 10)
...
callEgressAggregatePreference
...
1-10
...
Call preference within the aggregate policer at Egress. (default = 1)
...
callEgressBurstSize
...
1-500
...
Maximum call burst size for calls to a registered endpoint or peer. (default = 1).
...
callEgressEmergencyPreference
...
N/A
...
Emergency call preference at Egress.
  • disabled (default) 
  • enabled
...
callEgressRate
...
1-500, unlimited
...
Maximum egress call rate in calls per time period. (default is 'unlimited').
...
callEgressRatePeriod
...
1-10
...
Time period (in seconds) over which the egress call rate applies. (default = 1).
...
callIngressAggregateEmergencyPreference
...
1-10
...
Emergency call preference within the aggregate policer at Ingress. (default = 10)
...
callIngressAggregatePreference
...
1-10
...
Call preference within the aggregate policer at Ingress. (default = 1)
...
callIngressBurstSize
...
1-500
...
Maximum call burst size from a peer or registered endpoint. (default = 1).
...
callIngressEmergencyPreference
...
N/A
...
Emergency call preference at Ingress.
  • disabled (default) 
  • enabled
...
callIngressRate
...
1-500, unlimited
...
Maximum call arrival rate from a peer or registered endpoint per callIngressRatePeriod. (default is 'unlimited'). 
 A value of "0" indicates that call rate policing is not applicable.
...
callIngressRatePeriod
...
1-10
...
Time period (in seconds) over which the callIngressRate applies. (default = 1).
...
callLimit
...
0-30000, unlimited
...
Maximum number of active calls to and from any registered endpoint or peer (e.g. total number of ingress and egress calls). (default is 'unlimited')
...
callLimitEgress
...
0-30000, unlimited
...
Maximum number of outbound active calls. (default is 'unlimited')
...
callLimitIngress
...
0-30000, unlimited
...
Maximum number of inbound active calls. (default is 'unlimited')
...
callLimitThreshold
...
0-100
...
Call Limit utilization notification threshold, as a percentage. (default = 0).
...
emergencyOversubscription
...
0-1000
...
Oversubscription of calls (as a percentage) allowed for emergency calls. (default = 0).
...
emergencyOversubscriptionEgress
...
0-1000
...
Oversubscription of egress calls (as a percentage) allowed for emergency calls. When the baseline limit is reached, normal calls are stopped but emergency calls are allowed up to this additional percentage. (default = 10).
...
emergencyOversubscriptionIngress
...
0-1000
...
Oversubscription of calls (as a percentage) allowed for emergency calls. When the baseline limit is reached, normal calls are stopped but emergency calls are allowed up to this additional percentage. (default = 10).
...
extendedEmergencyIpLimit 
...
0-40000
...
Additional number of emergency calls (expressed as a numeric value) allowed for ingress CAC group if call limit and emergency oversubscription quota are exhausted. (default = 0)
...
state
...
N/A
...
Administrative state of this SIP CAC Profile.
  • disabled (default) 
  • enabled
...
Optional Parameters 
...
aggregateMessage
...
N/A
...
Use this object to configure the Aggregate Message policer settings listed below.
  • egressBurstSize – Maximum Aggregate Message egress burst size. (range: 1-10000 / default = 10)
  • egressRate – Maximum Aggregate Message egress rate. (range: 1-1000, unlimited / default is 'unlimited')
  • egressRatePeriod – Aggregate Message egress rate period in seconds. (range: 1-10 / default = 1)
  • ingressBurstSize – Maximum Aggregate Message ingress burst size. (range: 1-10000 / default = 10)
  • ingressRate – Maximum Aggregate Message ingress rate. (range: 1-1000, unlimited / default is 'unlimited')
  • ingressRatePeriod – Aggregate Message ingress rate period in seconds. (range: 1-10 / default = 1)
...
dblAggregateRej
...
N/A
...
Use this object to Dynamically Blacklist (DBL) an endpoint based on the CAC policer reject rate using settings below.
  • ingressBurstSize – Maximum DBL Aggregate Reject ingress burst size.(range: 1-10000 / default = 1)
  • ingressRate – Maximum DBL Aggregate Reject ingress rate.(range: 1-1000, unlimited / default is 'unlimited')
  • ingressRatePeriod – DBL Aggregate Reject ingress rate period in seconds.(range: 1-10 / default = 1)
...
message
...
N/A
...
Use this object to configure the MESSAGE message in a SIP CAC profile using the settings below.
  • egressAggregatePreference – MESSAGE preference within egress aggregate policer. (range: 1-10 / default = 1)
  • egressBurstSize – Maximum MESSAGE egress burst size. (range: 1-10000 / default = 1)
  • egressRate – Maximum MESSAGE egress rate. (range: 1-1000, unlimited / default is 'unlimited')
  • egressRatePeriod – MESSAGE egress rate period in seconds. (range: 1-10 / default = 1)
  • ingressAggregatePreference – MESSAGE preference within ingress aggregate policer. (range: 1-10 / default = 1)
  • ingressBurstSize – Maximum MESSAGE ingress burst size. (range: 1-10000 / default = 1)
  • ingressRate – Maximum MESSAGE ingress rate. (range: 1-1000, unlimited / default is 'unlimited')
  • ingressRatePeriod – MESSAGE ingress rate period in seconds. (range: 1-10 / default = 1)
...
notify
...
N/A
...
