| Add_workflow_for_techpubs |
|---|
| AUTH1 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca7f046c, userName='null'} |
|---|
| REV5 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909df, userName='null'} |
|---|
| REV6 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909df, userName='null'} |
|---|
| REV3 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cc5007d5, userName='null'} |
|---|
| REV1 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd5909dd, userName='null'} |
|---|
| REV2 | UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26ca6b044b, userName='null'} |
|---|
|
...
| borderColor | green |
|---|
| bgColor | transparent |
|---|
| borderWidth | 2 |
|---|
Back to Table of Contents
Back to Configuration
Back to Configuration - System Provisioning
Back to Category - Trunk Provisioning
Back to System Provisioning - Ip Signaling Profile
...
Use this object to specify use of domain names.
To View and Edit Domain Name
On SBC main screen, go to Configuration > System Provisioning > Category: Trunk Provisioning >
...
IP Signaling Profile > Egress
...
IP Attributes > Domain Name.
The Domain Name window is displayed.
...
On the Domain Name window,
...
...
...
from the drop-down list.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Trunk Provisioning - Egress Ip Attributes H323 Domian Name |
|---|
|
...
 Image Modified |
There are no Domain Names for DEFAULT_H323 type of Egress Ip Attributes.
DEFAULT_SIP
...
The Edit Domain Name window is displayed.
| Caption |
|---|
| 0 | Figure |
|---|
| 1 | Trunk Provisioning - Egress Ip Attributes SIP Domain Name |
|---|
|
| Image Added |
Image Removed
The following fields are displayed:
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Egress Ip Attributes Domain Name Parameters |
|---|
|
| |
...
...
SIP Domain Name In From Field | By default, uses its IP address as the host-port of the FROM URI in the outgoing INVITE message. Enable flag to use the originating gateway information returned in the policy response as the host-port of the FROM URI in the outgoing INVITE message. |
...
...
...
SIP Domain Name In From Field is enabled, the following parameters are available:
Preserve Ingress From Domain Name – If a SIP domain is configured for the ingress trunk group and this flag is enabled, the default gateway associated with that SIP domain will be the originating gateway. Otherwise, the originating gateway will be the default gateway associated with the SIP domain associated with the Softswitch entity.
|
...
...
...
...
| This parameter only applies when a Domain Name is configured for this zone. |
Use Lower Case Domain Names – Set flag to allow lower case domain name.
|
...
...
...
...
| This parameter only applies when a Domain Name is configured for this zone. |
|
Use |
...
SIP Domain Name In Request |
...
URI | Use SIP Domain Name In Request URI Flag. |
...
Disable (default)– includes the IP address in the host-port portion of the Request-URI in outgoing SIP INVITE messages.
|
...
Enable – includes the trunk group domain associated with egress trunk group as destination domain name in outgoing SIP INVITE messages.
When Use |
...
SIP Domain Name In Request
|
...
URI is enabled, the following parameters are available:
|
...
RURI Domain Name – Preserve Ingress R-URI Domain Name Flag. When enabled, the ERE/uses domain name received in the Request-URI as destination domain name in outgoing SIP INVITE messages. Normally, outgoing SIP INVITE messages contain the trunk group domain assigned to egress trunk group.
|
...
...
Use Lower Case Domain Names – Set flag to allow lower case domain name.
|
...
...
|
Use Zone Level Domain Name In Contact | Enable flag to use Zone level domain name in Contact header. |
...
...
...
IP Signaling Peer Domain In Request |
...
URI | Enable flag to use IP Signaling Peer Domain in Request URI.
|
Use SIP Domain in PAIHeader | Enable this flag to set the value of host port of the PAI URI equivalent to the value of the SIP domain name, which is configured on the ingress trunk group of the Policy Exchange Server (PSX). The options are: |
...
...
Make the required changes and click Save at the right hand bottom of the panel to save the changes made.