...
...
borderColor | green |
---|
bgColor | transparent |
---|
borderWidth | 2 |
---|
...
Back to Table of Contents
Back to CLI Configure Mode
Back to Profiles - CLI
...
...
Multiexcerpt |
---|
MultiExcerptName | JIP Profile |
---|
|
Info |
---|
| JIP handling is only supported when using an external PSX in the network. |
The SBC supports sending Jurisdiction Information Parameter (JIP) |
...
...
information in SIP-SIP, SIP-SIP-I and SIP-I to SIP |
...
scenarios. A JIP value indicates the geographic location of the originating caller or switch. SIP JIP profiles are assigned to ingress and egress SIP trunk groups to determine what parameter to extract the SIP JIP value from in an incoming SIP INVITE message and in |
...
...
what parameter to place the JIP value in the outgoing message when sipJurisdictionSupport is enabled on the trunk group. The SBC can take the JIP value from or place it in the following parameters: rn parameter in the PAID headerjip parameter in the PAID headerrn parameter in the From headerjip parameter in the P-DCS-Billing-Info header
|
Multiple controls can be enabled at a time to select the header or parameter from which JIP value will be extracted. When multiple controls are configured, JIP information is extracted in the following order:
...
Command Syntax
Code Block |
---|
|
% set profiles services sipJipProfile |
...
<profile name>
jipParameterAs <userInfo | uriParam>
sendJipIn <rnPAI|jipPAI | rnFROM | jipPDCS>
useJipFromFROM <disabled | enabled>
useJipFromPAIjip <disabled | enabled>
useJipFromPAIrn <disabled | enabled>
useJipFromPDCS <disabled | enabled> |
Command Parameters
Caption |
---|
0 | Table |
---|
1 | Command Parameters |
---|
|
|
...
...
sipJipProfile
...
defaultJipProfile
– The default name of the JIP profile associated with ingress and egress SIP Trunk Group used to control the SIP header and the corresponding SIP parameter from which JIP value is extracted or sent.
...
<profile name>
| The name for the SIP JIP profile. A default profile, defaultJipProfile, is provided and assigned to SIP trunk groups by default. You have the option to create additional profiles and assign your own. | jipParameterAs |
|
...
| The parameter format to use when sending JIP information. uriParam – URI parameter, for example: P-Asserted-Identity: <sip:+12817267815@198.229.181.6:5060; transport=udp; user=phone;rn=+
|
|
...
- 1123456>
userInfo (default) – userinfo parameter, for example: P-Asserted-Identity: <sip:+12817267815;rn=+
|
|
...
- 1123456@198.229.181.6:5060; transport=udp; user=phone>
| sendJipIn |
|
...
Select the header/parameter option to send the JIP in the outgoing INVITE message: |
|
...
- The sends the JIP value in the rn parameter in the PAI header.
jipPAI –
|
|
...
- The sends the JIP value in the jip parameter in the PAI header.
rnFROM –
|
|
...
- The sends the JIP value in the rn parameter in the FROM header.
jipPDCS –
|
|
...
- The sends the JIP value in the jip parameter in the PDCS-Billing-Info header.
| useJipFromFROM |
|
...
...
allow extracting JIP information from the "rn" parameter in the FROM header of the INVITE message. disabled (default)enabled
| useJipFromPAIjip |
|
...
N/A
...
allow extracting JIP information from the "jip" parameter in the PAI header of the INVITE message. disabled (default)enabled
| useJipFromPAIrn |
|
...
N/A
...
allow extracting JIP information from the "rn" |
|
...
parameter in the PAI header of the INVITE message. disabled (default)
enabled
| useJipFromPDCS |
|
...
N/A
...
allow extracting JIP information from the "jip" |
|
...
parameter in the PDCS header of the INVITE message. disabled (default)enabled
|
|
Info |
---|
|
If you choose to enable more than one potential source from which to extract the JIP information, the SBC prioritizes them in the following order: rn parameter in the PAID headerjip parameter in the PAID headerrn parameter in the From headerjip parameter in the P-DCS-Billing-Info header
|
Command Examples
Code Block |
---|
|
% set profiles services sipJipProfile sjp2 useJipFromPAIjip enabled sendJipIn rnFROM jipParameterAs uriParam
% set profiles services sipJipProfile sjp2 useJipFromPAIrn enabled sendJipIn jipPDCS jipParameterAs userInfo
% show profiles services sipJipProfile sjp2
useJipFromPAIrn enabled;
sendJipIn jipPDCS;
jipParameterAs userInfo;
> show table profiles services sipJipProfile
USE JIP USE JIP USE JIP USE JIP JIP
FROM FROM FROM FROM SEND PARAMETER
NAME PAIRN P AIJIP FROM PDCS JIP IN AS
----------------------------------------------------------------------------------
sjp1 disabled enabled disabled disabled rnFROM uriParam
sjp2 enabled disabled disabled disabled jipPDCS userInfo
defaultJipProfile disabled disabled disabled disabled rnPAI userInfo |