Overview
The
supports TCP (Transmission Control Protocol) for peering, enterprise, and access configurations.
In an Access scenario, connections are on a per-subscriber-registration basis. The
keeps track of subscriber-initiated TCP “flow” beginning with when the endpoint registers, and uses it to forward any requests to the subscriber. The connection stays up as long as the subscriber is registered with the
.
A connection is deleted when the flow cannot reach the subscriber (example a broken TCP connection), when the connection is replaced by a newer one through successful modification, or when the registration is deleted.
For Peering, there are typically two connections, one for each direction. Connections to the peers are maintained and reused for all requests to the peer, independent of calls. The
can accept multiple connections from the same remote peer.
The
also supports TCP Fallback. When enabled, the following functionality is available:
- Reject incoming INVITE over UDP with PDU size greater than allowed configured size if enabled on ingress Trunk Group. However, the same INVITE is supported by the , if it is received over TCP.
- Send out INVITE over TCP if outgoing INVITE size is more than the configured size enabled on the egress Trunk Group.
When TCP fallback feature is enabled it overrides any other configuration related to transport preference.
When a UE sends REGISTER request to the over a TCP connection and the registration is successful, the TCP connection is present between UE and SBC for the life of the registration. If the registration becomes inactive, the relies on the UE to clear (close) the TCP connection between the two.
The SIP Trunk Group flag clearTcpConnectionsforRegistration allows the to clear the TCP connection between the UE and once the registration becomes inactive. The closes the TCP connection even when there are user agent failure registrations.
TCP Keep-alive Timer
The
supports configuring TCP Keep-alive timer settings for SIP Trunk Group and Signaling Port configurations. These parameters enable the
to send out TCP Keep-alive packets to peer devices (for example, registered SIP phones) at configured intervals.
Examples
SIP Trunk Group Configuration
The following example sets the NAT keep-alive timer to 200 seconds for SIP over TCP.
| Code Block |
|---|
|
% set addressContext default zone ZONE_IAD sipTrunkGroup SBX10_IAD services natTraversal tcpKeepaliveTimer 200
% commit
% show addressContext default zone ZONE_IAD sipTrunkGroup SBX10_IAD services
natTraversal {
tcpKeepaliveTimer 200;
} |
For configuration details, refer to SIP Trunk Group - Services (EMA) or SIP Trunk Group - Services - CLI.
SIP Signaling Port Configuration
The following example sets tcpKeepaliveTime to 90 seconds, tcpKeepaliveInterval to 60 seconds and tcpKeepaliveProbes count to 2 for SIP Signaling Port 2:
| Code Block |
|---|
|
% set addressContext default zone ZONE_SIPART_AS sipSigPort 2 tcpKeepaliveTime 90 tcpKeepaliveInterval 60 tcpKeepaliveProbes 2
% commit
% show details addressContext default zone ZONE_SIPART_AS sipSigPort 2
ipInterfaceGroupName LIG2;
ipAddressV4 10.7.14.179;
portNumber 5060;
mode inService;
state enabled;
recorder disabled;
siprec disabled;
tcpConnectTimeout 5;
dscpValue 0;
tlsProfileName defaultTlsProfile;
transportProtocolsAllowed sip-tcp;
sctpProfileName defaultSctpProfile;
tcpKeepaliveTime 90;
tcpKeepaliveInterval 60;
tcpKeepaliveProbes 2; |
For configuration details, refer to Signaling Ports - SIP Sig Port (EMA) or Zone - SIP Sig Port - CLI.
The
supports the ability to specify a TCP port range for MSRP and BFCP (over TCP) streams using the configurable
TCP Port Range object. TCP port ranges are used by the
to advertise TCP ports on which it can accept connections. TCP port ranges can be configured at the system level and on the SIP trunk group level.
The two configurable fields/parameters under tcpPortRange for the system include:
baseServerPort – The starting (base) port number for the range of TCP ports to use for media. The allowed baseServerPort range is 1-65534, with a system default value of 1024.maxServerPort – The maximum TCP port number for the range of TCP ports to use for media. This value must be greater than the baseServerPort. The allowed maxServerPort range is 1-65534, with a system default value of 65534.
The two configurable fields/parameters under tcpPortRange for a SIP trunk group are similar:
baseServerPort – The starting (base) port number for the range of TCP ports to use for media for the trunk group. The allowed baseServerPort range is 1-65534, or "none." The default value is none which indicates the uses the baseServerPort value specified at the system level.maxServerPort – The maximum TCP port number for the range of TCP ports to use for media. This value must be greater than the baseServerPort. The maxServerPort range is 1-65534, or "none." The default value is none which indicates the uses the maxServerPort value specified at the system level.
Each SIP trunk group can include a mediaIpAddress to indicate which IP address to use when allocating TCP media. The default value is 0.0.0.0 indicating that the system will choose an IP address from the mediaIpInterfaceGroup. The mediaIpAddress can be configured as either an IPv4 or IPv6 address. Any media IP address configured must belong to the IP Interface Group configured as the mediaIpInterfaceGroup for the trunk group.
Use the CLI 'show table' command to view the ipInterfaceGroup table listing TCP (or UDP) port ranges that are in assigned (mediaPortRangeAssigned) or available (mediaPortRangeUnassigned) for the indicated IP Interface Group.
For configuration details, refer to: