Versions Compared

Old Version 2

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
borderColor
Noprint
Panel
green
bgColortransparent
borderWidth2

Back to Table of Contents

Back to Installing SBC 7000 Series Hardware

Back to Rack Mounting the SBC 7000 Chassis

Panel

In this section:

Table of Contents
maxLevel2
minLevel2

 

This section provides information on the 

Spacevars
0series2
package content and required tools to rack mount the
Spacevars
0product
chassis.

Required Tools

Before you install the

Spacevars
0product
chassis into a rack, make sure that you have the following tools and equipment readily available:

  • #2 Phillips screwdriver (to install brackets and the chassis)
  • 7/16" (11 mm) wrench (to attach earth ground lug)
  • Label maker (to label cables, if needed)
  • Voltmeter (for installing units with DC power supplies)
  • A marker or masking tape to mark mounting holes

SBC 7000 Package Content

Unpack and inspect your equipment and hardware to verify you have all the necessary items to install your

Spacevars
0series2
chassis.

 

Excerpt
Warning

Due to the size and weight of the

Spacevars
0series2
chassis, at least two people are required when lifting, mounting or unmounting the chassis.

Accessory Kit

The Bill of Materials (BOMs) for the 

Spacevars
0series2
Accessory Kit is:

Caption
0Table
1BOM Details

Item Number

Item Description

Quantity

501-00526LUG 2 HOLE, #3-#4 AWG, 90° ANGLE TONGUE, 1/4" STUD HOLE, 1/2"-5/8" HOLE SPACING1
401-00119CABLE, 9 POS DSUB M-F NULL, MOULDED-3M.-ROHS1
510-00038
Tooltip
tipESD protection device

ESD WRIST STRAP

1
510-00056WASHER, 1/4 SPLIT LOCK STLS STL-ROHS2
511-00376WASHER, FLAT -1/4 REG STLS STL-ROHS2
511-00046NUT, HEX 1/4-20 STL STEEL-ROHS2
511-00243#6 AWG TERMINAL LUG4
Warning

Do not use fan handles when lifting the chassis.

Note

Carefully remove the contents from the shipping container, and check each item for damage. The

Spacevars
0series2
is shipped with the items listed below. If any item is missing or damaged, contact your Sonus representative for support.

Universal Rack Mount Kit

The fixed mount universal rack mount kit consists of:

ItemQuantity
Fixed Mount Brackets2
Rear Mount Support Brackets2
19" Rear Mount Brackets2
23" Rear Mount Brackets2
10-32 X 5/16" flathead Philips screws to affix fixed mount brackets6
10-32 X 5/16" panhead Philips screws to affix rear mount support brackets10
10-32 X 3/4" truss head Philips screws with washer to affix to rack, if appropriate12
12-24 X 3/4" truss head Philips screws with washer to affix to rack, if appropriate12 
M5 X 3/4" truss head Philips screws with washer to affix to rack, if appropriate12
M6 X 3/4" truss head Philips screws with washer to affix to rack, if appropriate12
10-32 cage nuts to affix to rack, if appropriate12

 The following figure depicts the contents of the Universal Rack Mount Kit contents.

Caption
0Figure
1Universal Rack Mount Kit

Pagebreak