Page History

Name

The packet service profile entry ID used to identify a particular packet service profile entry.

Silence Factor

The silence factor is the percentage of call time for which silence is expected. It is used to reduce expected call bandwidth.

The default value is 40.

Type of Service

Specifies the type of service (TOS) parameter to be provided in the IP header for voice packets. It is the decimal number that is included as is in the 8-bit TOS field of the IP header. Note that this number should be four times the DSCP value that you want to set in the high order 6 bits of the 8-bit TOS field.

The default value is 0.

Voice Initial Playout Buffer Delay

Specifies a numeric value, in milliseconds (ms), for the voice initial playout buffer delay required to absorb the maximum expected packet jitter across the network, in the range of 1 ms to 50 ms in increments of 1 ms.

The default value is 10 ms.

Peer Absence Action

Specifies the action to be taken when loss of bearer plane connectivity is detected on the channel. Possible actions are: • None—No

• None—No action taken.

• Trap—Generate an SNMP trap.

• Trap and

• Disconnect—Generate an SNMP trap and disconnect the call.

Requires the RTCP check box to be selected, which enables RTCP on the channel. The default setting is None.

AaL1 Payload Size

Specifies the ATM Adaption Layer Type 1 (AAL-1) payload size. For G.711, the possible values are 40, 44, or 47 bytes.
The default value is 47 bytes.

Preferred RTP Payload Type for DTMF Relay

Specifies the preferred RTP payload type in the RTP header of audio packets for this encoding. (default = 128). This parameter is only used for 8 kHz clock rate. DTMF payload type of each subsequent clock rate (16 kHz, 24 kHz, etc.) is incremented by 1.

Media Packet COS

Applies a Class of Service (COS) marking to be set in the User Priority field of the Ethernet VLAN tag header on media packets transmitted on a call leg that uses this packet service profile. Has an effect only if the network interface supports 802.1Q tagged Ethernet frames. The default value zero corresponds to best effort. The value range is 0-7.

Media Packet COS

Applies a Class of Service (COS) marking to be set in the User Priority field of the Ethernet VLAN tag header on media packets transmitted on a call leg that uses this packet service profile. Has an effect only if the network interface supports 802.1Q tagged Ethernet frames. The default value zero corresponds to best effort. The value range is 0-7.

Honor Remote Precedence

Specifies whether the audio encoding priority order of the local packet service profile takes precedence over the remote peer's audio encoding priority order when creating the priority order of the audio encodings that are common to both.

Possible choices are:

• Disabled (default) — the local audio encoding priority order take precedence. Disabled also makes the local secure RTP/RTCP settings and crypto suite priority order take precedence.
• Enabled — the remote peer's audio encoding priority order take precedence. For ingress call legs, Enabled also makes the remote peer's secure RTP/RTCP settings and crypto suite priority order take precedence

Honor Remote Precedence

Specifies whether the audio encoding priority order of the local packet service profile takes precedence over the remote peer's audio encoding priority order when creating the priority order of the audio encodings that are common to both.

• .

Send Route PSPPrecedence

Specifies the audio encoding order preference in outgoing messages only.
• disabled—When selected, Disable The options are:

• Disabled (default) —disable the audio encoding order preference.

• Enabled — enable the audio encoding order preference.

The RTP Payload Type included in the RTP header of the data packet. The value ranges from 0 to 127 and the default value is 56.

Specifies the maximum data packet size (Kilobits). The options are:

• 10
• 20
• 30
  
• 40

Specifies whether to enable RTCP. The options are:

• Disable (default)
• Enable – RTCP is used for the call.

• Disable (default) — RTCP is relayed between the endpoints for pass-through calls.
   
• Enable — Enable this option (as well as the Rtcp option) on one leg to terminate RTCP sessions on each leg for pass-through calls. If RTCP and RTCP termination is enabled on one leg of a pass-through call, RTCP is terminated and originated for that leg. If RTCP is enabled on both legs on the pass-through call, irrespective of Termination For Passthrough settings, RTCP is always relayed.
  
  

If this option is enabled, the SBC ignores the configured RR/RS values in the Packet Service Profile and send RR/RS = 0 in the offer/answer and disables RTCP when the call is active. When the call is HELD, and a RE-INVITE is sent, the SBC uses the configured values in the Packet Service Profile for RTCP bandwidth and enables RTCP. When the call is RESUMED, the SBC again disables RTCP by sending RR/RS=0 in the RE-INVITE.

The value of RR ranges from 100-4000 and the value of RS ranges from 100-3000.

If this flag is disabled, the older behavior of SBC is applicable.

The options are:

• Disabled (default)
• Enabled


Enter a value of 0, or a value in the range of 400-32767 to specify the Packet Loss Threshold (number of lost packets/100,000) which will trigger a Packet Loss Action. This parameter is required if RTCP is enabled. When set to “0”, no packet loss inactivity detection is performed. The default value is 0. 