Use this object to configure the NOTIFY message in a SIP CAC profile. (egress and ingress settings are same as 'message' parameter above)
...
options
...
N/A
...
Use this object to configure the OPTIONS message in a SIP CAC profile. (egress and ingress settings are same as 'message' parameter above)
...
otherRequests
...
N/A
...
Use this object to configure the OTHER REQUESTS message in a SIP CAC profile using the settings below.
  • egressAggregatePreference – OTHER REQUESTS preference within egress aggregate policer. (range: 1-10 / default = 1)
  • egressBurstSize – Maximum OTHER REQUESTS egress burst size. (range: 1-10000 / default = 5)
  • egressRate – Maximum OTHER REQUESTS egress rate. (range: 1-1000, unlimited / default is 'unlimited')
  • egressRatePeriod – OTHER REQUESTS egress rate period in seconds. (range: 1-10 / default = 1)
  • ingressAggregatePreference – OTHER REQUESTS preference within ingress aggregate policer. (range: 1-10 / default = 1)
  • ingressBurstSize – Maximum OTHER REQUESTS ingress burst size. (range: 1-10000 / default = 5)
  • ingressRate – Maximum OTHER REQUESTS ingress rate. (range: 1-1000, unlimited / default is 'unlimited')
  • ingressRatePeriod – OTHER REQUESTS ingress rate period in seconds. (range: 1-10 / default = 1)
...
qoe
...
N/A
...
Use this object to configure the Quality of Service-based routing configuration. The following parameters are used to measure signaling quality:
  • asr – Answer Seizure Ratio measurement.
    • asrCriticalLimit – The critical ASR limit below which call admission stops. (range: 0-70% / default = 40)
    • defaultQosAsr – Default ASR value to use when no calls are made for a sampling period. (range: 0-100% / default = 90)
    • majorQosAsrLimit – The major ASR limit. When breached, an INFO log is generated and trunk group stats are incremented one value. (range: 0-90% / default = 70)
  • clu – Call Limit Utilization measurement.
    • cluCriticalLimit – Critical CLU limit (as percentage) below which the trunk group or peer is marked out of service for egress calls. (range: 80-100% / default = 80)
  • minTimeToProceed – Minimum time to wait (in seconds) before call admission resumes after peer/trunk group KPI falls below critical threshold. (range: 60-3600 seconds / default = 60)
  • pgrd – Post Gateway Ringing Delay measurement.
    • defaultPgrdFactor – Default PGRD value when no calls are made for a sampling period. (range: 50-10000 milliseconds / default = 500)
    • pgrdCriticalLimit – Critical PGRD limit above which the trunk group is marked out of service, and not chosen for routing. (range: 50-10000 milliseconds / default = 2000)
  • scru– Sustained Call Rate Utilization measurement.
    • scruCriticalLimit – SCRU KPI critical limit (as percentage) above which the trunk group/peer is not chosen for routing. (range: 80-100% / default = 80)
...
refer
...
N/A
...
Use this object to configure the REFER message in a SIP CAC profile. (egress and ingress settings are same as 'message' parameter above)
...
response
...
N/A
...
Use this object to configure the REFER message in a SIP CAC profile.(egress and ingress settings are same as 'otherRequests' parameter above)
10
DBL Aggregate Reject ingress rate period in seconds.(default = 1)
Emergency Oversubscription
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> 
	emergencyOversubscription <0-1000> 
	emergencyOversubscriptionEgress <0-1000> 
	emergencyOversubscriptionIngress <0-1000>
Command Parameters
 Caption
0Table
1Emergency Oversubscription Parameters
3Emergency Oversubscription Parameters
Parameter
Length/Range
Description
emergencyOversubscription
0-1000
Oversubscription of calls (as a percentage) allowed for emergency calls. (default = 0).
emergencyOversubscriptionEgress
0-1000
Oversubscription of egress calls (as a percentage) allowed for emergency calls. When the baseline limit is reached, normal calls are stopped but emergency calls are allowed up to this additional percentage. (default = 10).
emergencyOversubscriptionIngress
0-1000
Oversubscription of calls (as a percentage) allowed for emergency calls. When the baseline limit is reached, normal calls are stopped but emergency calls are allowed up to this additional percentage. (default = 10).
Extended Emgergency IP Limit
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> 
	extendedEmergencyIpLimit <0-40000>
	extendedEmergencyIpLimitEgress <0-40000>
	extendedEmergencyIpLimitIngress <0-40000>
Command Parameters
 Caption
0Table
1Extended Emgergency IP Limit Parameters
3Extended Emgergency IP Limit Parameters
Parameter
Length/Range
Description
extendedEmergencyIpLimit 
0-40000
Additional number of emergency calls (expressed as a numeric value) allowed if call limit and emergency oversubscription quota are exhausted. (default = 0)
extendedEmergencyIpLimitEgress 0-40000Additional number of emergency calls (expressed as a numeric value) allowed for egress CAC group if call limit and emergency oversubscription quota are exhausted. (default = 0)
extendedEmergencyIpLimitIngress 0-40000
Additional number of emergency calls (expressed as a numeric value) allowed for ingress CAC group if call limit and emergency oversubscription quota are exhausted. (default = 0)
 
