Versions Compared

Old Version 13

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'}
JIRAIDAUTHSYM-2300024331
REV5UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26c87d01118a00a02355cd1c2f0155cd26cd700a1f, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cc5207f0, userName='null'}

...

Panel

In this section...

Table of Contents
maxLevel2

Note

SBC Edge will support now supports a new deployment with CCE 2.1.0 in release 7.0.1.

If Before this release, if your CCE auto-updates to CCE 2.1.0:

  • To rerun the step “Transfer Credential from SBC”, it will require 7.0.1.

...

In this best practice the router/firewall is configured with the following rules:

Caption
0Table
1Internal Firewall Rules for CCE

Source IP

Destination IP

Source Port

Destination Port

Cloud Connector Mediation component – 192.168.210.123 & 192.168.210.117

Internal clients

TCP 49 152 – 57 500*

TCP 50,000-50,019 (Optional)

Cloud Connector Mediation component – 192.168.210.123 & 192.168.210.117

Internal clients

UDP 49 152 – 57 500*

UDP 50,000-50,019

Internal clients

Cloud Connector Mediation component – 192.168.210.123 & 192.168.210.117

TCP 50,000-50,019

TCP 49 152 – 57 500*

Internal clients

Cloud Connector Mediation component – 192.168.210.123 & 192.168.210.117

UDP 50,000-50,019

UDP 49 152 -57 500*

Caption
0Table
1External Firewall Rules for CCE

Source IP

Destination IP

Source Port

Destination Port

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

Any

TCP 5061

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

Any

TCP 80

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

Any

UDP 53

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

Any

TCP 53

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

TCP 50,000-59,999

Any

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

UDP 3478

Any

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

UDP 50,000-59,999

Any

Any

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

TCP 5061

Any

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

TCP 443

Any

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

TCP 50,000-59,999

Any

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

UDP 3478

Any

Cloud Connector Edge External Interface – 192.168.211.81 & 192.168.211.86

Any

UDP 50,000 - 59,999

Caption
0Table
1Host Firewall Rules - Internal or External Access
Source IP Destination IPSource PortDestination Port
ASMAnyAnyTCP 53
ASMAnyAnyTCP 80
ASMAnyAnyTCP 443
 
 

Multiexcerpt include
MultiExcerptNameDNSSettings
PageWithExcerptConfiguring the SBC Edge for a Single CCE

...

StepAction
1Login to the WebUI of the SBC Edge.
2Navigate to Tasks  > Office 365 Cloud Connector Edition> Setup.
3Click the Configure CCE tab.
4

Configure all necessary information and then click OK.

Note

TLS 1.2 is supported; the following fields are required to configure TLS:

  • Primary SBC Transport Protocol. Options: TCP or TLS (supports TLS 1.2).
  • Secondary SBC Transport Protocol (optional). Options: TCP or TLS (supports TLS 1.2).

If TLS is configured as the Primary SBC Transport Protocol, you must run the Synchronize CCE/SBC CA Certificate task to allow a successful TLS handshake between CCE and SBC Edge. However, if TCP is configured as the Primary SBC Transport Protocol the Synchronize CCE/SBC CA Certificate task is not mandatory. See Managing Cloud Connector Edition Private Certificates.

Caption
0Figure
1Configuring the ASM – CCE-1

Image RemovedImage Added

Caption
0Figure
1Configuring the ASM – CCE-2

Image RemovedImage Added

 

Note: Enterthe ASM's IP address in the HA Master IP Address field. The Slave uses the same root certification as the Master, and this location contains the shared folder that contains the Root CA of the Master.

5After receiving the activity status as successfully completed, click the Prepare CCE tab to continue.

To increase Fast Failover (which shortens the time where certain ported numbers have a long delay from ITSP PSTN provider) configure Trunk Information:

Refer Support. Indicates whether Gateways support Refer for a Call Transfer scenario. Valid entries: Enable (the Gateway(s) supports Refer which can handle call transfer) or Disable (the Gateway does not support Refer and the Mediation Server handles call transfer).

Fast Failover Timer. Determines whether outbound calls that are not answered by the gateway within ten seconds will be routed to the next available trunk; if there are no additional trunks, the call will automatically be dropped. Valid entries: Enable or Disable.

Forward Call History. Indicates whether call history information is forwarded through the trunk. Valid entries: Enable or Disable.

Forward PAI. Indicates whether the P-Asserted-Identity (PAI) header will be forwarded along with the call. Valid entries: Enable or Disable.

6After receiving the activity status as successfully completed, click the Prepare CCE tab to continue.
Warning

 If the deployment environment consists of multiple-site with a

Warning

 If the deployment environment consists of multiple-site with a single certificate, or a wild card certificate, ensure the CCE Site Name and the Edge Server Public Hostname are correct before proceeding.

...

 

Caption
0Figure
1Building your SBC Edge-2 Configuration

 

Multiexcerpt include
MultiExcerptNameBasicCallVerification
PageWithExcerptConfiguring the SBC Edge for a Single CCE

Multiexcerpt include
MultiExcerptNameO365KnownIssues
PageWithExcerptConfiguring the SBC Edge for a Single CCE

Updating the CCE Password

Follow these steps if you need to update the O365 tenant admin password or account.

StepAction
1On the WebUI, run Preparing the CCE to specify a new Password. Select the existing password and enter the new password. Only the O365 should be modified for a running instance of CCE.
Action
1On the WebUI, click Tasks and select the Prepare CCE tab (see Preparing the CCE).
2Click Prepare CCE.
3From the Password Setting drop down list, select Change Password. Keep the same passwords for the Edge Server, CCE Service and CA Backup File, but change the passwords for Tenant Account User and Tenant Account Password.
42

On Remote desktop, start the Sonus Cloud Link Deployer, and check Transfer Password from SBC to reset the credentials.