Versions Compared

Old Version 13

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: Automatic update to correct links

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb41059c, userName='null'}
JIRAIDAUTHSBX-90954
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd3e09ab, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c7cc0040, userName='null'}


Noprint
Panel
borderColorgreen
bgColortransparent
borderWidth2

Back to Table of Contents

Back to CLI Configure Mode

Back to Profiles - CLI

Back to Media - CLI


Panel

In this section:

Table of Contents
maxLevel3



Info
iconfalse

Related articles:

 

Include Page
Profile_NA_for_ePSXProfile_NA_for_ePSX


Overview

The Packet Service Profile supports up to four audio encoding entries, or Codecs, using ERE. The 

Spacevars
0series4
will negotiate a Codec from the list of Codecs allowed in the Packet Service Profile. One example of a negotiation scenario occurs when a call comes into the 
Spacevars
0product
from an H.323 peer. The 
Spacevars
0product
preferred coding may be G.711, while the H.323 gateway at the far end may prefer G.729A coding because that gateway has limited bandwidth to access the IP network.

In order to properly handle a call compression negotiation such as that described above, it is necessary to examine the codec list on both the local and remote gateway to find one or more codecs that are common to both. The precedence of the resultant codecs is controlled by the local precedence setting, or the precedence of the remote peer. This provisioning directive is provided by the honorRemotePrecedence parameter.

Refer to Packet Service Profile Provisioning Examples for provisioning examples.

Excerpt Include
Supported Codecs and Transcoding
Supported Codecs and Transcoding
nopaneltrue

Multiexcerpt

Audio Transparency

Spacevars
0series4
supports audio transparency in relaying unknown attributes and a subset of known attributes, such as rtpmap, fmtp, and T38 fax. The SBC also manages bandwidth for audio streams in pass-through calls. Audio transparency is controlled by the following PSP and Trunk Group parameters/flags.

Packet Service Profile:

  • Enable transcoderFreeTransparency for the session (enable on either of the PSPs)

  • Configure audioTransparency settings

  • Enable/disable reserveBwForPreferredAudioCommonCodec

SIP Trunk Group:

Refer to SBC SIP Transparency Implementation Guide for transparency implementation details.

Include Page
MultiExcerptNameSS_note


Info
titleNote

Avoid using both the Silence Suppression (SS) and non-SS variant of the same codec in one Packet Service Profile (PSP) because doing so can lead to extra offer-anwer handshakes and trigger a race condition while

Transparency_Profile_NoteTransparency_Profile_Note

Granular Control of HD Codec Offer or Answer

Excerpt
Both

the

Spacevars
0product

ERE and PSX support the following HD codec prioritization granular controls using Packet Service Profile. ERE functionality is described in this section.
  • Prioritization of HD codec over non-HD codec in the offer when the peer supports both HD and NB codecs even if transcoding is required
  • Prioritization of HD codec selection over non-HD codec in the answer
  • Support of Narrowband (NB) codec list only towards a peer supporting HD and NB codec for backward compatibility
The following

attempts to identify a common codec instead of simply transcoding the call.

Example using G.729A on the ingress trunk group, and using G.729AB on the egress trunk group to avoid this situation:

  • Ingress PSP: 711, 729A
  • Egress PSP: 711, 729AB
  • Transcode : Conditional
  • Conditions In Addition To No Common Codec : Different Silence Suppression,
  • Ingress This Leg: 711, 729
  • Egress This Leg: 711, 729



Audio Transparency

The 

Spacevars
0series4
supports audio transparency in relaying unknown attributes and a subset of known attributes, such as rtpmap, fmtp, and T38 fax. The
Spacevars
0product

flags are configurable in the Packet Service Profile configuration to support this feature. 
  • HDCodec Preferred
  • Prefer NBPassthru Over HDTranscode
  • Match Offered Codec Group If Nb Only
    • Force Route PSPOrder

     also manages bandwidth for audio streams in pass-through calls. Audio transparency is controlled by the following PSP and Trunk Group parameters/flags.

    Packet Service Profile

    Command Syntax

    :

    • Enable transcoderFreeTransparency for the session (enable on either of the PSPs)

    • Configure audioTransparency settings

    • Enable/disable reserveBwForPreferredAudioCommonCodec

    SIP Trunk Group:

    Refer to SBC SIP Transparency Implementation Guide for transparency implementation details.

    Include Page
    Transparency_Profile_Note
    Transparency_Profile_Note

    Granular Control of HD Codecs in Offers or Answers


    Multiexcerpt
    MultiExcerptNameHDCodec

    Both the

    Spacevars
    0product
    ERE and PSX provide control over HD codec prioritization through Packet Service Profile options. ERE functionality is described in this section.

    • Prioritization of an HD codec over a non-HD codec in the offer when the peer supports both HD and NB codecs, even if transcoding is required
    • Prioritization of a HD codec over a non-HD codec in the answer
    • Support of a narrowband (NB) codec list only toward a peer supporting HD and NB codecs, for backward compatibility

    The following

    Spacevars
    0product
    flags are configurable in the Packet Service Profile to control HD codec prioritization: 

    • HDCodec Preferred
    • Prefer NBPassthru Over HDTranscode
    • Match Offered Codec Group If Nb Only
    • Force Route PSPOrder


