Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Include Page
media_outage_Swe
media_outage_Swe
Anchor
BackToTopBackToTop

Spacevars
0longproduct
is deployed in a redundant High Availability (HA) configuration whereby a standby virtual machine (VM) protects the active VM. The HA configuration shares the data between the VMs which protect each other in a 1-1 redundancy model.

note
Info
title
Note

It is recommended that to install HA pair needs to be installed on two different physical hosts. For more information on setting up logical connections HA nodes, see Setting Up Logical Connection between Between High Availability Nodes. 

The following procedure describes how to install

...

the application

Spacevars
0product

...

software on HA system (both active and standby VM).

note
Info
title
Note
If any mistakes occur during the installation, you must reinstall the application. Before re-installing, execute the following commands from the console to check the application status and the DRBD status
:
Panel
bgColortransparent
titleCheck application and DRBD status
before reinstalling
  1. Enter the command:
    service sbx stop
  2. After the services are stopped, execute:
    service drbd stop
  3. Check the status of DRBD by executing:
    service drbd status
  4. Check the service status by executing:
    service sbx status

    The output should display:
    drbd not loaded

If the above output displays, it is safe to continue with the installation.

 

To install SBC SWe in HA mode:

  1. Launch the EMA. See Logging on to EMA in Platform Mode for guidance.

  2. Navigate to Administration > System Administration > Software Install/Upgrade tab. The Packages screen displays.

  3. Select the Package Name to install and click Install Software.

    Include Page
    Screenshot_disclaimer
    Screenshot_disclaimer
     

    Caption
    0Figure
    1Selecting SBC Package


    The Install Software section expands and displays the Install Version, Management Ports (configured in post-OS installation) and System Configuration details.

    Caption
    0Figure
    1Install SBC Application

    note
    Info
    title
    Note
    The signature file of the SBC package verifies the integrity of the package contents before proceeding with the SBC installation.

  4. Enter the System Configuration details.

    1. Select HA Pair in the HA Configuration field.
    2. Select System Name field and enter the system name.
    3. Select Local Hostname and enter local hostname.

    4. Select Peer Hostname and enter peer hostname.

      Noteinfo

      For more information, refer

      to

      to System Name and Hostname Conventions.

      Caption
      0Figure
      1Installation Configuration Screen

    5. Choose Choose the Active option for Server Role to designate the Active server as the one you are configuring.

    6. Keep default Active Primary CE IP.
    7. Keep default Standby Primary CE IP.
    8. Keep default Inter CE Prefix. The inter CE prefix is the netmask of the network in which the Inter CE IPs are configured.
    9. Use default TIPC NETID value (1500) if no other SBC SWe running in the same subnet.
    10. Select NTP Server IP field and enter the NTP server IP address.
    11. Select NTP Server Time Zone field and enter the NTP time zone.

  5. Click Start Installation.

     

    Caption
    0Figure
    1Starting the Installation

  6. The installation process starts and displays the installation status on the Installation Log section.

    1. Perform pre-install checks

      Caption
      0Figure
      1Pre-Install Checks

    2. Extract package contents

      Caption
      0Figure
      1Extracting Package Contents

    3. Install SBC service

      Caption
      0Figure
      1Installing SBC Service

      note
      Info
      title
      Note
      The installation checks whether ConnexIP OS version is compatible with the SBC application. If the OS upgrade is required, it performs the OS upgrade first and reboots the server. Once it is rebooted, login into the EMA again to continue with the SBC application.

    4. Initialize SBC service

      Caption
      0Figure
      1Initialize SBC Service

    5. Update Host Name

      Caption
      0Figure
      1Updating Host Name

    6. Reboot system

      Caption
      0Figure
      1Pre-Install Checks

  7. Log on to EMA platform. The new SBC application version displays on the Monitoring > Dashboard > System and Software Info.

    Caption
    0Figure
    1Displaying New SBC App Version

  8. Verify the system status using Administration > System Administration > Platform Management menu.

    Caption
    0Figure
    1Verifying System Status

    From the EMA, install the SBC licenses required in order to use SBC application and its features. See Managing SBC Licenses for guidance.

     

    Info
    titleNote
    Continue installing
    Note
    Continue upgrading
    the standby server once all the status is up and running.

  9. Repeat steps 2 through 8 to install the 

    Spacevars
    0prodkey
     application on the Standby peer, but with the following changes to steps 4c to 4e:

    • Step 4c. Enter Standby server name in Local Hostname field, which is typically the System Name with a letter b appended to the end.

    • Step 4d. Enter Active server name for Peer Hostname field, which is typically the System Name with a letter letter a appended appended to the end.

    • Step 4e. Choose Choose the Standby  option for Server Role to designate the Standby server as the one you are configuring.

    note
    Info
    title
    Note
    You must use the same System Name and TIPC NETID for both active and standby servers.
    Caption
    0Figure
    1Configuring Standby Server

  10. From the EMA, install the SBC licenses required in order to use SBC application and its features. See Managing SBC Licenses for guidance.

Pagebreak