Parameter | Description |
|---|
Name | The name of the ISUP signaling group you are configuring. This name must match the strings to be used in the version field of the SIP message header. |
Version Id | The version ID to identify a signaling group. Enter a value in the range of
(100..65535). | Info |
|---|
| Version IDs from 0-99 are reserved |
|
Base Profile | May be specified when configuring a named ISUP signaling profile. The specified base profile is used as a set of defaults for all profile parameter values. Then any parameter for which you explicitly specify a value overrides the default base profile value, in the resulting named signaling profile. |
OLIP Check | Specifies whether or not to support check for the presence of an OLIP when determining that a call is invalid. The options are: - Un Supported (default)
- Supported
|
Hop Count
Value | The initial Hop Counter value to use (if Hop Count State is enabled). Must be 10-20. |
Hop Count
State | The state of Hop Counting procedures for this service group: - Un Supported - (default) The procedures are in effect. This state requires that the ISUP protocol revision be ANSI1992 or ANSI1995.
- Supported - The procedures are not in effect.
When Hop Count State is enabled, the following applies: - If a Hop Counter parameter is received from the ingress leg of the call, it is decremented and included in the outgoing IAM message. If no Hop Counter is present in the ingress leg of the call, it is included in the outgoing IAM message using Hop Count Value.
- If a Hop Counter of zero is present in the ingress leg of the call, the call is released with a cause of "exchange routing error".
When Hop Count State is disabled, the following applies: - If a Hop Counter parameter is received from the ingress leg of the call, it is passed transparently in the outgoing IAM message.
- If a Hop Counter of value zero is present in the ingress leg of the call, the call is released with a cause of "exchange routing error".
|
Base Version | Specifies the version of the Base Signaling group from rfc3204. The possible values are: - Ansi00
- Ansi88
- Etsi121
- Etsi356
- Gr317
- Itut-88
- Itu-t92+
- None
- Ttc87
- Ttc93+
|
Revision | The ISUP protocol revision that will be supported for this ISUP service: - Ansi1992 - Use this protocol if this ISUP service is connecting DMS and ESS SWITCHTYPEs.
- Ansi1995
- Itu1993
- Etsi2 - Use for Germany and Netherlands. (For Germany, use the Default_German ISUP signaling profile; for Netherlands, use the Default_ETSI_V2 ISUP signaling profile.)
- Nttfcc - Use for Japan.
- Itu1997
- Itu1988
- Ituq767 - Same as etsii (has been renamed).
- Belgacom
- Spirou
- Mexicoic
- Italy
- Denmarkic
- Hongkongic
- Singapore
- Etsi3
- Peru
- Chile
- Portugaloni
- Nttcom - Use the NTT Communications protocol for Japan.
- Chinacnc
- Spain
- Argentinaidt
- Argentina
- Brazil
- India
- Korea
- Ukisup
- Etsi2plus - Use for Malaysia.
- Ansiatt
- Israel
- Slovak2 - Use for Slovakia
- Russia
|
OLIP Check on
Send | When a call with a Charge Number and a Calling Party Number arrives, by default the checks for Originating Line Information Parameters (OLIP) and rejects the call if they are not present. This parameter turns OLIP checking off for certain switches that do not supply OLIP information to such calls: • unsupported—check for OLIP • supported —don't check for OLIP This check is applied only when the receives an IAM. |
Network
Indicator | Specifies whether the network indicator functionality is active. |
Propogation
Delay Support | Specifies whether the propagation delay functionality is active: - Un Supported (default)
- Supported
|
Look Ahead for
Busy | Specifies the default value used in the Look Ahead for Busy field in the ISUP Precedence parameter.
• allowed—Look Ahead for Busy is allowed.
• path reserved—Look Ahead for Busy path is reserved.
