| Include Page |
|---|
| Transparency_Profile_Note |
|---|
| Transparency_Profile_Note |
|---|
|
Specifies the name of SIP header to transparently pass.
The flexible header transparency profile supported in earlier release, where transparency for a random header is achieved by adding its name to the profile. The functionality was limited to initial INVITE request, REGISTER request, and mid-dialog requests in an INVITE initiated dialog (excluding a mid-dialog SUBSCRIBE as it is not supported). Selective unknown headers can be passed transparently in REGISTER, initial INVITE, and in mid-dialog requests in an INVITE initiated dialog. Header transparency was not supported for out-of-dialog messages in earlier SBC release.
SBC is now enhancedThe SBC supports the following out-of-dialog functionality:
- To enable transparency for "all" the headers.
- To selectively ignore transparency of headers (useful with "all" transparency).
- To exclude the methods for which transparency of headers is not needed.
| Note |
|---|
|
The transparency profile is associated with the egress trunk group. The header transparency is based on the headers that are present in the transparency profile of the egress trunk group for requests and headers that are present in the ingress trunk group for responses. |
| Note |
|---|
|
PRACK messages and responses to PRACK messages are not sent end-to-end through SBC. Therefore, SBC does not support transparency of message-bodies or headers in these messages. ACK messages are not normally sent end-to-end through SBC. Transparency of ACK messages is not supported even if the endToEndAck flag is enabled in the "IP Signaling Profile". In late media scenarios, the SBC does not support transparency of headers and bodies. Transparency for headers and bodies is not supported for methods such as CANCEL and methods that are "hop-by-hop". |
| Note |
|---|
|
Headers may be configured in compact form and transparently passed using a Transparency Profile. It is advisable to configure both compact and long formats to ensure both types of received headers in the PDU are transparently passed. |
On SBC main screen, go to Configuration > Profile Management > Category: Service Profiles >Transparency Profile > Sip Header.
Select the desired Transparency Profile from the drop-down list to view/edit the Sip Header parameters.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Configuration - Profile Management - Transparency Profile - Sip Header Main Field |
|---|
|
|
The Sip Header window is displayed.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Profile Management - Service Profiles - Sip Header |
|---|
|
|
To edit any of the Sip Header in the list, click the radio button next to the specific Sip Header name.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Profile Management - Service Profiles - Sip Header Highlighted |
|---|
|
|
The Edit Selected Sip Header window is displayed below.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Profile Management - Service Profiles - Sip Header Edit Window |
|---|
|
Image Modified |
Make the required changes and click Save at the right hand bottom of the panel to save the changes made.
To create a new Sip Header, click New Sip Header tab on the Sip Header List panel.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Profile Management - Service Profiles - Sip Header Fields |
|---|
|
|
The Create New Sip Header window is displayed.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Profile Management - Service Profiles - Sip Header Create Window |
|---|
|
Image Modified |
The following fields are displayed:
| Note |
|---|
|
If a specific header is configured, Ignore Transparency and Excluded Methods are exclusive. If Ignore Transparency is configured, Excluded Methods is not displayed later. If Excluded Methods is configured, Ignore Transparency is not displayed. |
| Note |
|---|
|
The Ignore Transparency configurable applies in the following cases: - when combined with a configuration to allow "all" SIP headers
-or- - when one of the transparency flags for SIP header in the IP Signaling Profile is enabled
|
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Transparency Profile - Sip Header Parameters |
|---|
|
Parameter | Description |
|---|
Header Name Name
| Specifies the Header name of this SIP Transparency Profile. The value ranges up to 31 characters. | Excluded Methods | Specifies the method(s) for which the transparency of the SIP header is not applicable. Options are: registerinvitesubscribenotifybyeinfoinvitepublishmessagenotifyreferoptionspublishupdatereferbyeregisterpracksubscribecancelupdate
| Ignore Transparency | If Yes, this parameter excludes the transparency of the SIP header. Options are: |
|
To copy any of the created Sip Header and to make any minor changes, click the radio button next to the specific Sip Header to highlight the row.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Profile Management - Service Profiles - Sip Header Highlighted |
|---|
|
|
Click Copy Sip Header tab on the Sip Header List panel.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Profile Management - Service Profiles - Sip Header Fields |
|---|
|
|
The Copy Selected Sip Header window is displayed along with the field details which can be edited.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Profile Management - Service Profiles - Sip Header Copy Window |
|---|
|
Image Modified |
Make the required changes to the required fields and click Save to save the changes. The copied Sip Header is displayed at the bottom of the original Sip Header in the Sip the Sip Header List panel.
To delete any of the created Sip Header, click the radio button next to the specific Sip Header which you want to delete.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Profile Management - Service Profiles - Sip Header Highlighted |
|---|
|
|
Click Delete at the end of the highlighted row. A delete confirmation message appears seeking your decision.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Profile Management - Service Profiles - Sip Header Delete Confirmation |
|---|
|
|
Click OK Yes to remove the specific Sip Header from the list.