HPC Call Limits
 Info
titleNote
Before you provision the HPC call limits, ensure that a sipCacProfile exists and associates with a static IP Peer. Refer to Zone - IP Peer - CLI for configuration details.
Use this object to provision the HPC call limits for the SIP CAC profile.
 Include Page
_GETS_Use_Note
_GETS_Use_Note

Command Syntax
To configure the hpcCallLimits in the sipCacProfile, use the following command syntax:
 Code Block
set profiles sipCacProfile <profile_name> hpcCallLimits
	maxCalls <unlimited | blockAll | 1-1000>
	maxIngressRate <unlimited | 1-2000>
	ingressRateInterval <1-30>
	bucketSize <1-4000> 
Parameter Description
The descriptions of the parameters and flags are as follows:
 Caption
0Table
1hpcCallLimts
ParametersLength/RangeDefaultDescriptionM/O
hpcCallLimitsN/AN/AUse this parameter to provision the HPC call limits for the SIP CAC profile for the trunk group.O
maxCallsN/Aunlimited
Use this parameter to configure the maximum number of simultaneous HPC calls.
  • blockAll
  • unlimited (default)
  • <1-1000>
O
maxIngressRateN/Aunlimited
Use this parameter to configure the maximum rate of ingress HPC calls per interval minute.
  • unlimited (default)
  • <1-2000>
O
ingressRateInterval1-305
Use this parameter to configure the interval (in minutes) for the ingress rate of HPC calls.
O
bucketSize1-400010Use this parameter to limit the rate of received HPC calls.O
Command Example
To configure the hpcCallLimits in the sipCacProfile, use the following command example:
 Code Block
% set profiles sipCacProfile testSipCacProfile hpcCallLimits maxCalls 500 maxIngressRate 50 ingressRateInterval 10 bucketSize 32
% commit
To display the hpcCallLimits in the sipCacProfile, use the following command example:
 Code Block
> show profiles sipCacProfile testSipCacProfile hpcCallLimits
    maxCalls 500;
    maxIngressRate 50;
    ingressRateInterval 10;
    bucketSize 32;
  }
}
 
