Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_docset_workflow
AUTH1bscoggins
DEV1ssrinivasrao
LDEV1bscoggins
SVT1ssrinivasrao
LSVT1bscoggins
AUTHJIDSBX-42095

 

Noprint
Panel
borderColorgreen
bgColortransparent
borderWidth2

Back to Table of Contents

Back to Configuration

Back to Configuration - System Provisioning

Back to Category - Trunk Provisioning

Back to System Provisioning - Ip Peer

Panel

In this section:

Table of Contents
maxLevel2

This profile specifies the configuration for OPTIONS PING.

To View and Edit Path Check

On SBC main screen, go to Configuration > System Provisioning > Category: Trunk Provisioning > Ip IP Peer > Path Check. The Path Check window is displayed.

The Path Check can be checked for each Address Context, for each Zone, for each Ip IP Peer created or for all the Address Contexts, Zones and Ip IP Peers created. Use the drop-down box to select the desired Address Context, Zone and Ip IP Peer.

Caption
0Figure
1Ip IP Peer - Path Check Main Fields
 

Image Modified

The Edit Path Check window is displayed.

Caption
0Figure
1Ip IP Peer - Path Check Edit Window
 

Image Modified

The following fields are displayed:

Caption
0Table
1IP Peer - Path Check
 

 

Parameter

Description

Profile

Specifies the path check profile name used for OPTIONS ping.

Host Name

Specifies the FQDN value of the peer. It will be resolved using DNS and the resulting servers will be pinged using SIP OPTIONS requests. The value ranges up to 63 characters.

Note

If  IP Address is configured and Path Check needs to be enabled for that IP Address, ensure Host Name is not configured.

Host Port

Specifies the TCP/UDP port number of the peer. The peer's servers will be pinged using SIP OPTIONS requests at this port. The value ranges from 0 to 65535 and the default value is

...

5060.

Note

If   IP Port is configured and Path Check needs to be enabled for that IP Port, ensure Host Port is not configured.

When set to 0, the pathCheck task performs SRV lookup to resolve the port numbers. The resolved port numbers are used to send OPTIONS ping to the IP Peer.

When hostPort is set to value other than the value 0, the pathChecktask does not perform SRV lookup. It uses the configured port to send OPTIONS ping to the IP Peer.

Note

If hostPort is set to 0, SBC supports SRV,

State

Specifies if the active pinging is enabled or not. The options are:

  • enabled
  • disabled (default)

Status Update
Support

Enable this flag to provide Options-based status update support. The options are:

  • enabled
  • disabled (default)
Note

Status Updates only apply when new calls are sent to a peer. They do not impact messages belonging to existing calls or new calls received from the peer.

Status Update is Seen By:When:
PeerPeer restarts
PeerPeer is manually blocked
PeerPeer's congestion state changes (this update is ignored by SBC)
SBCPeer has restarted indicating it is ready to receive calls
SBCPeer is manually blocked in SBC.



Make the required changes and click Save at the right hand bottom of the panel to save the changes made.

Include Page
Path_Check_Profile_vs_ARS_Profile
Path_Check_Profile_vs_ARS_Profile

Path Check Commands

This option provides local admin state and remote admin state for a peer.

Caption
0Figure
1Ip IP Peer - Path Check Commands
 

Image Modified

The following options are displayed:

Caption
0Table
1IP Peer - Path Check Commands Parameters
 

 

Parameter

Description

locaAdminState

Specifies the local admin state of the peer. The options are:

  • block
  • unblock 
remoteAdminState

Specifies the remote admin state of the peer. The options are:

  • block
  • unblock 

 

Select the required command and click Select. A pop window appears seeking your preference for the selected Path Check Command.

Caption
0Figure
1Ip IP Peer - Path Check Command pop up window
 

Image Modified

Select the desired option and click the "Command Name" button to implement the option. The result of the action is displayed.

Click OK to exit.

LSWU Behavior

There are following three LSWU scenarios when SBC is upgraded from an older version which does not support DNS SRV pathCheck to a new version which supports DNS SRV pathCheck:

  • When hostPort is not configured in the older version, after the upgrade, the newer version displays the default value as 5060.
  • When hostPort is configured as 0 in the older version (default value in the older version), after upgrade, the newer version continues to use the same value (0) and SRV query is invoked.
  • When hostPort is configured to any other value in older version, after upgrade, the newer version continues to use the same value and SRV is skipped.