• not allowed (default)—Look Ahead for Busy is not allowed. |
Network
Identity | Specifies the default value used for the 4-digit network identity field in the ISUP Precedence parameter. Must be 0000-9999; default is 0100. |
Generate Japan
Ics Params | Specifies whether to support generating ICS information in SIP MIME case for the signalling group. |
Compatibility | Specifies whether the compatibility is supported for the ISUP Signaling profile |
Access
Delivery | Specifies whether the access delivery information is active. |
Generic Number | Specifies whether the generic number functionality is active: - Un Supported (default)
- Supported
|
Generic
Notification | Specifies whether the generic notification functionality is active: - Un Supported (default)
- Supported
|
Generic Digits | Specifies whether the generic digit functionality is active: - Un Supported (default)
- Supported
|
Location
Number | Specifies whether the location number functionality is active: - Un Supported (default)
- Supported
|
Originating
ISC Point Code | Specifies whether the originating ISC point code functionality is active: - Un Supported (default)
- Supported
|
User Tele
Service | Specifies whether the user teleservice functionality is active: - Un Supported (default)
- Supported
|
Segmentation | Specifies whether the segmentation functionality is active: - Un Supported (default)
- Supported
|
Fallback | Specifies whether the fallback functionality is active: - Un Supported (default)
- Supported
|
E MCID | Specifies whether the EMCID functionality is active: - Un Supported (default)
- Supported
|
Subscriber
Priority Class | Specifies whether the subscriber priority class functionality is active: - Un Supported (default)
- Supported
|
APM | Specifies whether the APM is supported for the ISUP Signaling profile. - Un Supported (default)
- Supported
|
Connected
Number in ACM | Specifies if the connected number parameter is supported in the ACM for the ISUP Signaling profile. |
Cause In CPG | Indicates that the cause parameter supported in the CPG for the ISUP Signaling profile. |
Multi Carrier
Environment | Specifies whether the multi carrier environment functionality is active. |
Carrier
Selection | Indicates that the carrier selection is supported for the ISUP Signaling profile. |
Inr Inf | Specifies whether INR/INF messages are supported. |
CQM CQR | Specifies if the CQM/CQR is supported for the ISUP Signaling profile. |
Call Reference | Indicates that the call reference parameter is supported for the ISUP Signaling profile. |
CFN | Indicates that the CFN is supported for the ISUP Signaling profile. |
Facility | Specifies whether the FAA, FAR, and FRJ messages are supported. |
PAM | Specifies whether the PAM message is supported. |
OBCI ANM | Specifies whether the optional backward call indicators parameter is supported in the
ANM message. |
DRS | Specifies whether the DRS message is supported. |
Redirection
Number | Specifies whether the redirection number parameter is supported. |
LPA | Specifies whether the LPA message is supported. |
UCIC | Specifies whether the UCIC message is supported. |
OLM | Specifies whether the OLM message is supported. |
Blue Book In
Rel | Specifies whether the Blue Book parameters are supported in REL for the ISUP Signaling Profile. |
USR | Specifies whether the Blue Book specific parameters are supported in the USR
message |
BB IAM | Specifies whether the User-To-User indicator parameter is supported in IAM for the
ISUP Signaling Profile. |
Call Mod Msgs | Specifies that the CMR, CMA and CMRJ are the call mod messages supported for the ISUP Signaling profile. |
Call Diversion | Specifies whether the call diversion is supported for the ISUP Signaling profile. |
Call History | Specifies whether the call history parameter is supported for the ISUP Signaling profile. |
Generic
Reference | Specifies whether the generic reference parameter is supported |
MLPP | Specifies whether the MLPP parameter is supported. |
NSF | Specifies whether the network specific functionality parameter is supported. |
Redirection Number Restriction | Specifies whether the redirection number restriction parameter is supported in ANM, ACM, CPG, and CON messages |