 
 Hide
Inactivity Timeout For Unregistered Endpoints
Command Syntax
 Code Block
% set profiles sipCacProfile <sipCacProfile name> inactivityTimeoutForUnregisteredEndpoints <1 to 1000000>
 
Command Parameters
 Caption
0Table
1Inactivity Timeout For Unregistered Endpoints Parameters
3Inactivity Timeout For Unregistered Endpoints Parameters
Parameter
Length/Range
Description
inactivityTimeoutForUnregisteredEndpoints
1-1000000
<value> (default = 1000000) – Use this parameter to specify the inactivity timeout period, in minutes, before terminating non-registered endpoints.
Note: The parameter inactivityTimeoutForUnregisteredEndpoints only available for configuration after termConditionForUnregisteredEndpoints is set to "inactivitytimeout".
 
Message
 
Use this object to configure the MESSAGE message in a SIP CAC profile using the settings below.
Command Syntax
 Code Block
% set profiles sipCacProfile <profile_name> message 
	egressAggregatePreference (1-10)
	egressBurstSize (1-10000)
	egressRate (1-1000, unlimited)
	egressRatePeriod (1-10)
	ingressAggregatePreference (1-10)
	ingressBurstSize (1-10000)
	ingressRate (1-1000, unlimited)
	ingressRatePeriod (1-10)
Command Parameters
 Caption
0Table
1MESSAGE Parameters
3MESSAGE Parameters
Parameter
Length/Range
Description
egressAggregatePreference1-10
MESSAGE preference within egress aggregate policer. (default = 1)
egressBurstSize1-10000
Maximum MESSAGE egress burst size. (default = 1)
egressRate1-1000, 'unlimited'
Maximum MESSAGE egress rate. (default is 'unlimited')
egressRatePeriod1-10
MESSAGE egress rate period in seconds. (default = 1)
ingressAggregatePreference1-10
MESSAGE preference within ingress aggregate policer. (default = 1)
ingressBurstSize1-10000
Maximum MESSAGE ingress burst size. (default = 1)
ingressRate1-1000, 'unlimited'
Maximum MESSAGE ingress rate. (default is 'unlimited')
ingressRatePeriod
1-10
MESSAGE ingress rate period in seconds. (default = 1)
Notfiy
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> notify 
	egressAggregatePreference (1-10)
	egressBurstSize (1-10000)
	egressRate (1-1000, unlimited)
	egressRatePeriod (1-10)
	ingressAggregatePreference (1-10)
	ingressBurstSize (1-10000)
	ingressRate (1-1000, unlimited)
	ingressRatePeriod (1-10)
Command Parameters
 Caption
0Table
1NOTIFY Parameters
3NOTIFY Parameters
Parameter
Description
notify
Use this object to configure the NOTIFY message in a SIP CAC profile.
NOTE: Egress and ingress settings are the same as MESSAGE Parameters above. Simply replace MESSAGE with NOTIFY in the descriptions.
Options
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> options
	egressAggregatePreference (1-10)
	egressBurstSize (1-10000)
	egressRate (1-1000, unlimited)
	egressRatePeriod (1-10)
	ingressAggregatePreference (1-10)
	ingressBurstSize (1-10000)
	ingressRate (1-1000, unlimited)
	ingressRatePeriod (1-10)

Command Parameters
 Caption
0Table
1OPTIONS Parameters
3OPTIONS Parameters
Parameter
Description
options
Use this object to configure the OPTIONS message in a SIP CAC profile.
NOTE: Egress and ingress settings are the same as MESSAGE Parameters above. Simply replace MESSAGE with OPTIONS in the descriptions.
 
