CSS Stylesheet |
---|
img.confluence-embedded-image { display: inline-block !important; } |
add_workflow_docset_workflow | |
---|---|
APPRJID | SYM-21010 | AUTH1 | DEV1 | LDEV1 | SVT1 | LSVT1 |
AUTHJID | SYM-20480 |
for_techpubs | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Panel | ||||
---|---|---|---|---|
In this section:
|
...
Info |
---|
The third Ethernet port on the SBC 1000 is available only if running SBC 1000 v2 hardware. For hardware details, see Sonus Ribbon SBC 1000 Hardware Specifications. |
Warning |
---|
The Administrative IP port (available on the SBC 2000 only),should only be used for Running Initial Setup and disconnected when not in use (especially to avoid conflicts with your network). This interface cannot be used for VOIP media or protocols. |
Note | ||||
---|---|---|---|---|
| ||||
Note: The functionality of enabling and disabling system created logical interfaces (e.g. Ethernet 1, Ethernet 2, etc.) is available on the Sonus
|
...
Panel | ||||
---|---|---|---|---|
| ||||
Specifies the IP address mode that is assigned for that Logical Interface. Determines if the interface is IPv4, IPv6, or both. Valid entry: IPv4, IPv6 or Both. Default entry: IPv4. Depending on the mode selected, specific configuration fields are displayed; these are noted where applicable. |
Pagebreak |
---|
Panel | ||||
---|---|---|---|---|
| ||||
Note: This field is for SBC SWe Lite only. The VLAN tag is a value assigned for the sub-interface. |
...
Warning |
---|
Each logical interface can have a primary IP address and a secondary IP address. The secondary IP address is useful for WebUI or Sonus Ribbon SBC Edge API User's Guide operations only, and should not be used for VOIP media or protocols such as SIP, RTP and SRTP. |
...
Panel | ||||
---|---|---|---|---|
| ||||
Specifies how the IP address is assigned for that interface. Select from the drop down box. Available options: Static (User configured IPv4 address, netmask and system network configuration) or DHCP (Automatically acquired IPv4 address, netmask, and other system network configuration). Note: DHCP applies to IPv4 addresses only; IPv6 addresses must be statically configured. If you are configuring the IP Assign method from DHCP to Static, you should add a new default static route. We recommend this be done through the Modify Ethernet IP task (this allows you to set the IP address and the default route in one step). See Modifying the Sonus SBC 1000 IP Address and Modifying the Sonus SBC 2000 IP Address. WARNING: If you set the IP Assign method to DHCP, the DNS server(s), NTP server(s), domain name and the default IP Route will be overwritten and configured dynamically. |
Pagebreak |
---|
Panel | ||||
---|---|---|---|---|
| ||||
Specifies the Primary IP Address through which the Sonus
|
...
Panel | ||||
---|---|---|---|---|
| ||||
Specifies the Secondary IP Address through which the Sonus
|
...
Panel | ||||
---|---|---|---|---|
| ||||
Specifics whether a Split DNS should automatically be created using parameters supplied by the DHCP server. Available options:
This field is available only when the DHCP Options to Use field is set to IP Address and DNS. |
Pagebreak |
---|
Panel | ||||
---|---|---|---|---|
| ||||
Specifies the gateway to use for media calls traversing through that interface. |
...
Panel | ||||
---|---|---|---|---|
| ||||
Specifies the primary IPv6 network prefix length for the interface through which the SBC 1000/2000 communicates over Ethernet. Valid entry 1 - 127. Default value: 64. |
Panel | ||||
---|---|---|---|---|
| ||||
Specifies the gateway to use for media calls traversing through that interface. |
Pagebreak |
---|