    Packet Service Profile

    Command Syntax

    Code Block
    languagenone
    % set profiles media packetServiceProfile <unique_profile_name> 
	aal1PayloadSize <0-999>
	audioTransparency <unknownCodecBitRate | unknownCodecPacketSize>
	codec <codecEntry1-codecEntry12> <codec> 
	dataCalls 
		initialPlayoutBufferDelay <5-50> 
		packetSize <10 | 20 | 30 | 40> 
		preferredRtpDataPayloadType <0-
    Code Block
    languagenone
    % set profiles media packetServiceProfile <unique_profile_name> 
	aal1PayloadSize <0-999>
	audioTransparency <unknownCodecBitRate | unknownCodecPacketSize>
	codec <codecEntry1-codecEntry12> <codec> 
	dataCalls 
		initialPlayoutBufferDelay <5-50> 
		packetSize <10 | 20 | 30 | 40> 
		preferredRtpDataPayloadType <0-127>
	dtls
		dtlsCryptoSuiteProfile <profile name>
		dtlsFlags 
			allowDtlsFallback <disable | enable>
			dtlsSctpRelay <disable | enable>
			dtlsSrtpRelay <disable | enable>			
			enableDtlsSrtp <disable | enable>
	flags 
	honorRemotePrecedence <disable | enable> 
	mediaPacketCos <0-7> 
	nonRtpStream
		maxNonRtpBandwidth <0-8000>
	packetToPacketControl
	peerAbsenceAction <none | peerAbsenceTrap | peerAbsenceTrapAndDisconnect> 
	preferredRtpPayloadTypeForDtmfRelay <0-128> 
	qosValues 
		applicationDscp <0-63>
        dtlsSctpDscp <0-255>
		msrpDscp <0-255>
	rtcpOptions
	secureRtpRtcp 
        t140Dscp <0-63>
	rtcpOptions <disable | enable>
	secureRtpRtcp 
		cryptoSuiteProfile <profile_name> 
		flags 
			allowFallback <disable | enable>
			allowPassthru <disable | enable>
			enableSrtp <disable | enable> 
			resetEncDecROCOnDecKeyChange <disable | enable>
			resetROCOnKeyChange <disable | enable>
			updateCryptoKeysOnModify <disable | enable>
	sendRoutePSPPrecedence <disable | enable> 
	silenceFactor <0-50> 
	silenceInsertionDescriptor 
		g711SidRtpPayloadType <0-127> 
		heartbeat <disable | enable> 
	t38 
		dataRateManagementType <type1LocalGenerationOfTcf | type2TransferOfTcf> 
		ecm ecmPreferred <disable | enable> 
		lowSpeedNumberOfRedundantPackets <0 | 1 | 2> 
		maxBitRate <2.4Kbits_s | 4.8Kbits_s | 9.6Kbits_s | 14.4Kbits_s> 
		numberOfRedundantPackets <0 | 1 | 2>
		protocolVersion <0 | 3>
	typeOfService <0-255> 
	videoCalls 
		audioOnlyIfVideoIsPrevented <disable | enable>
		codecListProfile <name>
		ieee8021QVLanCos <0-7>
		ipv4Tos <0-255>
		ipv6TrafficClass <0-255>
		maxVideoBandwith <0-50000 kbps> 
		videoBandwidthReductionFactor <0-100> 
	voiceInitialPlayoutBufferDelay <1-50>200 ms>

    Command Parameters

    The Packet Service Profile parameters are described below:

    Div
    classpdf6pttext


     
    Caption
    0Table
    1Packet Service Profile Parameters


    Parameter

    Length/Range

    Description

    packetServiceProfile

    N/A

    Specifies a unique identifier (name) for packet service profile. You can define any name or use Default as the parameter.

    aal1PayloadSize

    0-999

    The ATM Adaption Layer Type 1 (AAL-1) payload size (default = 47).

    audioTransparency N/A

    Use this object to configure Audio Transparency settings.

    • unknownCodecBitRate – The bit rate, in Kilobytes/second, required for bandwidth computation of unknown audio codecs. (range: 1-1000 KB/sec / default = 124)
    • unknownCodecPacketSize – The packet size, in milliseconds, required for Bandwidth computation of unknown audio codecs. (range: 5-100 ms / default = 10)
    Note

    NOTE: If the bandwidth is not configured, the unknownCodecPacketSize and unknownCodecBitRate are used for the pass-through call.

    codec

    codecEntry1-codecEntry12

    <codecEntry ID> <codec_name> – Defines the codec entry priorities and codec names. See

    Codec Parameters

    299928286 table below for details.

    Up to 12 codec configurations are supported by

    SBC

    the

    Spacevars
    0product
    for PSX,

    ePSX

    and Advanced ERE deployment scenarios (refer to Routing and Policy Management for a description of the different routing configurations).

    dataCalls

    N/A

    Data calls pertaining to restricted or unrestricted digital data.

    • initialPlayoutBufferDelay – Used for G.711 only. This is the initial playout delay for calls with a data bearer channel, for example, ISDN 64K data calls. This value is configured separately from the initial playout delay for voice channels (voiceInitialPlayoutBufferDelay) so providers can trade off delay on data calls versus the likelihood of jitter causing delay changes while the playout buffer adapts. Some data bearer calls are very sensitive to delay changes (such as H.320 video conferencing), so a higher initial delay should reduce the chance of jitter bursts causing problems. (range: 5-50 / default = 50).
    • packetSize <10 | 20 | 30 | 40> – The maximum data packet size (Kilobits). 
    • preferredRtpDataPayloadType – The RTP Payload Type included in the RTP header of the data packet.
      (range: 0-127 / default = 56)
    dtlsN/A

    Use this object to control DTLS-SRTP and DTLS fall-back behavior in this Packet Service Profile.

    • dtlsCryptoSuiteProfile <profile name> – Name of  Crypto Suite Profile to attach to this Packet Service Profile.
    • dtlsFlags
      • allowDtlsFallback <disable | enable> – Enable flag to allow fallback to standard RTP when cryptographic attribute negotiation fails (default = disable).
      • dtlsSctpRelay <disable | enable> –  Enable flag on both legs of the call to relay DTLS/SCTP streams to the endpoint (default = disable).

      • dtlsSrtpRelay <disable | enable> – Enable flag on both legs of the call to relay DTLS/SRTP audio and video streams to the endpoint. (default = disable).

      • enableDtlsSrtp <disable | enable> – Enable flag to allow Secure RTP.
    Note

    NOTE: DTLS-SRTP relay is a licensed feature and requires an SRTP license to be installed on

    SBC

    the

    Spacevars
    0product
    .

    Info

    NOTE: When a session contains DTLS-SRTP video stream or DTLS/SCTP application stream and there is no audio stream specified,

    SBC

    the

    Spacevars
    0product
    allows the session when the ingress and egress Packet Service Profiles (PSP) are configured as audio pass-through.

    If ICE is part of session establishment in WebRTC (WRTC) scenario, the relay mechanism implemented for DTLS-SRTP and DTLS/SCTP is supported independent of ICE processing.

    Refer to Configuring SBC for WRTC for additional WebRTC configuration details.

    flags

    N/A

    See

    Packet Service Profile Flags

    299928286 table below for flag descriptions.

    honorRemotePrecedence

    N/A

    Flag to set precedence of audio encoding priority order of the local packet service profile over the remote peers audio encoding priority order when creating the priority order of the audio encodings that are common to both. Options are:

    • disable (default) – Applies precedence to local audio encoding priority order, local Secure RTP/RTCP settings and crypto suite priority order.
    • enable – Applies precedence to the remote peer's audio encoding priority order. For ingress call legs, also applies precedence to remote peer's Secure RTP/RTCP settings and crypto suite priority order.

    mediaPacketCos

    0-7

    Specifies Class of Service (COS) value to be set in the IEEE 802.1D User Priority field of media packets transmitted on a call leg that uses this Packet Service Profile. This parameter only has an effect if the network interface supports 802.1Q tagged Ethernet frames. (default = 0 which is interpreted as best effort).

    packetToPacketControl
    nonRtpStreamN/A

    Use this object to

    define the packet-to-packet

    configure Non-RTP Stream settings.

