Page History
...
Add_workflow_for_techpubs | ||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
|
Include Page
_SBC 5100 5200 Unsupported
...
_SBC 5100 5200 Unsupported
Use this window to configure
...
the Egress-specific
...
Call Admission Control (CAC) configuration for a specified SIP trunk group.
From the SBC main screen,
...
navigate to Configuration
...
→ System Provisioning
...
→ Category: Trunk Provisioning
...
→ Trunk Group
...
→ SIP Trunk Group
...
→ CAC →
...
Egress or
All →
...
Address Context →
...
Zone →
...
SIP Trunk Group
...
→ CAC →
...
Egress
Use the drop-down lists to select an Address Context, Zone
...
, and SIP Trunk Group.
...
SIP Trunk Group - Egress CAC Window
Include Page |
---|
...
|
...
|
Use the following table to configure and then click Save.
Parameter | Length/Range | Description |
---|---|---|
Call Rate Max | unlimited or SBC 5400/SWe: 1-450 SBC 7000/CNe: 1-1350 | Specifies the value of maximum allowed sustained calls/second for egress call attempts |
...
. |
...
...
The default value is unlimited. |
...
Note: You can set both Call Burst Max and Call Rate Max as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value. | ||
Call Burst Max | unlimited or SBC 5400/SWe: 1-900 SBC 7000/CNe: 1-2700 | Specifies the value of the maximum allowed burst (above the allowed sustained rate) for egress call attempts in calls/second. |
SBC 5400 /SWe - Range: 1-900, or unlimited. (The default value is unlimited.)
The default value is unlimited. |
...
Note: You can set both Call Burst Max and Call Rate Max as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value. | ||
Register Rate Max | unlimited or SBC 5400/SWe: 1-1500 SBC 7000: 1-3000 | Specifies the maximum allowed sustained egress rate (registrations per second) for initial SIP registrations |
...
. The default value is unlimited. Note: You can set both Register Burst Max and Register Rate Max as unlimited; however, if you assign a value to one parameter, the other must also be assigned a value. | ||
Register Burst Max | unlimited or SBC 5400/SWe: 1-1500 SBC 7000: 1-3000 | Specifies the maximum allowed egress burst (above the allowed sustained rate) for initial SIP registrations. |
...
The default value is unlimited. |
...
Call Limit | 0-2147483647 | Specifies the total number of concurrent calls (either ingress or egress) allowed on egress. The |
...
default is unlimited. | ||
Emergency Oversubscription | 0-1000 | Specifies the oversubscription of resources (as a percentage) that is allowed for emergency calls. The |
...
default value is 10. | ||
Extended Emergency IP Limit | 0-40000 | The resource oversubscription (expressed as a numeric value) allowed for emergency calls. The |
...
default value |
...
is 0. | ||
Subscribe Rate Max | unlimited or SBC 5400/SWe: 1-1000 SBC 7000: 1-3000 | Specifies the maximum sustained egress rate (subscribes per second) of the initial SIP subscribe request. |
...
The default value is unlimited. |
...
0 | series2 |
---|
...
Subscribe Burst Max | unlimited or SBC 5400/SWe: 1-1000 SBC 7000: 1-3000 |
...
...
Specifies the maximum allowed burst (above the allowed sustained rate) for egress initial SIP subscribe request. |
...
The default value is unlimited. |
...
0 | series2 |
---|
...
Other Req Rate Max
Other Req Rate Max | unlimited or SBC 5400/SWe: 1-1000 SBC 7000: 1-3000 |
Specifies the maximum sustained egress rate (requests per second) of other out-of-dialog SIP requests. |
...
The default value is unlimited. |
...
0 | series2 |
---|
...
Other Req Burst Max | unlimited or SBC 5400/SWe: 1-1000 SBC 7000: 1-3000 |
...
Specifies the maximum allowed burst (above the allowed sustained rate) for any other egress out-of-dialog SIP request. |
...
The default value is unlimited. |
...
Hpc Oversubscription | 0 |
...
-100 |
Specifies the over-subscription of the resources ( |
...
as a percentage) that is allowed for HPC calls. When the baseline call limit and bandwidth limits are reached, normal calls are not admitted, but additional HPC calls are allowed up to the configured value percentage. The |
...
default value is 10 |
...
. |