Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.
Comment: removed obsolete cloud references

Add_workflow_for_techpubs
AUTH1
REV5
REV6
REV3
REV1

 

Panel

In this section:

Table of Contents
maxLevel4

Info
iconfalse

Related articles:

The Cluster Admin commands control communications among SBC nodes in a cluster configuration. You must configure the clusterAdmin clusterComm options on M-SBC clusters in a distributed SBC SWe deployment. This configuration is visible only for M-SBC clusters and must be completed prior to configuring a load balancing service to distribute media request among the media nodes.

Info
titleNote

You must restart the SBC after changing the IP address for intra-cluster communication.

Command Syntax

...

 

Command Parameters

 

The following syntax shows the first-level parameters under clusterAdmin. The subsequent options differ depending on the option you specify for type.

Code Block
% set system clusterAdmin clusterComm type <ip | mgmt>

clusterComm Syntax (M-SBC Deployments Only)

Intra-cluster communications can be configured to occur on either the management interface (default) or a packet interface. The parameters differ based on the type specification as shown below.

Code Block
titleclusterComm type = ip
% set system clusterAdmin clusterComm type ip
	addressContext <addressContext name>
	ipInterfaceGroup <IPIG name>
	pktIpVar <metaVariable>
Code Block
titleclusterComm type = mgmt
% set system clusterAdmin clusterComm type mgmt
   	mgmtInterfaceGroup mgmtGroup 
   	mgmtIpVar <metaVariable>

Command Parameters

The following table describes the parameters under clusterAdmin clusterComm you can use to configure intra-cluster communication for an M-SBC deployment.

Caption
0Table
1clusterComm Parameter Descriptions
ParameterLength/RangeDescription
typeN/A

Interface type to use for intra-cluster communication.

  • ip - to use a packet interface.
  • mgmt (default) - to use the management interface.
type = ip
addressContextN/AAddress context containing the IP interface group to use for intra-cluster communication.
ipInterfaceGroupN/A<IPIG name> – The name of the IP interface group for intra-cluster communication.
pktIpVar1-255 characters

<metaVariable> – The configuration metaVariable that specifies the IP address for intra-cluster communication.

 

type = mgmt
mgmtInterfaceGroupN/A

The management interface group for intra-cluster VNFC communication.

    • mgmtGroup (default)
mgmtIpVar1-255 characters

<metaVariable> – The configuration metaVariable that specifies the IP address for intra-cluster communication. (default = IF0.IPV6)

 

Configuration Examples

Excerpt

To configure packet interface using IPv6 address for VNFC communication in an M-SBC cluster:

Code Block
% set system clusterAdmin clusterComm type ip addressContext default ipInterfaceGroup MLIG2 pktIpVar IF3.IPV6
commit

 

To configure packet interface using IPv4 address for VNFC communication in an M-SBC cluster:

Code Block
% set system clusterAdmin clusterComm type ip addressContext default ipInterfaceGroup MLIG2 pktIpVar IF3.IPV4
commit

 

To configure management interface using IPv6 address for VNFC communication in an M-SBC cluster:

Code Block
% set system clusterAdmin clusterComm type mgmt mgmtInterfaceGroup mgmtGroup mgmtIpVar IFO.IPV6
commit

 

To configure management interface using IPv4 address for VNFC communication in an M-SBC cluster:

Code Block
% set system clusterAdmin clusterComm type mgmt mgmtInterfaceGroup mgmtGroup mgmtIpVar IFO.IPV4
commit

Info

Use the show table system clusterAdmin clusterComm command to view configuration details. Refer to Show Table System for details.

...

Pagebreak