Remote
Operations | Specifies whether the remote operations parameter is supported. |
Service
Activation | Specifies whether the service activation parameter is supported. |
Signaling
Point Code | Specifies whether the signaling point code parameter is supported. |
TMR Prime | Specifies whether the transmission medium required prime parameter is supported. |
Transmission
Medium Used | Specifies whether the transmission medium used parameter is supported. |
USI Prime | Specifies whether the user service information prime parameter is supported. |
Redirection
Number in ACM | Is the redirection number supported in the ACM for the ISUP Signaling Profile. |
Redirection
Number in ANM | Is the redirection number supported in the ANM for the ISUP Signaling Profile. |
Connection Req in FAA | Specifies whether the connection request parameter is supported in the FAA for the
ISUP Signaling profile. |
Connection Req in FAR | Specifies whether the connection request parameter is supported in the FAR for the
ISUP Signaling profile. |
FAC | Specifies whether the FAC message is supported |
Echo Control | Specifies whether the echo control parameter is support. |
Backward GVNS | Specifies whether the backward GVNS parameter is supported for the ISUP Signaling Profile. |
Circuit
Assignment Map | Specifies whether the circuit assignment map parameter is supported for the ISUP Signaling profile. |
CCSS | Indicates that the CCSS parameter supported for the ISUP Signaling profile. |
Call Diversion
Treatment | Specifies whether the call diversion treatment parameter is supported for the ISUP Signaling profile. |
Called In Num | Indicates that the called IN number parameter supported for the ISUP Signaling profile. |
Collect Call
Req | Specifies that the collect call request parameter is supported for the ISUP Signaling profile. |
Conference
Treatment | Specifies whether the conference treatment parameter is supported for the ISUP Signaling profile. |
Correlation Id | Specifies whether the correlation ID parameter supported for the ISUP Signaling profile. |
Call Offering
Treatment | Indicates that the call offering treatment parameter is supported for the ISUP Signaling profile. |
Call Transfer
Number | Indicates that the call transfer number parameter is supported for the ISUP Signaling profile. |
Call Transfer reference | Indicates that the call transfer reference parameter is supported for the ISUP Signaling profile. |
Display Information | Indicates that the display information parameter is supported for the ISUP Signaling profile. |
Forward GVNS | Specifies whether the forward GVNS parameter is supported. |
Loop
Prevention | Specifies whether the LOP message and the Loop Prevention indicators parameter is supported. |
Network
Management | Specifies whether the Network Management Control parameter is supported. |
SCF Id | Specifies whether the SCF ID parameter is supported. |
UID Action IND | Specifies whether the UID action indicators parameter is supported. |
Uid Capability
Ind | Specifies the UID capabilities parameter supported for the ISUP Signaling Profile. |
Connected
Number In Cpg | Specifies the connected number parameter supported in the CPG for the ISUP Signaling
Profile. |
Generic Number
In Cpg | Specifies the generic number parameter supported in the CPG for the ISUP Signaling Profile. |
Echo Control
In Iam | Specifies the echo control parameter supported in the IAM for the ISUP Signaling
Profile. |
Remote Operation In Rel | Specifies the remote operations parameter supported in the REL for the ISUP Signaling Profile. |
Access Transport In Fac | Specifies the access transport parameter supported in the FAC for the ISUP Signaling Profile. |
Generic Notification In Fa | Specifies the generic notification parameter supported for the ISUP Signaling Profile. |
Uuind Anm | Specifies the UUI parameter supported in the ANM for the ISUP Signaling Profile. |
Uuind Cpg | Specifies the UUI parameter supported in the CPG for the ISUP Signaling Profile. |
Nrm Support | Specifies the NRM supported for the ISUP Signaling Profile. |
Cause In Rlc | Specifies the cause parameter supported in the RLC for the ISUP Signaling Profile. |
