Add_workflow_for_techpubs | ||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
CSS Stylesheet |
---|
img.confluence-embedded-image { display: inline-block !important; } |
Panel | ||||
---|---|---|---|---|
In this section:
|
Panel | |
---|---|
Related Page:
|
Running the SBC SWe Lite initial setup sequence is required for all deployment environments (KVM, VMware ESXi, Microsoft Hyper-V hypervisors and Microsoft Azure).
Info | ||||
---|---|---|---|---|
| ||||
This procedure runs the initial setup on the
You do not need to perform this procedure if you use the cloud-init function. |
The SBC SWe Lite must be installed before running initial setup. Refer to Installing SBC SWe Lite and click on the applicable platform:
If a valid IP address was generated at the end of the installation procedure, the options are:
Proceed to step 4, bypassing the mapping process (before you do this, see the Note below).Proceed to step 3 to Mapping Network Interfaces to review and reconfigure network interfaces (optional).
Note | ||||
---|---|---|---|---|
|
Mapping Network Interfaces is required for the following |
configurations:
|
Note |
---|
This step does not apply to Azure deployments. |
Optional: Bypass the mapping process and proceed to step 2 to launch the browser. This option should be used only if your network setup has been recently reviewed, and does not meet the configurations listed above.
Enter the IP address generated by (generated by SBC SWe Lite at the end of the installation procedure , and then press Enter to launch the
Spacevars | ||
---|---|---|
|
Spacevars | ||
---|---|---|
|
For an on-premises deployment (Microsoft Hyper-V, VMware ESXi, or KVM VMM), the management IP address is displayed in the console after SBC SWe Lite starts.
Configure the System Information, IP address, Local Users and Connectivity Information panes using the appropriate values for your location.
Info |
---|
All fields are defined below for Initial Ribbon SBC SWe Lite Setup For KVM Hypervisor, VMware ESXi, Microsoft Hyper-V. If a field is pre-populated, the current value is Ribbon's recommendation. Any other recommended values are indicated. For Azure. Where applicable, a note indicates whether a field requires any mandatory or recommended values. |
Caption | ||||||
---|---|---|---|---|---|---|
| ||||||
Caption | ||||
---|---|---|---|---|
| ||||
Sets how the SBC acquires the IP address information. Valid entries: Static or Dynamic. Default entry: Static. Static enables you to enter an IP address manually. Dynamic acquires the interface's IP configuration dynamically from a reachable DHCP server. For Azure, Static is the recommended value.
Enter the Host Name for the SBC. This is typically useful when you plan to join useful joining an SBC to a domain. This field is required. Refer to Hostname Conventions for hostname rules.For Azure, verify this field is valid and enter the applicable host name.
Typically useful Useful if the SBC system resides on a network that uses an internet domain name (such as https:// ribboncommunications.com/). This field is displayed only when Static is selected from the Network Configuration field. For Azure, this field is required.
Use this field to set the local time zone of the SBC. For Azure, this field is required.
The default value for this field is No, and none of the following fields are visible. If the value is set to Yes, then the following fields are visible: For Azure, verify if this field is applicable to your network configuration and set the fields appropriately.
Use this list box to select the desired
logging logging level. Valid options: Trace, Debug, Informational, Warning, Error or Fatal.
The IP address of the destination log server or its FQDN. This field is required.
The logging port on the destination log server. This field is required.
Use this list box to select the transport protocol for the logging information. Valid selections: UDP or TCP.
Select a logging facility code to insert in the transmitted log such that the entries can be filtered. For more information see RFC 5424.
Specifies whether the NTP will be used as a time source. Valid entries: Yes (NTP is used as the time source) or No (NTP is not used as the time source).
Default entry: Yes.
NTP Server
Specifies the host name or IP address of the NTP server. If the hostname is supplied, the
Spacevars | ||
---|---|---|
|
Specifies whether authentication is used for communicating with the NTP server. Valid entries: Enabled (Authentication is used with NTP Server) or Disabled (Authentication is not used with NTP Server). For Azure, verify if this field is applicable to your network configuration and set the field appropriately.
Specifies the MD5 Key ID to be used in authenticating the first NTP server. This field is visible only when the NTP Server Authentication field is set to Enabled.
Specifies the MD5 key used when authenticating the first NTP Server.
Determines whether Easy Configuration is launched upon completion of initial configuration. Valid entries: Launch on First Login (Easy Configuration is launched upon login) or Do not Launch (Easy Configuration is not launched upon login). Default entry: Launch on First Login.
For Azure, the default field of Launch on First Login is the recommended value.
Info |
---|
If the 30 day embedded trial license has expired and the SBC SWe Lite instance does not have a production license, the Easy Setup option is not available. For Easy Configuration license guidelines, refer to: Easy Configuration - Notes. |
0 | Figure |
---|---|
1 | Remote Log Configuration - Config Syslog "Yes" |
Note: This field is not applicable to Azure.
Enter the IP address through which the SBC communicates over Ethernet. The IP address in this field will be configured onto the Admin Port. This field is required.
This field is displayed when the Network Configuration field is set to Static.
Note: This field is not applicable to Azure.
The Netmask which will be applied to the Admin IP IPv4 address. This field is required.
This field is displayed when the Network Configuration field is set to Static.
