Page History

This section describes 

Spacevars
0 series3

 hardware and software requirements and recommendations.

To install and configure 

Spacevars
0 series3

, make sure the Virtual Machine (VM) host meets the following recommended hardware, server platform and software requirements.

Warning
icon false
The recommended hardware and software settings are intended to ensure optimum stability and performance. If the recommended settings are not used, the Spacevars 0 series3 may not behave as expected.

License Requirements

You must obtain and apply a valid

Spacevars
0 product3

 license in order to configure and use the 

Spacevars
0 product3

. See below:

• If you are deploying an

  Spacevars
  0 series3

   trial instance (as described at SBC SWe Edge Trial Offer for On-Premises Deployment ) please refer to Obtaining and Installing an SBC SWe Edge Production Node-Locked License for license instructions;
• If you are not deploying a trial instance, please follow license instructions posted at Obtaining and Installing an SBC SWe Edge Production Node-Locked License.

Server Hardware Requirements

Multiexcerpt
MultiExcerptName Hyper-V Hardware Requirements
Configuration  Requirement Processor 2nd Generation Intel Core or Intel Xeon Processor (Sandy bridge or later) RAM Each  Spacevars 0 series3  instance requires from 1.5 GiB to 4 GiB of RAM depending on the configuration Drive Space Hard disk requirements are dependent upon the number of VMs hosted, the size of each VM at full size, and whether checkpoints will be enabled. Architecture 64-bit Intel processor Host OS HyperV Win Server 2022 Microsoft Windows Server 2022 Microsoft Windows Server 2019 Microsoft Windows Server 2016 Windows 10 Enterprise Minimum Hyper-V hosting requirements are posted by Microsoft. Info The  Spacevars 0 series3 does not support execution within a Hyper-V cluster, as defined at technet.microsoft.com. Contact your Spacevars 0 company sales representative if you have any questions.

BIOS Setting Recommendations

Spacevars
0 company

recommends the following BIOS settings for optimum performance:

Caption
0 Table 1 Recommended BIOS Settings for Optimum Performance
BIOS Parameter Recommended Setting Details Intel VT-x (Virtualization Technology) Enabled For hardware virtualization Intel Hyper-Threading Enabled

Note
icon false
BIOS settings and recommendations must not be changed once it is applied on the server.

Spacevars
0 company

Recommendations for

Spacevars
0 series3

General Recommendations

• Plan enough resources (RAM, CPU, NIC ports, hard disk, etc.) for all the virtual machines (VMs) to run on a server, including resources needed by Hyper-V itself.
• Allocate each VM with only as much virtual hardware as that VM requires. Adding excess resources may not result in improved performance nor will improved performance or feature difference be supported. Refer to the SBC SWe Edge Performance and Capacity for sanctioned VM sizes and supported performance against sanctioned VMs.

• Disconnect or disable any physical hardware devices (Floppy devices, Network interfaces, Storage controllers, Optical drives, USB controllers, etc.) under BIOS settings that you will not be using to free up interrupt/CPU resources.

Caption
0 Table 1 VM Configuration Recommendations
Setting Minimum vCPU 1, 2, 4 and 10 supported RAM 1.5 GiB to support 1 vCPU 2 GiB to support 2 vCPUs 3 GiB to support 4 vCPUs 4 GiB to support 10 vCPUs vNIC 2  Spacevars 0 series3  is created with 5 Virtual Network Interfaces (vNIC); up to 3 interfaces may be disabled.  Note: One vNIC is mandatory for management. Virtual Hard Disk 5 GiB

 

Additional Information

• Minimal networking configuration requires the Management Network Interface and at least one Media Interface to be assigned.
• Each

  Spacevars
  0 series3

  VM will use approximately 5 GiB of Virtual Hard Drive space. Drive size is predetermined by the imported image.

Info
icon false
Refer to Downloading the SBC SWe Edge Package for On-Premises Deployment for software download instructions.

Pagebreak