Upa Upt | Specifies the UPA/UPT supported for the ISUP Signaling Profile. |
Recommendation
In Cai | Specifies the recommendation field supported in the cause parameter for the ISUP Signaling Profile. |
Transit
Unrecognized | Specifies the transiting of unrecognized parameters supported for the ISUP service
Group. |
U2u Service
Level | Specifies the level of user to user services supported in the ISUP Signaling Profile. |
Subsequent Address Message | Specifies the Subsequent Address Message supported for the ISUP Signaling
Profile. |
Forward Transfer Message | Specifies the Forward Transfer Message supported for the ISUP Signaling Profile. |
Special Digits | Specifies the special digits which can appear in dialed digit strings
• digitA - BIT 0 - Is digit A allowed in the digit string
• digitB - BIT 1 - Is digit B allowed in the digit string(default)
• digitC - BIT 2 - Is digit C allowed in the digit string(default)
• digitD - BIT 3 - Is digit D allowed in the digit string
• digitE - BIT 4 - Is digit E allowed in the digit string
• digitF - BIT 5 - Is digit F allowed in the digit string(default)
• none - BIT 6 - No special digits in the digit string |
Transit Network Selection | Specifies the Transit Network Selection Parameter supported for the ISUP Signaling
Profile. |
Access
Transport | Specifies the Access Transport parameter supported for the ISUP Signaling Profile. |
Jurisdiction | Specifies the Jurisdiction parameter supported for the ISUP Signaling Profile. |
Original Called Number | Specifies the Original Called Number parameter supported for the ISUP Signaling Profile. |
Business Group | Specifies the Business Group parameter supported for the ISUP Signaling Profile. |
Connection Req | Specifies the Connection Request parameter supported for the ISUP Signaling Profile. |
Information Ind | Specifies the Information Indicator parameter supported for the ISUP Signaling Profile. |
Network Transport | Specifies the Network Transport supported for the ISUP Signaling Profile. |
Notification Ind | Specifies the Notification Indicator parameter supported for the ISUP Signaling Profile. |
Redirection Info Acm | Specifies the Redirection Information parameter supported in the ACM message for the ISUP Signaling Profile. |
Egress Service | Specifies the Egress Service parameter supported for the ISUP Signaling Profile. |
Service Code Ind | Specifies the Service Code Indicator parameter supported for the ISUP Signaling Profile. |
Special Process Req | Specifies the Special Processing Request parameter supported for the ISUP Signaling Profile. |
Charge Number | Specifies the Charge Number parameter supported for the ISUP Signaling Profile. |
Transaction Req | Specifies the Transaction Request parameter supported for the ISUP Signaling
Profile. |
Generic Address Rel | Specifies the Generic Address parameter supported in the REL message for the
ISUP Signaling Profile. |
Uu Ind Acm | Specifies the User to User Indicators parameter supported for the ISUP Signaling
Profile. |
Uu Info | Specifies the User to User Information parameter supported for the ISUP Signaling
Profile. |
Operator
Service Info | Specifies the Operator Service Information parameter supported for the ISUP Signaling Profile. |
Cvt Cvr | Specifies the Circuit Validation Test/Response procedures supported for the ISUP Signaling Profile. |
Generic Name | Specifies the Generic Name parameter supported for the ISUP Signaling Profile. |
Redirection
Cap | Specifies the Redirection Capability parameter supported for the ISUP Signaling
Profile. |
Group Redirection Count | Specifies the Group Redirection Count parameter supported for the ISUP Signaling
Profile. |
Send Two Group Msgs | Sets the Flag to Send Two Group Messages in the ISUP Signaling Profile. |
Await Two Group Msgs | Sets the Flag to Await Two Group Messages in the ISUP Signaling Profile. |
Cqm On Card Swap | Sets the Flag to perform CQM on Card Swap in the ISUP Signaling Profile. |
Ansi95Grs | Specifies the ANSI-95 format for Group Reset Circuit (GRS), which includes optional/ parameters to be used. |
Cpg Before Acm | Specifies a CPG arriving before an ACM be transited. |
Map Dms Fe Parameter | Specifies if the service group should perform mapping of the Completion Code in the DMS FE parameter (ANSI ISUP only) |