    • maxNonRtpBandwidth - This attribute is added in the packet service profile to define the maximum allowed bandwidth for Non-RTP stream.
      NOTE: If you do not configure maxNonRtpBandwidth, the SBC assigns a default bandwidth of 32 Kbps for MSRP calls.

    packetToPacketControl

    		N/AUse this object to define the packet-to-packet control parameters. See
    Packet to Packet Control Parameters
    299928286 table below for details.

    peerAbsenceAction

    N/A

    Specifies the action to take when mediaPeerInactivity timer expires (refer to Media System - CLI page).

    • none – (default) Inactivity detection is disabled.
    • peerAbsenceTrap – Choose this option to generate a trap if RTP inactivity is detected.
    • peerAbsenceTrapAndDisconnect – Choose this option to generate a trap and tear down the call if RTP inactivity is detected.
    preferredRtpPayloadTypeForDtmfRelay

    0-128

    Specifies the preferred RTP payload type in the RTP header of audio packets for this encoding. (default = 128). This parameter is only used for 8 kHz clock rate. DTMF payload type of each subsequent clock rate (16 kHz, 24 kHz, etc.) is incremented by 1.

    Note

    NOTE: Using the default value of "128" for preferredRtpPayloadTypeForDtmfRelay implies that the preferred DTMF value (from the system configurable) is used for this profile.

    Note

    NOTE: If interworkDtmfWithoutTranscoding is enabled, ensure preferredRtpPayloadTypeForDtmfRelay is set to a valid value (96-127). If preferredRtpPayloadTypeForDtmfRelay value is invalid (set to "128"), the system may fail to pick up the value configured using "set system dspPad rtpDtmfRelay" command because DSPs are not used for the call.

    qosValuesN/A

    NOTE: The

    Spacevars
    0product
    uses the preferredRtpPayloadTypeForDtmfRelay configuration as the payload type for 8 kHz DTMF when not used by any other codec.

    For wideband (16 kHz) DTMF, the

    Spacevars
    0product
    uses the next available payload type (to the configured preferredRtpPayloadTypeForDtmfRelay value).

    qosValuesN/A

    Use this

    Use this

    object to configure the Quality of Service (QoS) DSCP value for this Packet Service Profile.

    • applicationDscp - Attribute for configuring qosValues for Application media type.
    • dtlsSctpDscp – Use this attribute to set the DSCP value in the Differentiated Services Field of the IP header for DTLS/SCTP packets that egress
    SBC
    • the
      Spacevars
      0product
      . (range: 0-255 / default = 0)
    • msrpDscp – Use this attribute to set the DSCP value to use for egressing MSRP packets (range: 0-255 / default = 0).

    rtcpOptions

    N/A

    Use this
    • t140Dscp – Use this parameter to specify the DSCP value for T.140 packets. Note: If the call type is t140 , then configure the DSCP value as DSCP T140 in the QOSValues parameter. (Range: 0-63 / default = 0).

    rtcpOptions

    N/A

    Use this object to specify Real Time Control Protocol (RTCP) options for the call. RTCP is used to report network traffic congestion data. Various actions (for example call disconnect) may be taken when congestion threshold settings are exceeded. See

    RTCP Options Parameters

    299928286 table below for details.

    secureRtpRtcp

    N/A

    Specifies whether secure RTP Real Time Control Protocol (SRTP) is enabled for the call:

    • cryptoSuiteProfile <profile name> – A unique identifier for the Cryptographic Suite Profile.
    • flags – Possible values are disable/enable. The default value of each flag below is "disable".
      • allowFallback – Enable flag to allow fallback to standard RTP/RTCP when crypto attribute negotiation fails.

      • allowPassthru – Enable flag to allow

    SBC

      • the

        Spacevars
        0product
        to pass-through SRTP media without authenticating, decrypting, or encrypting it internally.

    SBC

      • The

        Spacevars
        0product
        will prioritize SRTP pass-through media over terminated SRTP media. When this flag is disabled,

    SBC

      • the

        Spacevars
        0product
        terminates all SRTP and SRTCP media for authentication, encryption, or decryption.

    Note

      • NOTE: To use this flag, enableSrtp flag must be enabled.

      • enableSrtp – Enable this flag to enable secure RTP/RTCP.
      • resetEncDecROCOnDecKeyChange – Enable flag to reset Roll Over Counter for both encryption and decryption when decryption key changes.
      • resetROCOnKeyChange – Enable flag to reset the SRTP Roll Over Counter when the session key changes.
      • updateCryptoKeysOnModify – For an SRTP call, if this flag is enabled in Packet Service Profile and call leg mode is changed from sendonly/inactive/recvonly to sendrecv, the
    SBC
      • Spacevars
        0product
        generates a new set of crypto attributes.

    sendRoutePSPPrecedence

    N/A

    Use this flag to allow audio encoding order preference in outgoing messages only.

    • disable (default)
    • enable

    silenceFactor

    N/A

    The percentage of call time that silence is expected. This parameter is used to reduce expected call bandwidth. (range: 0-50 / default = 40).

    silenceInsertionDescriptor

    N/A

    Use this object to define the Silence Insertion Descriptor (SID) attributes.

    • g711SidRtpPayloadType – Specifies the G.711 Silence Insertion Descriptor (SID) RTP payloadType. (range: 0-127 / default = 19).
    • heartbeat – By default, this flag is enabled to allow SID packets to be sent within a minimal interval during a silence period (at least one SID packet must be sent within a SID maximum packet time frame).
      • disable
      • enable (default)

    t38

    N/A

    Use this object to specify T.38 data rate attributes using following parameters:

    • dataRateManagementType:
      • type1LocalGenerationOfTcf – Type 1 data rate management requires that the Training Check Frame (TCF) training signal is generated locally by the receiving gateway. Data rate management is performed by the emitting gateway based on training results from both PSTN connections. Type 1 is used for TCP implementations and is optionally used with UDP implementations.
      • type2TransferOfTcf – (default) Type 2 data rate management requires that the TCF is transferred from the sending gateway to the receiving gateway rather than having the receiving gateway generate it locally. Speed selection is done by the gateways in the same way as they would on a regular PSTN connection. Data rate management type 2 requires the use of UDP and is not recommended for use with TCP.
    • ecm – Use this flag to allocate DSP resources, when available, for T.38 Error Correction Mode (ECM) calls.
      • disable – (default) use normal resource allocation.
      • enable
    • lowSpeedNumberOfRedundantPackets – This field specifies the number of redundant IFP messages sent in a UDP packet for T.38 low speed fax transmission, and applies only if the T.38 error correction type is redundancy. (range: 0-2 / default = 1).
    • maxBitRate – Use this object to select the T.38 Maximum Bit Rate which controls and manipulates bits 11, 12, 13, and 14 in the DIS command received by the
    SBC
    • Spacevars
      0product
      from either the TDM circuit interface or the T.38 packet interface:
      • 2.4Kbits_s – For modem type ITU-T V.27ter fall-back mode.
      • 4.8Kbits_s – For modem type ITU-T V.27ter.
      • 9.6Kbits_s – For modem types ITU-T V.27ter and V.29.
      • 14.4Kbits_s – (default) For modem types ITU-T V.27ter, V.29, and V.17. This setting is used to constrain the type of modem modulation schemes.
    • numberOfRedundantPackets – Use this parameter for high-speed fax relay to specify the number of redundant Internet Facsimile Protocol (IFP) messages sent in a User Datagram Packet (UDP) for fax transmission. (range: 0-2 / default = 1).
    • protocolVersion – Use this parameter to specify the T.38 Fax protocol version to use.
      • 0 (default)
      • 3 

    typeOfService

    0-255

    Use this object

    to Use this parameter to set

    to set the six most significant bits of the "Type of Service" byte in

    an

    the IP header

    for DSCP marking of MSRP packets

    . Default value is 0.

    videoCalls

    N/A

    Use this object to define video call parameters.

