...
The
hardware platform comes equipped with four media ports and is available in three models based on the media port configuration. Customers must purchase the appropriate model based on their interface and capacity requirements. The media ports are enabled on the chassis depending upon the network interface license installed.| Caption |
|---|
| 0 | Table |
|---|
| 1 | SBC 5400 Interface Modes and Media Port Assignments |
|---|
| 3 | SBC 5400 Interface Modes and Media Port Assignments |
|---|
|
| Interface Mode | Port Assignments
(Active Media Ports) | SFP Types | License Required |
|---|
| 2 x 10 Gb | 0, 1 | 10 Gb SFP in Media Port 0 and Media Port 2 | SBC-1 X 10 GMP | | 2 x 1 Gb | 0, 1 | 1 Gb SFPs in Media Port 0 and 1 | None. Enabled by default | | 4 x 1 Gb | 0, 1, 2, 3 | 1 Gb SFPs in all four media ports | SBC-4 X 1 GMP |
|
| Caption |
|---|
| 0 | Table |
|---|
| 1 | Media Ports Speed and Descriptions |
|---|
|
| Media Port Speed | Description |
|---|
| 10 Gbps | In 2 x 10 Gbps mode:
| | 1 Gbps | In 4 x 1 Gbps mode: - Media 0, Media 1, Media 2, and Media 3 run at 1 Gbps and all the four ports are configurable.
- Pkt2 and Pkt3 ports do not operate without the 4 x1 Gbps license.
Media 0 socket maps to pkt0, Media1 socket maps to pkt1, Media2 socket maps to pkt2, and Media 3 socket maps to pkt3.
In 2 x 1 Gbps mode: - Media 0 and Media 1 run at 1 Gbps.
- Media 2 and Media 3 are inactive.
- Media 0 socket maps to pkt0, Media1 socket maps to pkt1, Media 2 socket maps to pk2, and Media 3 socket maps to pkt3.
|
|
| Info |
|---|
|
- The 2 x 10 Gbps flavor of the SBC 5400 does not support full-bandwidth DoS protection on both the packet ports.
- On a 2 x 10 Gbps flavor of the SBC 5400, the two 10 GE packet ports do not support an active-standby port redundancy model with each other. Both the ports are active when enabled on an Active SBC node, and both the ports are standby on a Standby SBC node.
- A single SBC-1 X 10 GMP packet port license is used to enable both 10 GE packet ports on an SBC 5400 in 10 Gbps mode.
|
| Info |
|---|
|
- The 2 x 1 Gbps mode is a default mode that any SBC 5400 platform can use. A license is required to use both 4 x 1 Gbps and 2 x 10 Gbps modes.
- If there is no license, only ports 0 and 1 are operable.
|
Media port speed is user-configurable. The following licenses support the media port configurations:
- SBC-4 X 1 GMP – This license allows four 1 Gbps media ports.
- SBC-1 X 10GMP – This license allows two 10 Gbps media ports.
...
...
...
...
Licensing for licensing details. |
Customers may upgrade or change the licensed network interfaces on their
systems after initial purchase as below, as needed.| Caption |
|---|
| 0 | Table |
|---|
| 1 | SBC 5400 Network Interface Upgrade Options |
|---|
| 3 | SBC 5400 Network Interface Upgrade Options |
|---|
|
| From | To |
|---|
| 2 x 1 Gb | 4 x 1 Gb | | 2 x 1 Gb | 2 x 10 Gb | | 4 x 1 Gb | 2 x 10 Gb | | 2 x 10 Gb | 4 x 1 Gb |
|
...
|
|---|
|
A media port operating in 10 GbE mode supports 10 Gb/s speed, full-duplex only and auto-negotiations is unsupported in this mode. Media ports operating in 1 GbE mode supports operation at 1 Gb/s speed, full duplex mode only with auto-negotiation enabled. |
10 GbE Mode
| Code Block |
|---|
[root@CHIVAS linuxadmin]# ethtool pkt0
Settings for pkt0:
Supported ports: [ FIBRE ]
Supported link modes: Not reported
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Link detected: yes |
| Code Block |
|---|
[root@CHIVAS linuxadmin]# ethtool pkt1
Settings for pkt1:
Supported ports: [ FIBRE ]
Supported link modes: Not reported
Supported pause frame use: Symmetric
Supports auto-negotiation: No
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Speed: 10000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
Link detected: yes |
1 GbE Mode
| Code Block |
|---|
[root@YF39 ~]# ethtool pkt0
Settings for pkt0:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Link detected: yes
[root@YF39 ~]# ethtool pkt1
Settings for pkt1:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Link detected: yes
[root@YF39 ~]# ethtool pkt2
Settings for pkt2:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Link detected: yes
[root@YF39 ~]# ethtool pkt3
Settings for pkt3:
Supported ports: [ FIBRE ]
Supported link modes: 1000baseT/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Advertised link modes: 1000baseT/Full
Advertised pause frame use: Symmetric Receive-only
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: FIBRE
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Link detected: yes
[root@YF39 ~]# |
| Warning |
|---|
|
Any changes to the media port speed, deletes the existing configuration. To use the option, Enable 10G Media Speed, power off the host first. |