Enables or disables the use of an IP address with Ethernet 1.
If you select Yes:
For KVM Hypervisor, VMware ESXi, Microsoft Hyper-V: the IPv4 Address, Netmask, and Media Next Hop fields are visible. These fields are required if set to Yes.
IPv4For Azure, the default value is recommended.
Note: This field is not applicable to Azure.
Enter the IP address through which the SBC communicates over Ethernet. The IP address in this field will be configured onto Ethernet 1. This field is required if set to Yes.
Note: This field is not applicable to Azure.
The Netmask will be applied to the Ethernet 1 IPv4 address. This field is required if set to Yes.
The Media Next Hop IP specifies the gateway for a particular interface subnet so that all the media traffic egress to that gateway. This field is required if set to Yes.
Note |
---|
For KVM Hypervisor, VMware ESXi, Microsoft Hyper-V: For Ethernet 1 - 4, when the Configure IP field is set to Yes, the corresponding fields for that Ethernet port are required. For Azure: The default of No is recommended. |
Note: This field is not applicable to Azure.
Enables or disables the use of an IP address with Ethernet 2. If you select Yes, the IPv4 Address, Netmask, and Media Next Hop fields are visible. This field is required if set to Yes.
Note: This field is not applicable to Azure.
Enables or disables the use of an IP address with Ethernet 3. If you select Yes, the IPv4 Address, Netmask, and Media Next Hop fields are visible. This field is required if set to Yes.
Note: This field is not applicable to Azure.
Enables or disables the use of an IP address with Ethernet 4. If you select Yes, the IPv4 Address, Netmask, and Media Next Hop fields are visible. These fields are required if set to Yes.
This section is used to create a local Administrative User and an optional REST User.
Enter a Admin user name. This For all configurations, this field is required.
Enter a password for the administrative user. This For all configurations, this field is required.
Re-enter the same password to confirm. This For all configurations, this field is required.
Anchor | ||||
---|---|---|---|---|
|
Note | ||||
---|---|---|---|---|
| ||||
To recover a lost password:
|
Select Yes if you wish to configure and enable a REST user. If you select Yes, you will be required to enter the REST username, enter, and confirm the REST username password. For all configurations, this field is required.
If you plan to use a gateway to route IP traffic from the SBC, set this field to Yes and specify a Default Gateway IP address, which should be in the same subnet as the primary Ethernet port. This field is displayed only when Static is selected from the Network Configuration field.
For Azure, the default entry of No is recommended.
The IP Address of the default gateway. This field is displayed only when Configure Default Route is set to Yes. This field is required if Config Default Route is set to Yes.
If you plan to use host names for routing network traffic from the SBC system, select Yes and provide a Primary Server IP address.
For Azure, the default entry of Yes is recommended.
The IP address of the primary DNS server. This field is required if the Use Primary DNS field was set to Yes.
For Azure, this field is required.
Optionally, set the Use Secondary DNS to Yes and provide a Secondary Server IP address.For Azure, verify if this field is applicable to your network configuration and set the field appropriately.
The Add Static Route Entry configuration enables you to create static routes/gateways for the additional Ethernet interfaces, if required. To create a static route, click the (.
) icon in the Static Subnet IP Routes section. Populate the fields using the definitions below and then click OKFor all configurations, these fields are optional.
Caption | ||||
---|---|---|---|---|
| ||||
Enter the destination IP Address. This field is required.
Enter the network mask of the destination host or subnet.This field is required.
Enter the IP Address of the next-hop router to use for this Static Route. This field is required.
Enter the cost of this route, which indirectly specifies the preference of the route. Lower values indicate more preferred routes. Typical value is 1 for most static routes, which indicates that static routes are preferred to dynamic routes. Valid entry: 1 - 255. This field is required.
After the fields
and thenare populated, click OK to save the Initial
SBC Setup. If you have a console, you will see the admin IP address. Spacevars 0 company
Caption | ||||||
---|---|---|---|---|---|---|
| ||||||
Access the SBC Edge Web UI via Admin IP address or
Use a Web browser to access the
Spacevars | ||
---|---|---|
|
title | Easy Configuration Wizard Unavailable Prior to License Installation |
---|
The Easy Configuration Wizard does not open automatically upon the first login. A valid license must be applied first. In the absence of a license, the SBC SWe Lite displays the following message in the license page. Once a license has been applied, the Easy Configuration Wizard will be available under the Tasks tab.
Select the appropriate license type:
(configured above).
Info | ||||
---|---|---|---|---|
| ||||
For
|
If the Easy Setup field was available during initial setup and configured to Launch on First Login, the Web UI presents the Easy Configuration Wizard upon login. To select the specific scenario in which to provision, refer to Easy Configuration Wizard. Once complete, the
supports calls. Spacevars 0 product3
If the Easy Setup field was not available during initial setup or the field was not set to Launch on First Login, the Web UI opens with an abbreviated Tasks tab presentation.
Caption | ||||
---|---|---|---|---|
| ||||
Spacevars | ||
---|---|---|
|
title | IMPORTANT! |
---|
To select the specific scenario in which to provision, refer to Easy Configuration Wizard. Once complete, the
supports calls. Spacevars 0 product3
Pagebreak |
---|