    • audioOnlyIfVideoIsPrevented– By default, this flag is enabled to allow call to continue with the audio only portion if the video cannot be established for any reason.
      • disable
      • enable (default)
    • codecListProfile – Name of the Codec List profile used to store precedence and purge lists of video codec MIME sub-types.
    • ieee8021QVLanCos – IEEE-802 1Q VLAN Class of Service. (range: 0-7 / default = 0)
    • ipv4Tos – IPv4 type of service. (range: 0-255 / default = 0)
    • ipv6TrafficClass – IPv6 traffic class. (range: 0-255 / default = 0)
    Note
    • NOTE: ipv6TrafficClass is not supported with H.323 calls.
    • maxVideoBandwith – The maximum allowable session bandwidth (in kbps) for a call that includes video streams. This value Includes the bandwidth for all streams in the call (audio, video, BFCP, and so on). If "0" is set as the value, video calls are not allowed; and only audio calls can be set up following the normal allocation process (range: 0-50000 kbps / default = 10).
    • videoBandwidthReductionFactor – The amount, as a percentage, to reduce the session bandwidth allocation for calls that include video streams. This setting only affects the internal allocation of bandwidth used for the calls (does not affect the signaling). For example: if the reduction factor is "20", the bandwidth allocated for calls is reduced by 20%. In other words, if the normal bandwidth allocation for calls is 1000 kbps, a 20% reduction equates to a new 800 kbps bandwidth. (range: 0-100 / default = 0).

    voiceInitialPlayoutBufferDelay

    1-

    50The delay

    200

    Use this parameter to configure the initial playout buffer delay value (in milliseconds)

    by the initial playout buffer required to absorb the maximum expected data packet delay

    . Select a value just slightly greater than the maximum expected packet jitter across the network.

    Must

    The value must be in increments of 1 ms. (default = 10).

    NOTE: Using a value above 50 ms is not recommended during normal operation.



    Codec

    Command Syntax

    Code Block
    languagenone
    % set profiles media packetServiceProfile <unique_profile_name> codec <codecEntry1-codecEntry12> <codec name>

    Command Parameters

    Captioninfo
    0Table
    1Codec Parameters
    3Codec Parameters
     
    titleNote
    Note

    SBC-POL-RTU license is needed to enable more than four codecs.


    Caption
    0Table
    1Codec Parameters
    3Codec Parameters


    ParameterDescription
    codecEntry1 <codec name>Codec entry with a priority of "1" 
    codecEntry2 <codec name>Codec entry with a priority of "2" 
    codecEntry3 <codec name>Codec entry with a priority of "3" 
    codecEntry4 <codec name>Codec entry with a priority of "4" 
    codecEntry5 <codec name>Codec entry with a priority of "5" 
    codecEntry6 <codec name>Codec entry with a priority of "6" 
    codecEntry7 <codec name>Codec entry with a priority of "7" 
    codecEntry8 <codec name>Codec entry with a priority of "8" 
    codecEntry9 <codec name>Codec entry with a priority of "9" 
    codecEntry10 <codec name>Codec entry with a priority of "10" 
    codecEntry11 <codec name>Codec entry with a priority of "11" 

    codecEntry12 <codec name>

    Codec entry with a priority of "12".

    For each codecEntry ID, choose a <codec name>.

    Example default codec names are:

    • G711-DEFAULT (default codec)
    • G711SS-DEFAULT
    • G711_NONE
    • G723-DEFAULT
    • G723A-DEFAULT
    • G726-DEFAULT
    • G729A-DEFAULT
    • G729AB-DEFAULT

     



    Flags

    Command Syntax

    Code Block
    languagenone
    % set profiles media packetServiceProfile <unique_profile_name> flags 
	HDCodecPreferred <disable | enable>
	MatchOfferedCodecGroupIfNbOnly <disable | enable>
	digitDetectSendEnabled <disable | enable> 
	disallowDataCalls <disable | enable> 
	dscpPassthrough <disable | enable>
	forceRoutePSPOrder <disable | enable>
	interworkDtmfWithoutTranscoding <disable | enable>
	preferNBPassthruOverHDTranscode <disable | enable>
	reserveBwForPreferredAudioCommonCodec <disable | enable>
	ssrcRandomize <disable | enable>
	t140Call <disable | enable>
	useDirectMedia <disable | enable> 	
	validatePeerSupportForDtmfEvents <disable | enable>

    Command Parameters

     
    Caption
    0Table
    1Packet Service Profile Flags
    3Packet Service Profile Flags


    ParameterDescription
    HDCodecPreferred
    NoteThis flag only applies when
    Spacevars
    0product
    is configured with ePSX and/or external PSX.

    Enable flag to set HD codecs as preferred codec over non-HD codecs even if transcoding is required. When flag is disabled, continue with existing PSP/IPSP behavior.

    • disabled (default)
    • enabled

    When enabled, the following behavior is exhibited:

    If...Then...
    the ingress Offer contains any valid HD codecsHD codecs are sorted to the top of the list while sending out the Offer.
    all NB codecs are present
    SBC
    the
    Spacevars
    0product
    reorders the codec entries with NB first, followed by HD codecs.

     


    Codec selection priority from Answer message:

    1. HD-HD pass-through
    2. HD-HD transcoding
    3. NB-NB pass-through
    4. NB-NB transcoding
    5. HD-NB transcoding

     

    NOTE: This flag only applies when the

    Spacevars
    0product
    is configured with an external PSX.

    NOTE:

    Note

    If forceRoutePSPOrder flag is enabled, this flag does not affect the ordering of outgoing offer.

    Note

    NOTE: The flag transcoderFreeTransparency overrides this flag. If  transcoderFreeTransparency is enabled, this flag is ignored.

    MatchOfferedCodecGroupIfNbOnly

    Enable this flag to allow the

    SBC

    Spacevars
    0product
    to send only NB in outgoing offer if only NB is received in the ingress offer. Otherwise, do nothing. While sending the offer, this flag becomes is ignored if either HD-only or (HD+NB) is received in incoming offer.

