...
...
| borderColor | green |
|---|
| bgColor | transparent |
|---|
| borderWidth | 2 |
|---|
...
Back to Table of Contents
Back to CLI Configure Mode
Back to Address Context - CLI
...
In this section:
...
Static IP Routes for IP Interfaces
The staticRoute object is used to configure static IP routes for the IP interfaces. A static route indicates the nextHop gateway and IP interface that is used for a particular peer network IP prefix.
A route preference may be configured for static routes as shown in the command syntax. The lower the preference value, the more likely the route is to be used.
| Info |
|---|
|
- Static routes using a specific ceName can only be added for packet interfaces.
- The SBC does not allow to delete the
ceName separately. - A static route is deleted only from the instance in which it is configured, and not from both active and standby instances of a HA pair configuration.
- The configuration of a
staticRoute with respect to a ceName cannot be edited. If any change is desired in the configuration, delete the staticRoute and reconfigure it.
|
| Include Page |
|---|
| IP_IGs_ServedBySeperateProcessors |
|---|
| IP_IGs_ServedBySeperateProcessors |
|---|
|
Command Syntax
| Code Block |
|---|
|
% set addressContext <addressContext_name> staticRoute <destinationIpAddress> <ip_prefix_length> <nextHopIPaddress> <ipInterfaceGroupName> <ipInterfaceName>
condition ceName (node name)
preference |
...
<100-2147483647>
% show addressContext <addressContext_name> staticRoute
% delete addressContext <addressContext> staticRoute <IpAddress> |
Command Parameters
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Static Route Parameters |
|---|
|
Parameter | Length/Range | Description |
|---|
addressContext
| 1-23 | <addressContext_name> – The name of the address context. The address context is a container of objects that correspond to a specific IP Addressing domain.
| staticRoute
| N/A |
|
...
<ENUM server Ip Address> – The destination IP address of the ENUM server. The following IP address types are supported:
- IPv4 – This is V4 IP address in dotted decimal form (for example 128.127.50.224).
- IPv6 – This is V6 IP address in hexadecimal/colon form (for example, 1280:1276:3350:2224:2222:3333:8888:1245 or
|
|
...
...
0-128 | The IP prefix length of this static route entry. | <nextHopIPaddress>
| N/A | The IPv4 or IPv6 address of the next system en route to the destination. | <ipInterfaceGroupName>
| N/A | The name of the IP interface group. | <ipInterfaceName>
| N/A | The name of the IP interface for this entry. |
|
...
condition | N/A | For an HA pair configuration (only), use this object to define the routes added to this HA pair.ceName – The name of the computing element that hosts the port used by the IP interface (length: 1-255 characters).
NOTE: The supports only the ceName condition in this release.NOTE: Before configuring the condition with a specific ceName, the ipInterfaceGroupName and ipInterfaceName parameters must first be configured for this Static Route. These three parameters cannot be configured under the same commit command. For further details, refer to IP Interface Group - CLI. NOTE: The condition option is only applicable for non-management interfaces. | preference
| 100-2147483647 | <preferenceNumber> (default = 100) – The route preference value. The management route preference range is 1-99 and the packet route preference range is greater than or equal to 100.
|
|
...
displaylevel
...
1-64
...
To display different levels of output information in show commands.
Command Example
To display static routes:
| Code Block |
|---|
|
% show addressContext default staticRoute
staticRoute 10.6.30.105 32 10.34.26.1 LIF2 lif_eth3 {
preference 10;
}
staticRoute 10.34.9.70 32 10.34.25.1 LIF1 lif_eth2 {
preference 10;
}
staticRoute 10.34.9.95 32 10.34.26.1 LIF2 lif_eth3 {
preference 10;
}
staticRoute 10.34.13.194 32 10.34.25.1 LIF1 lif_eth2 {
preference 1;
}
staticRoute 10.34.13.195 32 10.34.26.1 LIF2 lif_eth3 {
preference 10; |
The staticRoute object is used to configure static IP routes for the management interfaces. A static route indicates the nextHop gateway and management interface that is used for a particular peer network IP prefix.
| Info |
|---|
| For details on Static IP Routes for Management interfaces, |
...