This setting can be used in conjunction with Media Peer Inactivity. To set amedia peer inactivity timeout value, see the Media Peer Inactivity parameter on the Media Peer Inactivity page.

For an example configuration of this parameter, see the Packet Service Profile (CLI) page.

Specifies the RTCP bandwidth allocated to active data senders. The value ranges from 100 to 4000 and the default value is 250.

Specifies the RTCP bandwidth allocated for receivers. The value ranges from 100 to 3000 and the default value is 250.

• None — Take no action.
• Packet Loss Trap — Generate trap.

• Packet Loss Trap And Disconnect — Generate trap and disconnect.

By default, this option is enabled to allow SID packets to be sent within a minimal interval during a silence period (at least one SID packet must be sent within a SID maximum packet time frame). The options are:

• Disable
• Enable (default)

Defines the codec entry priorities and codec names. Up to 12 codec configurations are supported by the SBC in PSX and Advanced ERE deployment scenarios (see Routing and Policy Management for a description of the different routing configurations).

This attribute specifies the codec entry with a priority of "1". For each codec entry, select the desired codec. Codec IDs available by default are:

• G711-DEFAULT
• G711SS-DEFAULT
• G723-DEFAULT
• G723A-DEFAULT
• G726-DEFAULT
• G729A-DEFAULT
• G729AB-DEFAULT

 Transcode options:

• Conditional (default)
• Determined By Psp For Other Leg
• Only
• Transcoder Free Transparency



 Apply fax tone treatment. The options are:

• Disable (default)
• Enable

Enable this flag to perform transcoding when the ingress and egress call legs use different DTMF relay methods. The options are:

• Disable (default)
• Enable

 Enable this flag to perform transcoding when the ingress and egress call legs use different packet sizes. The options are:

• Disable (default)
• Enable

Enable this flag to perform transcoding when the ingress and egress call legs use different silence suppression methods. The options are:

• Disable (default)
• Enable

Enable Honor Offer Preference (HOP) to honor the codec preference of the peer's offer when Honor Remote Preference on the PSX is enabled.  This option is available only when Transcode is Conditional. (See the table below describing SBC behavior when this option is enabled/disabled). The options are:

• Disable (default)
• Enable

The SBC triggers a new offer towards the other side when an answer is received for a re-INVITE from this side. The re-INVITE generated on the other side carries all possible codecs in Route Packet Service Profile that causes the most preferred codec of the other side peer to be modified. Enable Honor Answer Preference (HAP) to lock down the most preferred codec towards the peer irrespective of re-INVITE received for mid-call modification from this side. (See the table below describing SBC behavior when this option is enabled/disabled). The options are:

• Disable (default)
• Enable

Enable this option to disallow data calls. The options are:

• Disable (default)
• Enable

Specifies whether digit detection is enabled on digits sent to the network. The options are:

• Disable (default)
• Enable

INFO: See Digit Detect Send Enabled Settings for KPML table below to understand which PSP leg to enable this flag for the desired KPML functionality.

Enable this option to use direct media as needed. The options are:

• Disable (default)
• Enable

Enable this option to validate peer support for DTMF events. Enable this option for all peer devices that support RFC 4733. The options are:

• Disable (default) – 

  Spacevars
  0 product

  does not validate the presence of DTMF events in the offer or answer from the peer. If DTMF relay is enabled, 

  Spacevars
  0 product

  transmits DTMF digits received from the other leg to this peer using the named event RTP payload.
• Enable – 

  Spacevars
  0 product

  validates the presence of DTMF events in the offer or answer from peers that support RFC 4733. If DTMF Relay is enabled and events 0-15 are received (with no other combination or subset of events), 

  Spacevars
  0 product

  forwards the events in the egress leg to this peer using the named event RTP payload. When 

  Spacevars
  0 product

  is configured for a pass-through call and it receives DTMF events other than 0-15 from the ingress peer, it does not offer any DTMF events to the egress endpoint.

Enable this option to interwork DTMF with out-of-band RFC2833 without using transcoding. The options are:

• Disable (default)
• Enable


When enabled on both the Ingress and Egress call leg, the DSCP value in the IP header of the media packets is transparently passed through the system. Once media is received from the peer, any value set in the Type Of Service field on the Packet Service Profile has no effect when Dscp Passthrough is configured on both legs for the associated call. The options are:

• Disable (default)
• Enable

Enable flag to generate a new SSRC (using a random value) along with a new timestamp on a new RTP stream whenever a resource is reactivated (due to change in codec, etc.). SSRC randomization reduces the probability of collision in large groups and simplifies the process of group sampling that depends on uniform distribution of SSRCs. The options are:

• Disable (default)
• Enable
  

Enable flag to set HD codecs as preferred codec over non-HD codecs even if transcoding is required. When flag is disabled, continue with existing PSP/IPSP behavior. The options are:

• Disable (default)
• Enable

When enabled,

Note:

• If Force Route PSPOrder is enabled, this option does not affect the ordering of outgoing offer.
• If Transcoder Free Transparency is enabled, this option is ignored.