    If this flag is disabled, the

    SBC

    Spacevars
    0product
    uses existing behavior.

    • disable (default)
    • enable
    Note

    NOTE: The flag transcoderFreeTransparency overrides this flag. If transcoderFreeTransparency is enabled, this flag is ignored.

    digitDetectSendEnabled

    Enable this flag to allow digit detection for pass-through calls on digits sent to the network.

    • disable (default)
    • enable
    NoteIf

    NOTE: Enable this flag to allow interworking without DSP resources

    is desired

    for this Packet Service Profile

    , this flag must be enabled

    .

    INFO: See 299928286 table below to understand which PSP leg to enable this flag for the desired KPML functionality.

    disallowDataCallsEnable flag to disallow data calls.
    • disable (default)
    • enable
    dscpPassthrough

    When enabled on both the Ingress and Egress call leg, the DSCP value in the IP header of the media packets is transparently passed through the system. Once media is received from the peer, any value set in the typeOfService field on the Packet Service Profile has no effect when dscpPassthrough is configured on both legs for the associated call.

    • disable (default)
    • enable

    forceRoutePSPOrder

    Enable this flag to send the outgoing offer in the same order as egress route Packet Service Profile irrespective of HD/NB priorities.

    • disable (default)
    • enable
    Note

    NOTE: If this flag is enabled, HDCodecPreferred flag does not affect the ordering of outgoing offer.

    Note

    NOTE: The flag transcoderFreeTransparency overrides this flag. If  transcoderFreeTransparency is enabled, this flag is ignored.

    interworkDtmfWithoutTranscoding

    Enable flag to interwork DTMF with out-of-band RFC2833 without the use of transcoding (DSP resources).

    • disable (default)
    • enable
    Note

    NOTE: If interworkDtmfWithoutTranscoding is enabled, ensure preferredRtpPayloadTypeForDtmfRelay is set to a valid value (96-127). If preferredRtpPayloadTypeForDtmfRelay value is invalid (set to "128"), the system may fail to pick up the value configured using "set system dspPad rtpDtmfRelay" command because DSPs are not used for the call.

    mediaLockDownForPassThroughThis flag is deprecated.
    policeOnHeaviestAudioCodec

    When enabled,

    SBC reserves the worst Note

    the

    Spacevars
    0product
    reserves the worst case common codec bandwidth on trunk groups and interfaces, but polices on maximum bandwidth for all codecs from Offer or Answer in a pass-through call.

    • disable (default)
    • enable

     

    NOTE: This configuration applies to all pass-through calls. It works independently from the Audio Transparency feature

    and reserveBwForPreferredAudioCommonCodec

    and reserveBwForPreferredAudioCommonCodec flag.

    preferNBPassthruOverHDTranscode

    Enable this flag to allow the

    SBC

    Spacevars
    0product
    to choose NB-NB pass-through over HD-HD transcoded call.

    When disabled, the

    SBC

    Spacevars
    0product
    prefers HD-HD transcoded call over NB-NB pass-through.

    • disable (default)
    • enable
    Info

    NOTE: This flag is valid only if HDCodecPreferred flag is enabled, and is applied when selecting a codec from answer.

    Note

    NOTE: The flag transcoderFreeTransparency overrides this flag. If  transcoderFreeTransparency is enabled, this flag is ignored.

    reserveBwForPreferredAudioCommonCodec

    By default, the

    SBC

    Spacevars
    0product
    reserves the worst case common audio codec bandwidth for pass-through calls on trunk groups and IP interfaces, and polices the same bandwidth. Use this flag to reserve the bandwidth associated with the preferred common codec and police on the worst case codec. This flag applies to both known and unknown codecs, and can be used independently or in conjunction with Audio Transparency feature.

    • disable (default)
    • enable
    Note

    NOTE: This flag is active for a call when both the PSPs have this flag enabled. If this flag is disabled in any of the PSPs, the flag is not applied.

     ssrcRandomize

    Enable flag to generate a new SSRC (using a random value) along with a new

    time stamp

    timestamp on a new RTP stream whenever a resource is reactivated (due to change in codec, etc.). SSRC randomization reduces the probability of collision in large groups and simplifies the process of group sampling that depends on uniform distribution of SSRCs.

    • disable (default)
    • enable 
    useDirectMedia
    t140Call

    Enable flag to

    use direct media as needed

    allow text media calls using T.140 codec.

    • disable (default)
    • enable

    validatePeerSupportForDtmfEvents

    Flag to validate peer support for DTMF events.

    NOTE: The

    Spacevars
    0product
    does not validate, prioritize, or purge any codec or attributes received for the text media. Any required validation is performed by the endpoints.

    Refer to Text Codecs for additional details of text codec support.

     

    useDirectMedia

    Enable flag to use direct media as needed.

    • disable (default)
    • enable

    validatePeerSupportForDtmfEvents

    Flag to validate peer support for DTMF events. Enable this flag for all peer devices that support RFC 4733.

    • disable (default) – 
      Spacevars
      0product
      does not validate the presence of DTMF events in the offer or answer from the peer. If DTMF relay is enabled, 
      Spacevars
      0product
      transmits DTMF digits received from the other leg to this peer using the named event RTP payload.
    • enable
    – 
    • – The
      Spacevars
      0product
      validates the presence of DTMF events in the offer or answer from peers that support RFC 4733. If DTMF Relay is enabled and events 0-15 are received (with no other combination or subset of events),
     
    •  the
      Spacevars
      0product
      forwards the events in the egress leg to this peer using the named event RTP payload.
    When 
    • When the
      Spacevars
      0product
      is configured for a pass-through call and it receives DTMF events other than 0-15 from the ingress peer, it does not offer any DTMF events to the egress endpoint.

    Packet to Packet Control

    Command Syntax

    Code Block
    languagenone
    % set profiles media packetServiceProfile <unique_profile_name>  packetToPacketControl

	codecsAllowedForTranscoding 
		otherLeg <amr | efr | evrc | g711a | g711u | g722 | g726 | g729 | g7221 | g7222 | g7231 | ilbc | opus | t38> 
		thisLeg <amr | efr | evrc | g711a | g711u | g722 | g726 | g729 | g7221 | g7222 | g7231 | ilbc | opus | t38> 
	conditionsInAdditionToNoCommonCodec
		applyFaxToneTreatment <disable | enable>
		different2833PayloadType <disable | enable>
		differentDtmfRelay <disable | enable> 
		differentPacketSize <disable | enable> 
		differentSilenceSuppression <disable | enable> 
		honorAnswerPreference <disable | enable>
		honorOfferPreference <disable | enable> 
	transcode <conditional | determinedByPspForOtherLeg | only | transcoderFreeTransparency>

    Command Parameters

    Caption
    0Table
    1Packet to Packet Control Parameters
    3Packet to Packet Control Parameters
     



    Anchor
    Digit Detect Send Enabled Settings for KPML
    Digit Detect Send Enabled Settings for KPML
    Digit Detect Send Enabled Settings for KPML


    Multiexcerpt
    MultiExcerptNamedigitDetectSendEnabled

    Use the following table for guidance in setting the Digit Detect Send Enabled flag on each PSP leg to achieve the desired Key Press Markup Language (KPML) functionality.