Trunk Offering Support | Specifies if the trunk offering messages can, fan, ofr, rcl are supported, at the moment this is just for mexico. |
Operator Selection | Specifies if the operator selection parameter is supported. |
Max Calling Party Digits | Specifies the maximum digit string length for the Calling Party Number parameter supported for this ISUP Signalling Profile. |
Max Called Party Digits | Specifies the maximum digit string length for the Called Party Number parameter supported for this ISUP Signalling Profile |
Free Phone Ind | Specifies the Freephone Indicators parameter supported for this ISUP Signalling Profile. |
Itx Txa | Specifies the ITX and TXA messages supported for the ISUP Signaling Profile. |
Sccp Procedure | Specifies the SCCP Procedure supported for the ISUP Signaling Profile. |
Connection Req In Iam | Specifies the Connection Request parameter supported in the IAM for the ISUP Signaling Profile. |
Ccnr | Specifies the CCNR Possible Indicator parameter supported for the ISUP Signaling Profile. |
Transit Cfn | Specifies the CFN message be transmitted for the ISUP Signaling Profile. |
Holding Ind | Specifies the Holding Indicator be supported for the ISUP Signaling Profile. |
Display Info In Acm | Displays Information parameter in the ACM be supported for the ISUP Signaling Profile |
IAM Generated Carrier Code In Cdr | Should the IAM-Generated Carrier Code always be populated in the CDR for Japan regardless of type. |
Cit Term Exchange Logic | CIT and CAI only in first backward message when terminating exchange |
Check Ixc Against Tlec | • PROTOCOLS - JAPAN
• DEFAULT- UNSUPPORTED
• UNSUPPORTED - Modify received CIT parameter as usual
• SUPPORTED - Transit received CIT parameter unchanged
• CMD- TRANSITRCVDCIT
• SCREEN- Services - Transit Received CIT
• CONTROL- SS7_CONTROL_TRANSIT_RECEIVED_CIT
• REQS- SBTM - PCR1499 |
Unique Transit Cit | • PROTOCOLS - JAPAN
• DEFAULT- UNSUPPORTED
• UNSUPPORTED - Modify received CIT parameter as usual
• SUPPORTED - Transit received CIT parameter unchanged
• CMD- TRANSITRCVDCIT
• SCREEN- Services - Transit Received CIT
• CONTROL- SS7_CONTROL_TRANSIT_RECEIVED_CIT
• REQS- SBTM - PCR1499 |
Transit Received Cit | • PROTOCOLS - JAPAN
• DEFAULT- UNSUPPORTED
• UNSUPPORTED - Modify received CIT parameter as usual
• SUPPORTED - Transit received CIT parameter unchanged
• CMD- TRANSITRCVDCIT
• SCREEN- Services - Transit Received CIT
• CONTROL- SS7_CONTROL_TRANSIT_RECEIVED_CIT
• REQS- SBTM - PCR1499 |
| Allow SGDin Generic Digits | Specifies whether SGD parameter (Generic Digits type 25) in mime of SIP-I message is supported or not. The options are: - Un Supported (default)
- Supported
| Info |
|---|
| If the SGD parameter in the SIP-I mime is to be processed or sent, the Generic Digits needs to be supported as well. |
| Info |
|---|
| This flag is not applicable when the SBC is configured for ERE mode. |
|
| Set Bci Cdps Based On Sip Call Status | Set this flag to "supported" to modify the called party's status indicator in BCI parameter of MIME data as per the SIP status. If 183 Session Progress is carrying a MIME of called party's status indicator in BCI with a value OTHER THAN "No indication", then it is updated to a value "No indication". Similarly, if 180 Ringing is carrying a MIME of called party's status indicator in BCI with a value OTHER THAN "Subscriber Free", then it is updated to a value "Subscriber Free". The options are: - Un Supported (default)
- Supported
|
| Send PRIon RELfor CBWF | Use this flag to send either APM or PRI message with Call Back When Free (CBWF) information on the SIP-I (UK-ISUP) leg during tear down of CBWF call. The options are: - Supported
: Send PRI message
- Un Supported (default): Send APM message
| Info |
|---|
| The flag Send PRIon RELfor CBWF applies to SIP-I (UK-ISUP variant) only. |
|
| Send APPin APMfor CBWF | Use this flag to send CBWF-related APP (ACI=126) in a new APM message. If set to "unsupported" , APP is sent in the regular signaling message (e.g. ACM instead of APM). The options are: - Supported: When this option is selected, only APM messages are sent with APP information.