 
Other Requests
Use this object to configure the OTHER REQUESTS message in a SIP CAC profile.
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> otherRequests
	egressAggregatePreference (1-10)
	egressBurstSize (1-10000)
	egressRate (1-1000, unlimited)
	egressRatePeriod (1-10)
	ingressAggregatePreference (1-10)
	ingressBurstSize (1-10000)
	ingressRate (1-1000, unlimited)
	ingressRatePeriod (1-10)

Command Parameters
 Caption
0Table
1OTHER REQUESTS Parameters
3OTHER REQUESTS Parameters
Parameter
Length/Range
Description
egressAggregatePreference1-10
OTHER REQUESTS preference within egress aggregate policer. (default = 1)
egressBurstSize1-10000
Maximum OTHER REQUESTS egress burst size. (default = 5)
egressRate1-1000, 'unlimited'
Maximum OTHER REQUESTS egress rate. (default is 'unlimited')
egressRatePeriod1-10
OTHER REQUESTS egress rate period in seconds. (default = 1)
ingressAggregatePreference1-10
OTHER REQUESTS preference within ingress aggregate policer. (default = 1)
ingressBurstSize1-10000
Maximum OTHER REQUESTS ingress burst size. (default = 5)
ingressRate1-1000, 'unlimited'
Maximum OTHER REQUESTS ingress rate. (default is 'unlimited')
ingressRatePeriod
1-10
OTHER REQUESTS ingress rate period in seconds. (default = 1)
QOE
Use this object to configure the Quality of Service-based routing configuration. 
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> qoe
	asr
		asrCriticalLimit (0-70)
		defaultQosAsr (0-100)
		majorQosAsrLimit (0-90)
	clu 
		cluCriticalLimit (80-100)   
	minTimeToProceed (60-3600)  
	pgrd 
		defaultPgrdFactor (50-10000)  
		pgrdCriticalLimit (50-10000)  
	scru 
		scruCriticalLimit (80-100)

Command Parameters
 Caption
0Table
1QOE Parameters
3QOE Parameters
Parameter
Length/Range
Description
 asrN/A
Answer Seizure Ratio (ASR) measurement.
  • asrCriticalLimit – The critical ASR limit below which call admission stops. (range: 0-70% / default = 40)
  • defaultQosAsr – Default ASR value to use when no calls are made for a sampling period. (range: 0-100% / default = 90)
  • majorQosAsrLimit – The major ASR limit. When breached, an INFO log is generated and trunk group stats are incremented one value. (range: 0-90% / default = 70)
 clu cluCriticalLimit80-100
<value> – Critical Call Limit Utilization (CLU) limit (as percentage) below which the trunk group or peer is marked out of service for egress calls. (default = 80)
 minTimeToProceed60-3600
Minimum time to wait (in seconds) before call admission resumes after peer/trunk group KPI falls below critical threshold. (default = 60)
 
 pgrdN/A
Post Gateway Ringing Delay measurement.
  • defaultPgrdFactor – Default PGRD value when no calls are made for a sampling period. (range: 50-10000 milliseconds / default = 500)
  • pgrdCriticalLimit – Critical PGRD limit above which the trunk group is marked out of service, and not chosen for routing. (range: 50-10000 milliseconds / default = 2000)
scru scruCriticalLimit
80-100
SCRU) KPI critical limit (as percentage) above which the trunk group/peer is not chosen for routing. (default = 80)
Refer
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> refer 
	egressAggregatePreference (1-10)
	egressBurstSize (1-10000)  
	egressRate (1-1000, unlimited)  
	egressRatePeriod (1-10)  
	ingressAggregatePreference (1-10)   
	ingressBurstSize (1-10000)   
	ingressRate (1-1000, unlimited)   
	ingressRatePeriod (1-10)

Command Parameters
 Caption
0Table
1REFER Parameters
3REFER Parameters
Parameter
Description
refer
Use this object to configure the REFER message in a SIP CAC profile.
NOTE: Egress and ingress settings are the same as MESSAGE Parameters above. Simply replace MESSAGE with REFER in the descriptions.
 