Enable this option to allow the SBC to choose NB-NB pass-through over HD-HD transcoded call. The options are:

• Disable (default)
• Enable

When disabled, the SBC prefers HD-HD transcoded call over NB-NB pass-thru.

Note:

• This option is valid only if HDCodec Preferred is enabled, and it is applied when selecting a codec from answer.
• If Transcoder Free Transparency is enabled, this option is ignored.

Enable this option to allow the SBC to send only NB in the outgoing offer if only NB is received in the ingress offer. Otherwise, do nothing. While sending the offer, this option is ignored if either HD-only or (HD+NB) is received in incoming offer. The options are:

• Disable (default)
• Enable

If  this option is disabled, the SBC uses existing behavior.

Note: If Transcoder Free Transparency is enabled, this option is ignored.

Enable this option to send the outgoing offer in the same order as in the egress route Packet Service Profile, irrespective of HD/NB priorities. The options are:

• Disable (default)
• Enable

Note:

• If this flag is enabled, the HDCodec Preferred option does not affect the ordering of outgoing offer.
• If Transcoder Free Transparency is enabled, this option is ignored.

Reserves bandwidth on the basis of the preferred common codec, and polices on the worst case codec. This applies to both known and unknown codecs. The options are:

• Disable (default)
• Enable
  

Note: This option is active for a call when both PSPs have this option enabled. If this option is disabled in either of the PSPs, the option is not applied.

When enabled, the SBC reserves bandwidth based on the worst-case common codec on trunk groups and interfaces, but polices on the maximum bandwidth for all codecs from the Offer or Answer in a pass-through call. The options are:

• Disable (default)
• Enable
  

Note: This configuration applies to all pass-through calls. It works independently from Audio Transparency feature and Reserve BW For Preferred Audio Common Codec flag.

Specifies whether text media calls, using T.140 codec, are allowed. The options are:

• Disable (default)
• Enable

For more information on text codecs, refer to Text Codecs.

• Disable (default)
• Enable

Name

The packet service profile entry ID used to identify a particular packet service profile entry.

Silence Factor

The silence factor is the percentage of call time for which silence is expected. It is used to reduce expected call bandwidth.

The default value is 40.

Type of Service

Specifies the type of service (TOS) parameter to be provided in the IP header for voice packets. It is the decimal number that is included as is in the 8-bit TOS field of the IP header. Note that this number should be four times the DSCP value that you want to set in the high order 6 bits of the 8-bit TOS field.

The default value is 0.

Voice Initial Playout Buffer Delay

Specifies a numeric value, in milliseconds (ms), for the voice initial playout buffer delay required to absorb the maximum expected packet jitter across the network, in the range of 1 ms to 50 ms in increments of 1 ms.

The default value is 10 ms.

Peer Absence Action

AaL1 Payload Size

Specifies the ATM Adaption Layer Type 1 (AAL-1) payload size. For G.711, the possible values are 40, 44, or 47 bytes.
The default value is 47 bytes.

Preferred RTP Payload Type for DTMF Relay

Specifies the preferred RTP payload type in the RTP header of audio packets for this encoding. (default = 128). This parameter is only used for 8 kHz clock rate. DTMF payload type of each subsequent clock rate (16 kHz, 24 kHz, etc.) is incremented by 1.

Media Packet COS

Applies a Class of Service (COS) marking to be set in the User Priority field of the Ethernet VLAN tag header on media packets transmitted on a call leg that uses this packet service profile. Has an effect only if the network interface supports 802.1Q tagged Ethernet frames. The default value zero corresponds to best effort. The value range is 0-7.

Honor Remote Precedence

Specifies whether the audio encoding priority order of the local packet service profile takes precedence over the remote peer's audio encoding priority order when creating the priority order of the audio encodings that are common to both.

Possible choices are:

• disabled—When selected, Disabled makes the local audio encoding priority order take precedence. Disabled also makes the local Secure RTP/RTCP settings and crypto suite priority order take precedence.
• enabled—When selected, Enabled makes the remote peer's audio encoding priority order take precedence. For ingress call legs, Enabled also makes the remote peer's Secure RTP/RTCP settings and crypto suite priority order take precedence. The default setting is Disabled.

Send Route PSPPrecedence

Specifies the audio encoding order preference in outgoing messages only. The options are:

• disabled—When selected, Disable the audio encoding order preference.
• enabled—When selected, Enable the audio encoding order preference.

The RTP Payload Type included in the RTP header of the data packet. The value ranges from 0 to 127 and the default value is 56.

Specifies the maximum data packet size (Kilobits). The options are:

• 10
• 20
• 30

• 40

Specifies if the Rtcp option should be enabled or not. The options are:

• disable (default)
• enable – RTCP is used for the call.