Versions Compared

Old Version 1

changes.mady.by.user Menon, Sangeeta - deprovisionUser 05/27/2020

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.


Add_workflow_for_techpubs
AUTH1samenon
REV5ghoppe
REV6ghoppe
REV3akempanarasimhaiah
REV1aprakash

 

Panel

In this section:

Table of Contents
maxLevel2

...

The parameters to define the GW signaling port differ based on your type of the SBC platform. For cloud-based deployments of SBC SWe (I-SBC or D-SBC), the parameters include IP Var so that the IP address for the port can be specified using a metavariable rather than a static IP address. For other SBC platforms, use the IP Address V4 or V6 parameter appears for you to enter a specific IP address.

The SBC supports a single GW signaling port at a time. The GW signaling port must be defined within the "default" address context and the "defaultSigZone" zone, and it must be assigned an index value of 1. 

Include Page
Unique_IP_for_SigPort
Unique_IP_for_SigPort

...

On the SBC main screen, go to Configuration > System Provisioning > Category: Base Provisioning > Signaling Ports > GW Sig Port.

The GW Sig Port window is displayed. The following example figure shows the window for an I-SBC /or D-SBC output(cloud) deployment that includes the IP Var parameter.

Caption
0Figure
1Signaling Ports - Gw Sig Port with IP Address

...

 The following figure shows the window for non-cloud deployment that includes the IP Address V4 or V6 parameter.

Caption
0Figure
1Signaling Ports - Gw Sig Port with IP Address

Image Added

Create the GW Sig Port

To create a new GWSig GW Sig Port,

  1. Select

...

  1. default

...

  1. from the Address Context drop-down and 

...

  1. defaultSigZone

...

  1. from the Zone drop-down.
  2. Click the New GW Sig Port

...

  1. on the GW Sig Port List panel.
Caption
0Figure
1Gw Sig Port Fields

Image Removed

The Create New Gw Sig Port window is displayed. The following example shows the parameters for an I-SBC or D-SBC deployment.

Caption
0Figure
1Gw Sig Port Create Window

 


The following fields are displayed:

Caption
0Table
1Gw Sig Port Parameters


Parameter

Description

Index

Set the index for gateway signaling port to 1.

Ip Interface Group Name

Specify the name of the IP interface group used by this signaling port.

Ip Address

Specify the IP address for the gateway signaling listening port in IPV4 or IPV6 format.

This is a required parameter visible on hardware systems and SBC SWe systems that do not use metavariables.

Note: For cloud-based I-SBC, D-SBC SBC SWe deployments, this parameter is not visible.

Port Number

The logical port number of the TCP port to use for this connection. Must be 1-65535, default is 2569.

Role

The main role of the signaling port:
• primary(default)—the port that makes gateway signal link connection requests to other

Spacevars
0product
, using its IP address as the local address for listening.
• secondary—an alternate port that is used for listening only and cannot be used to establish new gateway signal links.

When no primary port exists, connection requests to other 
Spacevars
0product
cannot be issued and calls which require them are disconnected.
When a secondary port is configured to be primary, the previous primary is automatically made secondary.

Mode

The operational state of the Gateway signaling service:
• inService(default)—the signaling port listens for incoming gateway signal link connection requests.
• outofService—the signal port is not available for incoming gateway signal link connection requests and thus cannot be used to create a new gateway signal links to other

Spacevars
0product
.

State

The administrative state of this gateway signaling port:
• disabled—Not active
• enabled—Active

IP Var

Specify the metavariable to use to assign an IP address to the gateway signaling port in an I-SBC or D-SBC deployment. .

Note: This parameter is visible for only I-SBC and D-SBC deployments in the SBC SWe.


Edit the GW Sig Port

To edit any of the Gw Sig Ports in the list, click the radio button next to the specific Gw Sig Port name.

Caption
0Figure
1Gw Sig Port Highlighted

Image Removed

 

The Edit Selected GW Sig Port window showing the parameters for an I-SBC or D-SBC is displayed below.

Caption
0Figure
1Gw Sig Port Edit Window

Image Removed

 

...

  1. Click the radio button next to the name of the entry you want to edit. The Edit Gw Sig Port window opens.

  2. Change the variable value and click Save.

Delete the GW Sig Port

To delete any of the created a GW Sig Port, click

  1. Click the radio button next to

...

  1. the name of the entry you want to delete.

...

Caption
0Figure
1Gw Sig Port Highlighted

Image Removed

...

  2. Click the delete icon (X) at the end of the

...

  1. row.

...

  2. Confirm the deletion when prompted
Caption
0Figure
1Gw Sig Port Delete Confirmation

Image Removed

...

  1. .