 
Response
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> response 
	egressAggregatePreference (1-10)
	egressBurstSize (1-10000)   
	egressRate (1-1000, unlimited)
	egressRatePeriod (1-10)
	ingressAggregatePreference (1-10)
	ingressBurstSize (1-10000)
	ingressRate (1-1000, unlimited)
	ingressRatePeriod (1-10)
Command Parameters
 Caption
0Table
1RESPONSE Parameters
3RESPONSE Parameters
Parameter
Description
response
Use this object to configure the RESPONSE message in a SIP CAC profile.
NOTE: Egress and ingress settings are the same as OTHER REQUESTS Parameters above. Simply replace OTHER REQUESTS with RESPONSE in the descriptions.
 
 
State
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> state <disabled | enabled>
Command Parameters
 Caption
0Table
1State Parameters
3State Parameters
Parameter
Description
state
Administrative state of this SIP CAC Profile.
  • disabled (default)
  • enabled
NOTE: Setting a SIP CAC profile state to "disabled" does not disable SIP CAC functionality on IP Peers to which the SIP CAC profile is assigned. To disable SIP CAC functionality on a specific IP Peer, disassociate the SIP CAC profile from the IP Peer.
Subscribe
Command Syntax
 Code Block
languagenone
% set profiles sipCacProfile <profile_name> subscribe 
	egressAggregatePreference (1-10)   
	egressBurstSize (1-10000)   
	egressRate (1-1000, unlimited)   
	egressRatePeriod (1-10)
	ingressAggregatePreference (1-10)   
	ingressBurstSize (1-10000)
	ingressRate (1-1000, unlimited)
	ingressRatePeriod (1-10)
Command Parameters
 Caption
0Table
1SUBSCRIBE Parameters
3SUBSCRIBE Parameters
Parameter
Description
subscribe
Use this object to configure the SUBSCRIBE message in a SIP CAC profile.
NOTE: Egress and ingress settings are the same as MESSAGE Parameters above. Simply replace MESSAGE with SUBSCRIBE in the descriptions.
 Hide
Termination Condition For Unregistered Endpoints
Command Syntax
 Code Block
% set profiles sipCacProfile <sipCacProfile name> termConditionForUnregisteredEndpoints <ifneeded | inactivitytimeout | never>
 
Command Parameters
 Caption
0Table
1Term Condition For Unregistered Endpoints Parameters
3Term Condition For Unregistered Endpoints Parameters
Parameter
Description
termConditionForUnregisteredEndpoints
Use this parameter to specify the termination condition for unregistered endpoint CACs.
  • never – An unregistered CAC is only terminated upon receipt of a non-401/407 response for an initial INVITE from the Regsitrar/AS or from executing the cacNonRegEndPointRemoveEntry CLI command.
  • ifneeded – An unregistered CAC is terminated if the maximum number of CACs is reached and there is a need to install a new CAC.
  • inactivitytimeout – An unregistered CAC is terminated after a specified time of inactivity (see inactivityTimeoutForUnregisteredEndpoints.
Note: The parameter inactivityTimeoutForUnregisteredEndpoints only available for configuration after the "inactivitytimeout" option above is selected.
 
Command Examples
...
subscribe
...
N/A
...
Use this object to configure the SUBSCRIBE message in a SIP CAC profile. (egress and ingress settings are same as 'message' parameter above)
 
...
 Code Block
languagenone
 % set profiles sipCacProfile SIPCAC_TEST state enabled 
	callIngressRate 78 callIngressRatePeriod 4 
	callIngressBurstSize 342 callEgressRate 43 
	callEgressRatePeriod 3 callEgressBurstSize 45 callLimit 
	4567 emergencyOversubscription 24
% commit

% show profiles sipCacProfile SIPCAC_TEST 
 	state enabled;  
	callIngressRate 78;  
	callIngressRatePeriod 4;  
	callIngressBurstSize 342;  
	callEgressRate 43;  
	callEgressRatePeriod 3;  
	callEgressBurstSize 45;  
	callLimit 4567;  
	emergencyOversubscription 24;
 Code Block
languagenone
% set profiles sipCacProfile cacProfile1 extendedEmergencyIpLimit 10 extendedEmergencyIpLimitIngress 20 extendedEmergencyIpLimitEgress 30
% commit

% show profiles sipCacProfile cacProfile1 
extendedEmergencyIpLimit        10;
extendedEmergencyIpLimitIngress 20;
extendedEmergencyIpLimitEgress  30;
 
 Pagebreak