    Info
    titleInfo

    Refer to  KPML DTMF Support section on the page DTMF and RTP Relay for feature details.


    Caption
    0Table
    1Digit Detect Send Enabled Settings for KPML


    Ingress PSPEgress PSPKPML Subscription Leg
    EnableEnableEgress / Ingress
    DisableEnableEgress / Ingress with stream reverse
    EnableDisableIngress / Egress with stream reverse
    DisableDisableNone



     


    Packet to Packet Control

    Command Syntax

    Code Block
    languagenone
    % set profiles media packetServiceProfile <unique_profile_name>  packetToPacketControl

	codecsAllowedForTranscoding 
		otherLeg <amr | efr | evrc | g711a | g711u | g722 | g726 | g729 | g7221 | g7222 | g7231 | ilbc | opus | t38> 
		thisLeg <amr | efr | evrc | g711a | g711u | g722 | g726 | g729 | g7221 | g7222 | g7231 | ilbc | opus | t38> 
	conditionsInAdditionToNoCommonCodec
		applyFaxToneTreatment <disable | enable>
		different2833PayloadType <disable | enable>
		differentDtmfRelay <disable | enable> 
		differentPacketSize <disable | enable> 
		differentSilenceSuppression <disable | enable> 
		honorAnswerPreference <disable | enable>
		honorOfferPreference <disable | enable> 
	transcode <conditional | determinedByPspForOtherLeg | only | transcoderFreeTransparency>

    Command Parameters


    Caption
    0Table
    1Packet to Packet Control Parameters
    3Packet to Packet Control Parameters


    ParameterDescription
    codecsAllowedForTranscoding

     Use this parameter to specify codecs allowed for transcoding, and which leg to apply them to.

      • otherLeg <codec> (see codec list below)
      • thisLeg <codec> (see codec list below)

    Codec list:

    amr  | efr |  evrc | g711a | g711u | g722 | g726 | g729 | g7221 | g7222 | g7231 | ilbc | opus | silk | t38


    conditionsInAdditionToNoCommonCodec

     The 

    Spacevars
    0product
    performs transcoding when any of the specified conditions are met, including no common codec on ingress and egress legs.

    • applyFaxToneTreatment– Apply fax tone treatment.
      • disable (default)
      • enable
    •  different2833PayloadType– Enable this option to allow the
      Spacevars
      0product
      to transcode media when RFC2833 payload type received from ingress is different from the preferred DTMF payload type configured in egress PSP.
      • disable (default)
      • enable
    • differentDtmfRelay – Enable this flag to perform transcoding when the ingress and egress call legs use different DTMF relay methods.
      • disable (default)
      • enable
    • differentPacketSize – Enable this flag to perform transcoding when the ingress and egress call legs use different packet sizes.
      • disable (default)
      • enable
    • differentSilenceSuppression –Enable this flag to perform transcoding when the ingress and egress call legs use different silence suppression methods.
      • disable (default)
      • enable
    • honorAnswerPreference– The
      Spacevars
      0product
      triggers a new offer towards the other side when an answer is received for a re-INVITE from this side. The re-INVITE generated on the other side carries all possible codecs in Route Packet Service Profile that causes the most preferred codec of the other side peer to be modified. Enable this Honor Answer Preference (HAP) flag to lock down the most preferred codec towards the peer irrespective of re-INVITE received for mid-call modification from this side. (See the table below describing
      Spacevars
      0product
      behavior when this flag is enabled/disabled)
    ParameterDescriptioncodecsAllowedForTranscoding

     Use this parameter to specify codecs allowed for transcoding, and which leg to apply them to.

      • otherLeg <codec> (see codec list below)
      • thisLeg <codec> (see codec list below)

    Codec list:

    amr  | efr |  evrc | g711a | g711u | g722 | g726 | g729 | g7221 | g7222 | g7231 | ilbc | opus | t38

     

    conditionsInAdditionToNoCommonCodec

     The 

    Spacevars
    0product
    performs transcoding when any of the specified conditions are met, including no common codec on ingress and egress legs.

    applyFaxToneTreatment– Apply fax tone treatment
    • .
      • disable (default)
      • enable
     different2833PayloadType
    • honorOfferPreference – Enable this
    option to allow SBC to transcode media when RFC2833 payload type received from ingress is different from the preferred DTMF payload type configured in egress PSP
    • Honor Offer Preference (HOP) flag to honor the codec preference of the peer's offer when the 'Honor Remote Preference' flag on the PSX is enabled.  This option is available only when transcode = conditional. (See 299928286 table below describing
      Spacevars
      0product
      behavior when this flag is enabled/disabled).
      • disable (default)
      • enable
    differentDtmfRelay – Enable this flag to perform transcoding when the ingress and egress call legs use different DTMF relay methods.disable
    transcode
    Transcode options:
      • conditional (default)
  • enable
  • differentPacketSize – Enable this flag to perform transcoding when the ingress and egress call legs use different packet sizes.
    • disable (default)
    • enable
  • differentSilenceSuppression –Enable this flag to perform transcoding when the ingress and egress call legs use different silence suppression methods.
    • disable (default)
    • enable
  • honorAnswerPreference– The SBC triggers a new offer towards the other side when an answer is received for a re-INVITE from this side. The re-INVITE generated on the other side carries all possible codecs in Route Packet Service Profile that causes the most preferred codec of the other side peer to be modified. Enable this Honor Answer Preference (HAP) flag to lock down the most preferred codec towards the peer irrespective of re-INVITE received for mid-call modification from this side. (See the table below describing SBC behavior when this flag is enabled/disabled).
    • disable (default)
    • enable
  • honorOfferPreference – Enable this Honor Offer Preference (HOP) flag to honor the codec preference of the peer's offer when the 'Honor Remote Preference' flag on the PSX is enabled.  This option is available only when transcode = conditional. (See honorAnswerPreference vs. honorOfferPreference table below describing SBC behavior when this flag is enabled/disabled).
    • disable (default)
    • enable
    • transcodeTranscode options:
      • conditional (default)
      • determinedByPspForOtherLeg
      • only
      • transcoderFreeTransparency (NOTE:  If using this option, you must also set lateMediaSupport to ‘passthru’ (refer to sipTrunkGroup media - CLI).
    Multiexcerpt
    MultiExcerptNameTranscodeConditional

