Versions Compared

Old Version 1

changes.mady.by.user Ribbon Communications

Saved on

compared with

New Version Current

changes.mady.by.user Ribbon Communications

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

Add_workflow_for_techpubs
AUTH1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cb8305e9, userName='null'}
JIRAIDAUTHCHOR-1208
REV5UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'}
REV6UserResourceIdentifier{userKey=8a00a0c85b2726c2015b58aa779d0003, userName='null'}
REV3UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cba30625, userName='null'}
REV1UserResourceIdentifier{userKey=8a00a02355cd1c2f0155cd26cc7d083d, userName='null'}

This document describes the recommended procedure for upgrading 

Spacevars
0series3
 to the latest release.

 

Panel

In this section....

Table of Contents

Panel

Related Pages:

Before You Begin...

 

You will need current software maintenance to perform the upgrade.


Note
titleRecommendations
  • Software upgrades should be performed during off-peak hours.
  • Before upgrading or staging an upgrade, Sonus recommends that you set all Logging to Error level unless advised by Sonus support. For information about logging, see Supported Logging Levels.

 

You will need current software maintenance to perform the upgrade.

 

Warning

Upgrading Release 6.1.x to Release 7.0 on KVM:

Installing Release 7.0 on KVM requires VirtIO as the disk bus. If IDE is used, performance decreases and packet loss occurs after 100 calls.

Warning
titleSTOP
Read the release notes for the target
Spacevars
0series3
software version. The upgrade notes (in particular) contain important information that may be relevant to your 
Spacevars
0series3
configuration. A newer version of 
Spacevars
0series3
may have different requirements than the previous version.

 

StepActionNote
1Make sure your environment still complies with the 
Spacevars
0series3
 requirements and supported platforms.		The End of Support Announcements for SWe Lite page has important information regarding platform support for future versions of
Spacevars
0series3
.
2Backup your Sonus SBC SWe data in the unlikely event that you encounter an issue with your 
Spacevars
0series3
upgrade and need to roll back.		 
3

Clear all outstanding alarms. To clear alarm(s), follow the instructions outlined in Acting on Displayed Alarms.

If you encounter any problems with your production upgrade that you cannot resolve in a timely manner, create an issue at our support site so we can assist you.

 

 Performing the Upgrade

 

 

Step

Action

Notes

1

From the Sonus SBC Download Center, download the SBCSWeLite-hv-release-x.y.z.buildnnn.img.gz where hv indicates the hypervisor, x.y.z indicates the upgrade version number and nnn indicates the build number.  Make note of the location to which you saved the file.

Anchor
Saved File Location
Saved File Location

Info

Ensure you download the appropriate file for your hypervisor.


Refer to Downloading the SBC SWe Lite Package for details.

2

Select the desired 

Spacevars
0series3
upgrade method:

 

3

Ensure the 

Spacevars
0series3
has upgraded by verifying the running software version.

 

Anchor
One-Step Upgrade
One-Step Upgrade

One-Step Upgrade 

 

  1. In the WebUI, click the Tasks tab.

  2. In the left navigation pane, click System > Software Upgrade.

  3. Backup the configuration file.

  4. Enter an optional Passphrase (see Using the Custom Passphrase).                                                    

  5. Under Select File, click the Browse button and select the SBC SWe Lite file you previously saved.

  6. Click Upgrade. 

  7.  Click OK to upload the new software. Do not close or navigate away from the browser window, or you may receive partial results. Throughout the upload process, the web interface displays update messages to indicate the progression of the upgrade, as shown below. (If you navigate to this view from another browser, it will also display the progress.) Once the upgrade is complete, the system automatically reboots.

     

A typical upgrade takes about 5 minutes. During the upgrade process, the remaining time estimates in the different steps becomes more accurate as the process progresses.

 

Upon completion, you will be automatically redirected to the Login screen. Verify that you are booting from the new partition either by checking the active partition, or by Viewing the Software Version.

Anchor
Upgrading the Inactive Partition
Upgrading the Inactive Partition

Upgrading the Inactive Partition

  1. In the WebUI, click the Settings tab.

  2. In the left navigation pane, go to System > Software Management > Application Partitions.

  3. Make note of the inactive partition number to which you are upgrading the software (the table entry listed without a tick mark under the 'Active Partition' column). This will be important towards the end when verifying the last upload status of the inactive partition.

  4. Click the Upload Software link located on the top right hand side of the pane.

  5. Under Select File, click the Browse button and select the SBC SWe Lite file you previously saved.

  6. Click OK. Do not close or navigate away from the browser window or you may  receive partial results.
  7. Once the upgrade has completed, click the X in the corner of the box to dismiss the popup window.
  8. On the partition page, verify the Last Upload Status associated with the inactive partition is listed as Success. 
     

Note

Throughout the upload process, the web interface displays update messages to indicate the progression of the upgrade of the inactive partition, as shown below. (If you navigate to this view from another browser, it will also display the progress.)


Under normal conditions, a typical upgrade takes about 5 minutes. During the upgrade process, the remaining time estimates in the different steps becomes more accurate as the process progresses.

 

At this stage, the inactive partition is upgraded to the the new software without rebooting the SBC SWe Lite and without interrupting active call services. To set as the active partition, refer to Setting the Active Partition.

 

Post-Upgrade Checklist

StepAction
1Clear Clear your web browser cache before you login to the
Spacevars
0series3
.
2

Perform a backup of your data on the new 

Spacevars
0series3
version. Sonus recommends that you rename the backup filename to indicate the current software version and build number.

3

Ensure there are no new alarms generated after the upgrade. In the event of finding new alarms, address what is causing them.

 

 

Pagebreak