Page History

 

Noprint
Panel borderColor green bgColor transparent borderWidth 2 Back to Table of Contents Back to Installing SBC 5000 and 7000 Series Software Back to Configuring the SBC 5000 Series Platform

Include Page
IPMI_Security_Vulnerability IPMI_Security_Vulnerability

Sonus ships the 

Spacevars
0 series

pre-configured with the default IP address “169.254.77.1” to facilitate out of the box access to the BMC web interface. Configure your PC/Laptop IP address to be on this network so that it can communicate with 

Spacevars
0 series

platform. To access the BMC web application, connect the Field Service Port to the PC configured with the pre-configured IP address and type the IP address in a web browser.

Info
title Info
Refer to Introduction to EMA for a list of supported browsers and operating systems.

To configure BMC for remote access:

1. Connect your PC/laptop via an Ethernet cable to the Field Service Port (FSP) at the back of SBC (Here it is 5210) and power it up (if not already on).

   Caption
   0 Figure 1 Connecting PC to FSP

2. Verify that both link LEDs at the FSP are lit. If only the left LED is lit, your PC/laptop network adapter link speed may be set to 10Mbps. Check the PC/laptop Device Manager, and if necessary set your PC/laptop link speed to 100 Mbps/Full Duplex.
   
   
3. If your PC/laptop uses DHCP and Automatic Private IP Address setting (default setting), the PC/laptop is assigned an IP address in the same subnet as the initial BMC IP; therefore proceed to Step 9. If your PC/laptop does not use DHCP, proceed to the Step 4 to configure a static IP.
   
   

4. In Windows 7 operating system, Open open Control Panel > Network and Sharing Center. The Network and Sharing Center window displays.

   Caption
   0 Figure 1 Network and Sharing Center
   Image Modified

5. Click Local Area Connection link.The Local Area Connection Status screen displays.

   Caption
   0 Figure 1 Local Area Connection Status
   Image Modified

6. Click Properties. The LAN Properties screen displays.

   Caption
   0 Figure 1 Local Area Connection Properties
   Image Modified

7. Select "Internet Protocol Version 4 (TCP/IPv4)" option and click Properties. The Internet Protocol Version 4 (TCP/IPv4) Properties screen appears.

   Caption
   0 Figure 1 IPv4 Properties Screen
   Image Modified

8. Select Use the following IP addresses option and input the IP address, Subnet mask, and Default gateway. Click OK.

   Caption
   0 Figure 1 Configuring IP Address
   Image Modified

9. Anchor
   Step9 Step9

   Type the pre-configured IP address “169.254.77.1” in a web browser (Firefox is the recommended browser. If using Internet Explorer, you must manually add “https://169.254.77.1” as a trusted site), and connect to the BMC web interface.
   
   
   note

   Info
   icon false title Note
   The SBC 5000 is delivered with sample self-signed X.509 certificates. Please be aware that even though these sample certificates will allow you to use HTTPS to access the SBC 5000 from BMC and EMA interfaces, using this protocol with the sample certificates is not a truly secure access method. If your organization requires a more secure access, see Generating PKI Certificates.

10. Login Log on to the SBC 5000 BMC GUI.
    At the prompt, enter:

    Code Block
    language none
    Username: root Password: superuser

    The SBC 5000 BMC main screen is displayed.
    
    

11. Click Configuration tab. The Configuration screen is displayed.

    Caption
    0 Figure 1 Configuration Screen
    Image Removed

    From Options menu, click BMC > Network. The BMC Network Settings screen window is displayed.

    Caption
    0 Figure 1 BMC Network Screen
    Image Modified

    Configure the BMC IP Address, Prefix and Default Gateway network settings. Select the Select Enable JViewer, and/or Enable SSH and Enable IPMI options under Security  options under the “Security” settings depending upon your security requirements.

    Caption
    0 Figure 1 Configuring BMC Network
    Image Removed

    It is recommended to leave the Enable IPMI option disabled.

    note

    Info
    icon false title Note
    Enable IPMI is a service impacting operation. This reboots both the BMC and the host server. The changes to any of the three security items does not occur until the you click Save button is clicked.

12. Click Save.
    The following pop-up messages appearmessage is displayed.

    Caption
    0 Figure 1 Warning Messages
    Image ModifiedImage Removed

13. Click OK in each pop-up message to proceed.

14. Disconnect the PC/Laptop from FSP.

15. Connect the FSP of SBC 5000 to the Ethernet router on LAN segment using a CAT5 Ethernet cable to access the BMC over the network.

    Caption
    0 Figure 1 Field Service Port

16. Connect a PC to the IP network that can access the BMC IP address.
    
    

17. Continue to configure network management interfaces.
    

    note

    Info
    icon false title Note
    Once the real BMC address is configured, you cannot access the pre-configured BMC address. Clear the browser cache (browser-specific) and open a new browser session to reflect the changes.

...

borderColor	green
bgColor	transparent
borderWidth	2

...

1. Pagebreak