    The SBC, when configured with the appropriate codecs, transcodes for differences in the codecs. Use ‘transcode conditional’ option to allow the SBC to transcode for certain conditions in addition to differences in codecs. For example, if the codecs are the same on both legs and this option is selected, by applying additional settings for the particular call scenarios, the SBC will trigger transcoding for those scenarios, such as:

    1. Transcode for DTMF differences. For example, when both legs have same codec, but one uses inband for DTMF and the other RFC 2833.
    2. Transcode for Silence Suppression differences.
    3. Transcode for Packet Size differences.
    4. Transcode for RFC2833/4733 Payload differences. For example, when codecs are the same on both legs, but one side uses 101 as the Payload Type for DTMF and the other uses 102.
    5. Transcode always.
    Caption
    0Table
    1honorAnswerPreference vs. honorOfferPreference
    3honorAnswerPreference vs. honorOfferPreference
     
    HOP Flag StateHAP Flag StateSBC Behavior
    enabledisableThe
    Spacevars
    0product
    selects a codec order of precedence in the offered SDP, irrespective of whether it is a pass-through or transcoded codec (if transcoding is defined for that codec). The
    Spacevars
    0product
    as part of media lock-down may send a re-INVITE to egress peer. Note that the preference on the answer side is given to a pass-through codec.
    enableenableThe
    Spacevars
    0product
    gives preference to HAP over HOP in case of conflict. The Honor Remote Preference (HRP) flag on the answer leg decides the preference order. Based on that preference list, the
    Spacevars
    0product
    selects a codec with highest preference from answer SDP that can be used even if it requires transcoding. Note that this may cause the selection of a codec on the other side leg not to be honored. This happens in case of a pass-through call.
    disableenableThe
    Spacevars
    0product
    gives preference to answer codec order that is created based on HRP flag. The most preferred codec is chosen as received in the answer SDP, irrespective of whether it is a pass-through or a transcoded codec (if transcoding is defined for that codec).

    RTCP Options

    Command Syntax

    Code Block
    languagenone
    % set profiles media packetServiceProfile <unique_profile_name> rtcpOptions rtcp <disable | enable>
	enableRTCPForHeldCalls <disable | enable>
	packetLossAction <none | packetLossTrap | packetLossTrapAndDisconnect>
	packetLossThreshold <0-32767>
	rrBandwidth <100-4000>
	rsBandwidth <100-3000>
	terminationForPassThrough <disable | enable>

    Command Parameters

    Caption
    0Table
    1RTCP Options Parameters
    3RTCP Options Parameters
     

    ParameterLength/RangeDescription rtcpN/A

    Enable flag to use RTCP for the call.

    • disable (default)

    • enable

    Note

    The below attributes are only available to configure RTCP once this flag is enabled.

    enableRTCPForHeldCallsN/A

    If this flag is enabled, the

    Spacevars
    0product
    ignores the configured RR/RS values in the Packet Service Profile (PSP) and sends RR/RS = 0 in the offer/answer, plus disables RTCP when the call is active.

    When the call is HELD, and a RE-INVITE is sent, the

    Spacevars
    0product
    uses the configured values in the PSP for RTCP bandwidth and enables RTCP. When the call is RESUMED, the
    Spacevars
    0product
    again disables RTCP by sending RR/RS=0 in the RE-INVITE.

    • disable (default)

    • enable

    packetLossActionN/APacket loss action to take when packet threshold is exceeded:
    • none – Take no action.
    • packetLossTrap – Generate trap.
    • packetLossTrapAndDisconnect – Generate trap and disconnect.
    packetLossThreshold 0-32767

    Enter a value to specify the packet loss threshold value (number of lost packets per 100,000 packets) to trigger a packet loss action (default = 0).

    This parameter is required if RTCP is enabled. When set to “0”, no packet loss inactivity detection is performed. See Command Examples below for an example configuration.

    This setting can be used in conjunction with  mediaPeerInactivity (refer to mediaPeerInactivity parameter in Media System - CLI page).

    Note

    Since configuring this parameter to a value less than 400 disables threshold detection, use a value in the range of 400 to 32767 to enable threshold detection.

    rrBandwidth100-4000<rrBandwidth value> – The RTCP bandwidth allocated to active data senders (default = 250).rsBandwidth100-3000<rsBandwidth_value> – The RTCP bandwidth allocated for receivers (default = 250). 

    terminationForPassThrough

    N/A
      • determinedByPspForOtherLeg
      • only
      • transcoderFreeTransparency

    NOTE: If using Transcoder Free Transparency option "transcoderFreeTransparency", you must also set lateMediaSupport to ‘passthru’ (refer to SIP Trunk Group - Media - CLI)

    NOTE: Transcoder Free Transparency takes precedence over Packet Service Profile flags when enabled on either the ingress trunk group or egress trunk group PSP leg allowing the

    Spacevars
    0product
    to bypass transcoding and codec policies that result in removing/deleting codecs.


    Multiexcerpt
    MultiExcerptNameTranscodeConditional

    NOTE: The

    Spacevars
    0product
    , when configured with the appropriate codecs, transcodes for differences in the codecs. Use ‘transcode conditional’ option to allow the
    Spacevars
    0product
    to transcode for certain conditions in addition to differences in codecs. For example, if the codecs are the same on both legs and this option is selected, by applying additional settings for the particular call scenarios, the
    Spacevars
    0product
    will trigger transcoding for those scenarios, such as:

    1. Transcode for DTMF differences. For example, when both legs have same codec, but one uses inband for DTMF and the other RFC 2833.
    2. Transcode for Silence Suppression differences.
    3. Transcode for Packet Size differences.
    4. Transcode for RFC2833/4733 Payload differences. For example, when codecs are the same on both legs, but one side uses 101 as the Payload Type for DTMF and the other uses 102.
    5. Transcode always.


    Caption
    0Table
    1honorAnswerPreference vs. honorOfferPreference
    3honorAnswerPreference vs. honorOfferPreference


    HOP Flag StateHAP Flag StateSBC Behavior
    enabledisable
    The
    Spacevars
    0product
    selects a codec order of precedence in the offered SDP, irrespective of whether it is a pass-through or transcoded codec (if transcoding is defined for that codec). The
    Spacevars
    0product
    as part of media lock-down may send a re-INVITE to egress peer. Note that the preference on the answer side is given to a pass-through codec.
    enableenable
    The
    Spacevars
    0product
    gives preference to HAP over HOP in case of conflict. The Honor Remote Preference (HRP) flag on the answer leg decides the preference order. Based on that preference list, the
    Spacevars
    0product
    selects a codec with highest preference from answer SDP that can be used even if it requires transcoding. Note that this may cause the selection of a codec on the other side leg not to be honored. This happens in case of a pass-through call.
    disableenable
    The
    Spacevars
    0product
    gives preference to answer codec order that is created based on HRP flag. The most preferred codec is chosen as received in the answer SDP, irrespective of whether it is a pass-through or a transcoded codec (if transcoding is defined for that codec).

