Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Panel

...

borderColorgreen
bgColortransparent
borderWidth2

...

Back to Table of Contents

Back to CLI Configure Mode

Back to Operations and Maintenance - CLI

In this section:

Table of Contents

Info
iconfalse

Related articles:

 

...

In this section:

...

SNMP community strings are text strings that act as a rudimentary authentication mechanism for SNMP v1/v2. An SNMP manager places a community string (in plaintext) into an SNMP request when sending the request to a managed device such as an

Spacevars
0product
Spacevars
0model1
. The SNMP agent in a managed device ignores SNMP requests that do not contain a community string matching with the previously configured one. The
Spacevars
0product
supports configuring up to eight SNMP community strings using the communityString object described below.

Info
For additional details about configuring SNMP,

...

refer to Configuring SBC for SNMP.

Command Syntax

Code Block
languagenone
% set oam snmp
	communityString
		<snmpCommunity_Index>
		snmpCommunityName <community name>
	localEngineId <Id>
	securityLevel <authNoPriv | authPriv | noAuthNoPriv>
	trapTarget <trap target name>
		ipAddress <IP address>
		port <port number>
		state <disabled | enabled>
		targetSecurityLevel <authNoPriv | authPriv | noAuthNoPriv>
		targetUserName <name>
		trapType <inform | v1 | v2 | v3>
	users <username>
		authKey <colon separated hex string>
		authProtocol <HMACMD5 | HMACSHA>
		group <admin | user | operator>
		privKey <colon separated hex string>
		privProtocol <DES | AES128>
	version <v1v2c | v3only>

% show oam snmp trapTarget <trap target name>
   displaylevel <displaylevel>
   ipAddress <IP address>
   port <port number>
   state <disabled | enabled>
   trapType <inform | v1 | v2>
 
% delete oam snmp trapTarget

Command Parameters

Caption
0Table
1SNMP Parameters
 

Parameter

Length/Range

Description

communityStringN/A

SNMP Community String. A maximum of eight community strings may be configured.

  • <community string Index> – The index of this SNMP Community String (length: 1-32 characters).
  • snmpCommunityName – The name of the Community String.
localEngineId5-32 octetsThe value of User-based Security Model (USM) user engine ID and the SNMP community context engine ID.
securityLevelN/A

The vacm security level for all users in model 0 and 3. Options are:

  • authNoPriv – Authenticated but unencrypted
  • authPriv (default) – Authenticated and encrypted
  • noAuthNoPriv – Unauthenticated and unencrypted

trapTarget

N/A

<trapTarget name> – The name of the trap target.

  • ipAddress – The IP address of the trap target, which can be of type:
    • IPv4 – This is V4 IP address in dotted decimal form (for example, 128.127.50.224).
    • IPv6 – This is V6 IP address in hexadecimal/colon form (for example, 1280:1276:3350:2224:2222:3333:8888:1245 or fd00:21:445:128::7880)
  • port – The port number for SNMP traps (range: 1-65535 / default = 162).
  • state – Configured state of the trap target entry. Options are:
    • disabled (default) – No traps are sent to the trap server.
    • enabled– Traps are sent to the trap server.
  • targetSecurityLevel– The trap target security level.
    • authNoPriv – Authenticated but unencrypted
    • authPriv (default) – Authenticated and encrypted
    • noAuthNoPriv – Unauthenticated and unencrypted
  • targetUserName – The trap target SNMPV3 security name (up to 32 characters).
  • trapType– The type of the trap sent to the target. Options are:
    • inform – SNMP notifications will be sent to the trap target server.
    • v1 – SNMPv1 traps will be sent to the trap target server.
    • v2 (default) – SNMPv2 traps will be sent to the trap target server.
    • v3 – SNMPv3 traps will be sent to the trap target server.
Note

Up to 32 trap targets can be configured on the SBC.

usersN/A

<username> – Use this parameter to define SNMP users for the USM privacy facility. Enter a user name, and then choose from the options below:

  • authKey – SNMPv3 authentication key (colon separated hex string). Once set, the user cannot retrieve this value.
  • authProtocol –  The type of authentication protocol to use.
    • HMACMD5
    • HMACSHA (default)
  • group – Choose the user's group type:
    • admin
    • user
    • operator
  • privKey – SNMPv3 privacy key (colon separated hex string). Once set, the user cannot retrieve this value.
  • privProtocol– The privacy protocol to use:
    • DES
    • AES128 (default)
version

 N/A

The SNMP versions to support in SNMP configuration. Set to "v3only" if using SNMPv3 trap configuration.

  • v1v2c (default) – Support SNMPv1 and SNMPv2.
  • v3only – Support SNMPv3 only.

Command Example

To display the configuration of SNMP parameters:

Code Block
languagenone
% show oam snmp
trapTarget emaTarget {
    ipAddress 127.0.0.1;
    port      8162;
    trapType  v2;
    state     enabled;
}
version       v1v2c;
localEngineId 80:00:0b:3f:03:00:10:6b:2e:e5:e8;
securityLevel authPriv;
users admin {
    group        admin;
    authProtocol HMACSHA;
    authKey      00:00:00:00:00:00:00:00;
    privProtocol AES128;
    privKey      00:00:00:00:00:00:00:00;
}
users guest {
    group        guest;
    authProtocol HMACSHA;
    authKey      00:00:00:00:00:00:00:00;
    privProtocol AES128;
    privKey      00:00:00:00:00:00:00:00;
}
users operator {
    group        operator;
    authProtocol HMACSHA;
    authKey      00:00:00:00:00:00:00:00;
    privProtocol AES128;
    privKey      00:00:00:00:00:00:00:00;
}