Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
JIRAIDAUTHCHOR-1210
REV5UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cd0f0958, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cc5207f0, userName='null'}

Include Page
_UX_Upgrade_Warning
_UX_Upgrade_Warning
nopaneltrue

Info

The Software Upload progress bar is supported in the following browsers:

  • Internet Explorer, Releases 10 and 11
  • Firefox, Release 24 and later
  • Chrome, Release 31 and later

In browsers that do not support this feature, the software upgrade process will be presented the way it is shown in Release 4.0 and previous.

To upgrade the inactive partition:

  1. In the WebUI, click the Settings tab.

  2. In the left navigation pane, go to System > Software Management > Application Partitions.

    Panel
    borderStylenone

    Caption
    0Figure
    1Partitions Table

    Image Modified

  3. Make note of the inactive partition number you are upgrading the firmware to (the table entry listed without a tick mark under the 'Active Partition' column).
    This will be important towards the end when verifying the last upload status of the inactive partition.

  4. Click the Upload Firmware link located on the top right hand side of the pane - a popup window will be dispatched:

...

Image Removed

...

  1. Panel
    borderStylenone

    Caption
    0Figure
    1Upload Firmware

    Image Added

  2. Under Select File, click the Browse button and select the Sonus SBC 1000/2000 firmware file listed in the general Sonus SBC 1000/2000 Upgrade guide to upload. Click OK. Do not close or navigate away from the browser window or you may  receive partial results.   

...

  1. Panel
    borderStylenone

    Caption
    0Figure
    1Select File

    Image Added

     

  1. Throughout the upload process, the web interface displays update messages to indicate the progression of the upgrade of the inactive partition, as shown below. (If you navigate to this view from another browser, it will also display the progress.)

...

  1. Panel
    borderStylenone

    Caption
    0Figure
    1Upgrade Progress

    Image Added

      

  2.  Once

Image Removed

Info

Under normal conditions, an average upgrade takes about 8 - 9 minutes. During the upgrade process, the remaining time estimates in the different steps becomes more accurate as the process progresses.

...

  1. the upgrade has completed, click the X in the corner of the box to dismiss the popup window.

...

  1.  On the partition page, verify the Last Upload Status associated with the inactive partition is listed as Success.                                                                               

Pagebreak

Info

Under normal conditions, an average upgrade takes about 8 - 9 minutes. During the upgrade process, the remaining time estimates in the different steps becomes more accurate as the process progresses.

Tip

At this stage, the inactive partition is upgraded to the the new firmware without rebooting the Sonus SBC 1000/2000 system and without interrupting active call services.

If you wish to boot your Sonus SBC 1000/2000 from this partition, you must set it as the active partition.

...

 

...