    RTCP Options

    Info

    References:


    Command Syntax

    Code Block
    languagenone
    % set profiles media packetServiceProfile <unique_profile_name> rtcpOptions rtcp <disable | enable>
	enableRTCPForHeldCalls <disable | enable>
	packetLossAction <none | packetLossTrap | packetLossTrapAndDisconnect>
	packetLossThreshold <0, 400-32767>
	rrBandwidth <100-4000>
	rsBandwidth <100-3000>
	rtcpMux <disable | enable>
    rtcpXr <disable | relay | relayOrTerminate>
	terminationForPassThrough <disable | enable>

    Command Parameters


    Caption
    0Table
    1RTCP Options Parameters
    3RTCP Options Parameters


    ParameterLength/RangeDescription 
    rtcpN/A

    Enable flag to use RTCP for the call.

    • disable (default)

    • enable

    NOTE: The below attributes are only available to configure RTCP once this flag is enabled.

    enableRTCPForHeldCallsN/A

    If this flag is enabled, the

    Spacevars
    0product
    ignores the configured RR/RS values in the Packet Service Profile (PSP) and sends RR/RS = 0 in the offer/answer, plus disables RTCP when the call is active.

    When the call is HELD, and a RE-INVITE is sent, the

    Spacevars
    0product
    uses the configured values in the PSP for RTCP bandwidth and enables RTCP. When the call is RESUMED, the
    Spacevars
    0product
    again disables RTCP by sending RR/RS=0 in the RE-INVITE.

    • disable (default)

    • enable

    packetLossActionN/APacket loss action to take when packet threshold is exceeded:
    • none – Take no action.
    • packetLossTrap – Generate trap.
    • packetLossTrapAndDisconnect – Generate trap and disconnect.
    packetLossThreshold 0, 400-32767

    Enter a value to specify the packet loss threshold value to trigger a packet loss action (default = 0).

    This parameter is required if RTCP is enabled. When set to “0”, no packet loss inactivity detection is performed. See Command Examples below for an example configuration.

    This setting can be used in conjunction with  mediaPeerInactivity (refer to mediaPeerInactivity parameter in Media System - CLI page).

    rrBandwidth100-4000<rrBandwidth value> – The RTCP bandwidth allocated to active data senders (default = 250).
    rsBandwidth100-3000<rsBandwidth_value> – The RTCP bandwidth allocated for receivers (default = 250). 
    rtcpMuxN/A

    Enable this flag for the ingress or egress Packet Service Profile for the

    Spacevars
    0product
    to use RTCP-Mux on the respective call leg.

    Multiexcerpt include
    MultiExcerptNameRTCP Mux
    PageWithExcerptSDP Support

    • disable (default)
    • enable

    Refer to SDP Support for additional RTCP Mux details.

    NOTE: This flag is only applicable for SIP Trunk Groups.

    rtcpXrN/A

    Specifies control of RTCP-XR block processing and statistics collection.

    • disable (default) - retains existing default behavior (no statistics collection).
    • relay - Allows end-to-end XR block relay (only) and statistics collection if end-to-end peer negotiation for RTCP-XR (a=rtcp-xr:voip-metrics) relay is successful; otherwise XR block is dropped.
    • relayOrTerminate - Allows end-to-end XR block relay or per-leg termination if end-to-end negotiation for RTCP-XR relay is not successful (only one leg supports RTCP-XR). This setting guarantees XR block termination and statistics collection on any call leg where XR blocks are received.

    terminationForPassThrough

    		N/A

    Use this flag to specify

    Specifies

    RTCP termination behavior for pass-through calls.

    • disable
    –
    • (default)– RTCP is relayed between the end points for pass-through calls. 
    • enable – Enable flag (as well as rtcp flag) on one leg to terminate RTCP sessions on each leg for pass-through calls. If RTCP and RTCP termination is enabled on one leg of a pass-through call, RTCP is terminated and originated for that leg. If RTCP is enabled on both legs on the pass-through call, irrespective of terminationForPassThrough settings, RTCP is always relayed.


    Include Page
    Packet_Loss_Threshold_note
    Packet_Loss_Threshold_note


    Anchor
    example
    example
    Command Examples

    To configure RTCP options:

    Code Block
    languagenone
    % set profiles media packetServiceProfile PSP-1 rtcpOptions rtcp enable
% set profiles media packetServiceProfile PSP-1 rtcpOptions packetLossAction packetLossTrap
% set profiles media packetServiceProfile PSP-1 rtcpOptions packetLossThreshold 10000
% commit

% show profiles media packetServiceProfile PSP-1
rtcpOptions {
rtcp enable;
packetLossThreshold 10000;
packetLossAction packetLossTrap;
}

    To configure PSP to transcoderFreeTransparency on both legs:

    Code Block
    languagenone
    % set profiles media packetServiceProfile PSP_INT packetToPacketControl transcode transcoderFreeTransparency 
% set profiles media packetServiceProfile PSP_EXT packetToPacketControl transcode transcoderFreeTransparency

    To configure audioTransparecy feature on both legs:

    Code Block
    languagenone
    % set profiles media packetServiceProfile PSP_INT audioTransparency unknownCodecBitRate 124
% set profiles media packetServiceProfile PSP_EXT audioTransparency unknownCodecBitRate 124

% set profiles media packetServiceProfile PSP_INT audioTransparency unknownCodecPacketSize 10
% set profiles media packetServiceProfile PSP_EXT audioTransparency unknownCodecPacketSize 10

% set profiles media packetServiceProfile PSP_INT flags reserveBwForPreferredAudioCommonCodec enable
% set profiles media packetServiceProfile PSP_EXT flags reserveBwForPreferredAudioCommonCodec enable

    To allow secure RTP plus relaying of SRTP audio and video streams and SCTP packet streams, and then to set the DSCP value in the Differentiated Services Field of the IP header for DTLS/SCTP packets that egress SBCthe 

    Spacevars
    0product
    .

    Code Block
    languagenone
    % set profiles media packetServiceProfile DEFAULT dtls dtlsFlags enableDtlsSrtp enable dtlsSrtpRelay enable dtlsSctpRelay enable
% set profiles media packetServiceProfile DEFAULT qosValues dtlsSctpDscp 100 %100 
% commit
% exit

> show table profiles media packetServiceProfile DEFAULT dtls 
dtlsFlags {
    allowDtlsFallback enable;
    enableDtlsSrtp    enable;
    dtlsSrtpRelay     enable;
    dtlsSctpRelay     enable;
}

> show table profiles media packetServiceProfile DEFAULT qosValues 
msrpDscp     100;
dtlsSctpDscp 100;

    Pagebreak