- Un Supported (default): When this option is selected, the APP parameter is sent in regular signaling messages. For example, ACM instead of APM.
| Info |
|---|
| The flag Send APPin APMfor CBWF applies to SIP-I (UK-ISUP variant) only. |
|
| Gr317Charge Number Compliance | Use this flag to check the charge number digit length is in compliance with GR317 which specifies a maximum of 10 digits in IAM message. The Gr317Charge Number Compliance flag does not affect the charge number header contents in SIP messages. When the egress trunk group has the Isup Mime Body Relay flag enabled, any charge number parameter received in the ingress ISUP MIME is sent in the egress ISUP MIME irrespective of the value of Gr317Charge Number Compliance setting. - UnSupported (default) – SBC does not check charge number digit length for GR317 compliance.
- Supported – SBC checks charge number digit length for GR317 compliance, and does not send message if digit length is greater than 10 digits. If digit length is 11 or more digits, the charge number parameter is discarded and a MINOR log message is logged to the debug log.
| Info |
|---|
| This flag can only be set to Supported for ANSI ISUP variant. Additionally, the Gr317Charge Number Compliance check only applies to the ISUP MIME sent by the SBC; it does not apply to the ISUP MIME received by the SBC. |
|
| Charge Rate Info For CPC Apc | Use this flag to determine whether the SBC checks for specific payphone-related characteristics in J-ISUP to non-Japanese ISUP calls to trigger using different charge rate information (CRI). The options are: - Supported
- Un Supported (default)
If set to Supported, the SBC checks for the following conditions: - The ingress leg of the call must be a J-ISUP variant
- The egress leg of the call must be a non-Japanese ISUP variant
- The call request must include one of the following:
- The CPC (Calling Party's Category) value in the incoming INVITE/IAM message has the value "pay phone"
- The APC (Additional Party Category) value in the incoming INVITE/IAM message has the value "Pink" (00000010) or "train pay phone"(00000001).
If a call meets the conditions, the SBC takes charge rate information (CRI) taken from the PSX Charge Rate Profile table specified in the PSX Charge Band Profile associated with the call's ingress trunk group. The CRI is returned in the first backward Address Complete Message (ACM), Call Progress (CPG), or Charging Information (CHG) message during call setup. If the option is set to Supported but the conditions are not met or Charge Rate Profile table data is not available, no charge information is returned in the ACM, CPG, or CHG messages. If the option is set to Un Supported, the SBC takes CRI values from the PSX Charge Rate Information Parameter table for J-ISUP to non-Japanese ISUP calls and sends them in the first backward ACM, CPG, or CHG message during call setup. | Info |
|---|
| The Charge Rate Info For CPC Apc option is only configurable on Japan-based ISUP Signaling Profiles in which the Revision value specifies either the Nttfcc or Nttcom ISUP variant. |
|
| Cpg Release Timer | Use this timer to specify a time, in seconds, after which the SBC releases a call that has had ANM to CPG message conversion applied. The timer can be set up to 300 seconds. The default is 0. | Info |
|---|
| | Values greater than 0 can be configured only on JAPAN-based profiles in which the Revision value specifies either the Nttfcc or Nttcom ISUP variant. |
|
